Operating Instructions Starting the Machine Suction Control Operating the Machine Additional Operating Instructions for K3 with Power Head Starting the Machine and Suction Control Operating the Machine Using the Telescopic Tube, Hose & Attachments Use and Maintenance of Brushes and Heads...
16. Do not use vacuum without filter bag and/or filters in place. either hose or power head. 17. Turn off all machine controls before unplugging. 33. Use a SEBO power head only in combination with a SEBO vacuum cleaner. 18. Use extra care when cleaning on stairs.
Typical vacuums perform poorly and usually do not last beyond two years. So, in the long run, SEBO vacuums cost less Liberation from Bagless! SEBO Bags are money than the five to six other vacuums purchased during that Hygienic –...
Page 5
AIRBELT K2: The SEBO AIRBELT K2 is a straight-suction vacu- Mid-sized Canister Vacuum – The SEBO um. As a result, it differs from the AIRBELT K3 in the following AIRBELT K3 and K2 are considered mid- two ways:...
OPTIONAL ATTACHMENTS, ACCESSORIES, BAGS & FILTERS SEBO filter bags can be purchased in boxes of eight and fil- In addition to the standard on-board tools, a variety of ters are sold separately. Also, bags and filters can be pur- optional attachments are available.
NOTE: To attach a SEBO power head (ET-H, ET-1 or ET-2) to your K3 canister, please refer to your power head owner’s manual for instructions. Attaching incorrectly could cause damage. NOTE: All illustrations shown in this manual represent the K3 model except where part numbers and instructions are different for each model...
When possible, consult the materials supplied by your flooring manufacturer for infor- mation on proper upkeep and cleaning. To ensure that your new SEBO vacuum cleaner is compatible with your floor, please test the vacuum cleaner on each type of flooring surface in a small inconspicuous area to determine if any damage occurs.
ADDITIONAL OPERATING INSTRUCTIONS FOR K3 WITH POWER HEAD Please refer to your power head owner’s manual for more information Starting The Machine and Suction Control - Figures 1, 2, 8, 9, 10a & 10b Before turning on your canister, make sure that the vacuum handle is in its upright locked position (figure 8).
Figure 11 NOTE! K3 users with ET-H, ET-1 or ET-2 power heads, please refer to your power head user’s manual for more detailed instructions for connecting your power head.
AIRBELT cover around the foam (54) into the opposite groove (56). Continue around the vacuum. Secure the ends with the clip (55). SEBO AIRBELT covers are available in a variety of colors and patterns. See AIRBELT Cover - Part #6047AM/01-08 your SEBO dealer for available selection.
CLOG REMOVAL Always unplug vacuum from outlet before removing any clogs! NOTE! K3 users with ET-H, ET-1 or ET-2 power heads, please refer to your power head user’s manual for more detailed instructions for removing clogs in your power head.
2. Use another outlet. 3. Cable worn. 3. Replace cable. 4. K3: The power control slider 4. K3: Set slider switch to “on” switch is set to “0” (“off” position). position. See page 9. Bag full or clog light on 1.
Bag holder, complete 6696AM K Microfilter & Exhaust set 6756DG Bag cover, complete (incl. castor 6752DG) 6607DG Cover release 6629AM Filter bag SEBO K 6752DG Castor cpl. (New castor for bag cover 6756DG) 6652 Cable rewind 6621 Switch lever 1739...
To locate an authorized SEBO dealer in your area, or to with your new SEBO vacuum cleaner. You may also reg- register a warranty claim in the United States of ister on our website at www.sebo.us.
Need help?
Do you have a question about the AIRBELT K3 and is the answer not in the manual?
Questions and answers