Vent Installation; Application; Vent Parts List - Lennox Hearth Products Ravelle 30 Installation And Operation Manual

VENT INSTALLATION

Application:

The Ravelle™ 30 gas fireplace, has been tested and listed as a direct
vent heater system by OMNI-Test Laboratories, Portland, Oregon and is
recommended for use with Security™ Secure Vent™ pipe.
IMPORTANT:
• Read all instructions carefully before starting the installation.
Failure to follow these instructions may create a fire or other
safety hazard and will void the warranty. Be sure to check for
specific clearances to combustible requirements on Page 6.
Do not extend the venting system vertically or horizontally in
excess of the distance prescribed on Page 17. Consult your
local building codes before beginning the installation.
• Always maintain the proper air spaces (see Page 6) between
the vent pipe and nearby combustibles to prevent a fire hazard.
Do not fill air spaces with insulation. Be sure to check the
vent termination clearance requirements from decks, windows,
soffits, gas regulators, air supply inlets and public walkways,
as specified in these installation instructions on Page 18 and
local building codes.
• This gas appliance and vent system must be vented directly to
the outside of the building and never be attached to a chimney
serving a separate solid fuel or gas-burning appliance. Each
direct vent gas appliance must use its own separate vent system.
Common vent systems are prohibited.
• The Ravelle 30 gas fireplace is recommended for use
with Security Secure Vent pipe. The appliances and vent
manufacturers warranties will be voided and serious fire, health,
or other safety hazards may result from any of the following
actions:
• Installation of any damaged direct vent component.
• Unauthorized modification of the direct vent system.
• Installation of any vent component part not approved or
manufactured by the approved vent manufacturer.
• Installation other than as instructed by Lennox Hearth
Products and vent manufacturers instructions.
1
Vent Parts List
Direct vent pipe Security™ Secure Vent™* may be used with the Ravelle 30
gas fireplace. Please see the lists below to verify the components available
from each direct vent pipe manufacturer. Snorkel terminations are available
for applications which may require vertical rise on the building exterior.
The components listed below come in a galvanized finish. Most of the
components are also available in a painted black finish. Add a "B" to the
end of the part number when ordering if a black part is desired.
Part Number
SV4L6
SV4L12
SV4L24
SV4L36
SV4L48
SV4LA
SV4LA12
SV4FA
SV4FB
SV4RSM
SV4E46
SV4E90
SV4VS
SV4FC
SV4CGV
SV4BF
SV4CHC
SV4STC36
SV4STC14
SV4BM
Part Number
908
907
906
904
903
902
911
912
917
942
943
943S
945
950
953
963
980
981
982
984
985
988
991
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Security™ Secure Vent 6-5/8"x 4" Pipe
Description
6" Pipe Length
12" Pipe Length
24" Pipe Length
36" Pipe Length
48" Pipe Length
6" Pipe, Adjustable
12" Pipe, Adjustable
Flashing, 1/12 to 176/12 Roof Pitch
Flashing, 8/12 to 12/12 Roof Pitch
Wall Radiation Shield
45° Elbow
90° Elbow
Vinyl Shield Protector
Storm Collar
Vertical Termination Cap
Firestop
Horizontal Termination Cap
Snorkel Termination (36") Cap
Snorkel Termination (14") Cap
Wall Band
Simpson DuraVent 6-5/8"x 4" GS Pipe
Description
6" Pipe Length
9" Pipe Length
12" Pipe Length
24" Pipe Length
36" Pipe Length
48" Pipe Length
11" to 14-5/8" Pipe, Adjustable
12" to 17" Pipe, Adjustable
17" to 24" Pipe, Adjustable
Wall Thimble
Flashing, 0/12 to 6/12 Roof Pitch
Flashing, 7/12 to 12/12 Roof Pitch
45° Elbow
Vinyl Siding Standoff
Storm Collar
Ceiling Firestop
Vertical Termination
Snorkel Termination (36")
Snorkel Termination (14")
Horizontal Square Termination
Horizontal Square Termination (High Wind)
Wall Strap
Vertical Termination (High Wind)