About Setup Menus - Panasonic WV-CP480 Operating Instructions Manual

ABOUT SETUP MENUS

Opening/Closing the Setup Menu
It is possible to open the WV-CP480 TOP menu
by holding down the SET button for 2 seconds
or more while displaying camera pictures.
At first, the menu will be displayed in English.
Move the cursor to SETUP DISABLE using the
direction buttons and press the SET button to
change it to SETUP ENABLE so that the menu
becomes operable in selecting your language
and other parameters.
On the menu, you can check current settings
and perform settings to meet requirements.
To close the menu and return to camera picture, move the cursor to END and press the SET
button. (When no operation is performed for 5 minutes, the menu will automatically close.)
How to Set Up on the Menu
Operate the direction buttons (U: Up, D: Down,
L: Left, R: Right) and the SET button as shown
in the table below.
In the following pages, abbreviated expressions
will be used many times for convenience.
An abbreviated expression "Select CAMERA
and press SET" means "Move the cursor to
CAMERA by using the Up or Down button
and press the SET button." Buttons of LEFT,
UP, RIGHT, and DOWN are abbreviated as
L, U, R, and D respectively.
Function/Button
Open the menu
Move the cursor
Select a setup item
Select a parameter
Apply settings
Open a sub-menu
Close the menu
Return to the previous menu
Return to the top menu
Reset a specific item
Reset all*
1
Enable/Disable the menu *
Scroll up or down the page
Notes:
• NA: Not Applicable.
• *1 "Reset all" is an irrevocable procedure that resets all settings to the default values.
The PIX OFF setting will not be reset. We recommend that you take note of settings
before executing this command (except the PIX OFF settings).
• *2 Before operating the menu, change SETUP DISABLE (default setting) to
SETUP ENABLE.
• When closing the menu, the changed settings will be stored in the memory of the
camera and will remain until the settings are overwritten by new ones.
• Use a system controller to operate setup menus after installation as necessary. Almost
all operations will be available unless otherwise mentioned.
Top Menu and Sub Menus
The following menus will be displayed in the language selected on the LANGUAGE SETUP
menu.
There are four sub menus selectable on the top menu: CAMERA SETUP (2 pages), BACK-
FOCUS SETUP, SPECIAL SETUP, and LANGUAGE SETUP. On these menus, select a setup
item followed by "↓" and press the SET button to open more sub menus.
MODEL WV-CP480 SERIES
CAMERA
BACK-FOCUS
SPECIAL
LANGUAGE
END SETUP ENABLE
Up(U) Down (D) Right (R) Left (L)
NA NA
↑ ↓
↑ ↓
NA NA
NA NA
(Move the cursor to the item with ↓.)
(Move the cursor to END.)
(Move the cursor to RET.)
(Move the cursor to TOP.)
(Move the cursor to the item to be reset , press L and R simultaneously.)
(When camera picture is displayed, press L, R and SET simultane-
ously for 2 seconds.)
2 (Move the cursor to SETUP DISABLE/ENABLE, press SET)
(Hold down ↑ or ↓)
CAMERA ID
ALC/ELC
SHUTTER
AGC
SENS UP
SYNC
WHITE BAL
MOTION DET
DNR
RESOLUTION
BW MODE
**BACK-FOCUS SETUP**
ABF
MANUAL-ADJ
C/L← → B/W
SETUP-SW LOCK OFF
NEAR
.........I..........
INDICATOR 9999
RET TOP END
**SPECIAL SETUP**
CHROMA GAIN
AP GAIN
PEDESTAL
HUE
PIX OFF
COMMUNICATION COAX
CAMERA RESET →PUSH SW
SER.NO. XXXXXXXX
RET TOP END
LANGUAGE
SET
RET TOP END
CAMERA
BACK-FOCUS
SPECIAL
LANGUAGE
Left Button
NEAR
(LEFT)
(DOWN)
Set Button
NA
→
NA
→
NA
SETUP DISABLE
**CAMERA SETUP** 1/2
OFF
ALC
OFF
ON(HIGH)
OFF
INT
ATW1
OFF
HIGH
HIGH
→PUSH SW
AUTO
FAR
.....I...
...I.....
.....I...
....I....
-
**LANGUAGE SETUP**
ENGLISH
MODEL WV-CP480 SERIES
END SETUP DISABLE
Up Button
(UP)
ABF/MENU FAR
(SET) (RIGHT)
Down Button
Set(SET)
NA Press 2 seconds
←
NA
NA NA
←
NA
NA Press
Press
Press
Press
Press
SETUP ENABLE
**CAMERA SETUP** 2/2
PRIVACY ZONE
MIRROR
LENS-DRIVE
STABILIZER
RET TOP END
+
Right Button
OFF
OFF
DC
OFF