GE JV694 Use And Care & Installation Manual
Ge 36" vented hood - use and care & installation guide
Hide thumbs
Also See for JV694:
- Use and care & installation manual (9 pages) ,
- Use and care & installation manual (9 pages) ,
- Use and care & installation manual (8 pages)
Table of Contents
Advertisement
Quick Links
Use and Care & Installation Guide
Safety Instructions
Operating Instructions
Automatic Heat Sensor ...........................3
Controls .....................................................2
Cleaning
....................................................
Filter............................................................3
Light Bulb Replacement..........................3
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
SAFETY PRECAUTIONS
WARNING –
TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended
by the manufacturer. If you have questions,
contact the manufacturer.
B. Before servicing or cleaning unit, switch
power off at service panel and lock the service
disconnecting means to prevent power from
being switched on accidentally. When the
service disconnecting means cannot be locked,
securely fasten a prominent warning device,
such as a tag, to the service panel.
C. Do not use this unit with any solid-state speed
control device.
D. Use with approved cord-connection kit only.
E. This unit must be grounded.
ge.com
36 " Vented Hood
...Front Cover, 2
.........2, 3
3
WARNING –
RANGE TOP GREASE FIRE:
A. Never leave surface units unattended at high
settings. Boilovers cause smoking and greasy
spillovers that may ignite. Heat oils slowly on
low or medium settings.
B. Always turn hood ON when cooking at high
heat or when cooking flaming foods.
C. Clean ventilating fans frequently. Grease should
not be allowed to accumulate on fan or filter.
D. Use proper pan size. Always use cookware
appropriate for the size of the surface
element.
Models: JV694 JV695 JV696 JV960
Installation
.....................................4–6
Damper/Duct Connector .........................5
Electrical Wiring .......................................6
Filter Panel.............................................3, 5
Mounting Brackets...................................5
Consumer Services
Important Phone Numbers.....................7
Warranty ..................................Back Cover
TO REDUCE THE RISK OF A
(continued next page)
.....................7
Advertisement
Table of Contents
Related Manuals for GE JV694
Summary of Contents for GE JV694
-
Page 1: Important Safety Information
C. Do not use this unit with any solid-state speed (continued next page) control device. D. Use with approved cord-connection kit only. E. This unit must be grounded. ge.com Models: JV694 JV695 JV696 JV960... -
Page 2: Operating Instructions
IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING. SAFETY PRECAUTIONS CAUTION – WARNING – For general ventilating use only. Do not TO REDUCE THE RISK OF FIRE, use to exhaust hazardous or explosive materials and vapors. ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: WARNING –... -
Page 3: Care And Cleaning
If the ends of the tube light but the center does not, National Parts Center1.800.626.2002 the starter may require replacement. The starter is ge.com located behind the filter panel on the right hand side. Install the new starter by pushing the starter in and... -
Page 4: Installation Instructions
INSTALLATION INSTRUCTIONS TOOLS YOU WILL NEED This hood can easily be installed by following these basic steps: • Mark and cut out the cabinet bottom. • Secure the hood to the cabinet. Flat blade and Phillips Pencil • Mount the cabinet on the wall. screwdrivers •... - Page 5 INSTALLATION INSTRUCTIONS 2. Attach the damper/duct connector. 7. Install the mounting brackets. FRONT Hold the left hand mounting bracket in place on OF HOOD the side of the housing as shown. Use two (2) screws (provided) to attach the connector to the housing.
- Page 6 INSTALLATION INSTRUCTIONS 8. Secure the hood to the cabinet. 13. Install the glass visor assembly. VISOR Align the hood with the sides and front edge of the TRIM cabinet. Tighten the screws in each mounting bracket. Place plastic caps (provided) over the ends of these screws from the inside of the cabinet.
- Page 7 We’ll Be There With the purchase of your new GE appliance, receive the assurance that if you ever need information or assistance from GE, we’ll be there. All you have to do is call—toll-free! GE Answer Center ® 800.626.2000 ®...
-
Page 8: Warranty
Customer Care ® technician. To schedule service, on-line, 24 hours a day, visit us at ge.com, or call 800.GE.CARES (800.432.2737). Please have serial number and model number available when calling for service. • Service trips to your home to WHAT IS NOT COVERED •...