Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Aztech WL559E
Summary of Contents for Aztech WL559E
- Page 1 WL559E Portable 300Mbps Wireless-N Repeater...
-
Page 2: Table Of Contents
Wireless Repeater ..................21 Wireless Access Point ................23 Wireless Bridge..................24 WPS ......................25 Configure WL559E to Wireless Router via WPS ............. 25 Configure WL559E to Wireless client via WPS ............25 Safety Precautions ................. 26 Page 2 of 27... -
Page 3: About The Device
Wireless Repeater ..................21 Wireless Access Point ................23 Wireless Bridge..................24 WPS ......................25 Configure WL559E to Wireless Router via WPS ............. 25 Configure WL559E to Wireless client via WPS ............25 Safety Precautions ................. 26 Page 3 of 27... - Page 4 | WL559E User Manual Aztech Page 4 of 27...
-
Page 5: About The Device
W W W W i i i i F F F F i i i i N N N N e e e e t t t t w w w w ork WL559E supports robust 802.11n technology with up to 300Mbps data transfer rate. -
Page 6: Minimum System Requirements
| WL559E User Manual Aztech Minimum System Requirements Your computer must meet the following minimum requirements. Any operating system can be used Web Browser 233MHz processor Ethernet network adapter Or Wireless network adapter Package Contents Package contents are listed below. For any missing items, please contact your dealer immediately. -
Page 7: Top Panel
LED RRSI 3 BARS Connected 95% and above RSSI (Excellent) 2 BARS Connected 55-94% RSSI (Recommended) 1 BAR Connected 10-54% RSSI (Weak) Top Panel WPSW LABEL DESCRIPTION WPS BUTTON Connect WL559E to any WPS capable devices Page 7 of 27... -
Page 8: Bottom Panel
| WL559E User Manual Aztech Bottom Panel 10/100 Base-T Ethernet Port RESET LABEL DESCRIPTION RESET Press the Reset button for 5 seconds to restore the device to default factory settings ETHERNET PORT Connect to computers/Ethernet devices Page 8 of 27... -
Page 9: Accessing The User Interface
User Manual Accessing the User Interface To access the User Interface open a Web browser (Ex: Internet Explorer, Firefox or http://10.0.10.254 G.chrome) and type in the address bar and press enter. Quick Connect Quick Connect Press icon to scan for available wireless within the area. Page 9 of 27... -
Page 10: Setup
| WL559E User Manual Aztech Setup Mode of Operation Mode of Operation Mode of Operation Mode of Operation Repeater Repeater Repeater Repeater Configure your device as a wireless repeater to extend the wireless coverage of your wireless router. Access Point... - Page 11 User Manual 64bit – uses 10 characters length of password from A-F and numbers from 0-9 128bit- uses 26 characters length of password from A-F and numbers from 0-9 ASCII 64bit – uses 5 characters alpha numeric password (A-Z and 0-9) 128bit –...
-
Page 12: Wireless
| WL559E User Manual Aztech Wireless Wireless Basic Settings Enable Wireless Enable Wireless Enable Wireless Enable Wireless Enable or Disable wireless capability Broadcast SSID Broadcast SSID Broadcast SSID Broadcast SSID Set option to disable to hide your wireless network (Enable by default) -
Page 13: Wireless Security Settings
Registrar PIN Registrar PIN Here you can enter the WPS-PIN of wireless clients and click apply for the WL559E to allow access and configure your wireless client device automatically Note: WPS will work only for WPA-PSK, WPA2-PSK and WPA/WPA2 encryption. Wireless client should support WPS feature to use this option. -
Page 14: Mac Filter Settings
Aztech MAC Filter Settings This feature will provide additional protection to your wireless network. It allows or denies wireless clients from accessing through the WL559E with the use of the MAC address which is unique for every network devices. Policy... -
Page 15: System
User Manual Where can I find the MAC address of my wireless client? Where can I find the MAC address of my wireless client? Where can I find the MAC address of my wireless client? Where can I find the MAC address of my wireless client? ipconfig/all On the Command Prompt type to show all the network adapter(s) that are... -
Page 16: Lan Configuration
Device IP address Device IP address Device IP address Shows the device’s current IP address Note: Change this IP address if you are using two WL559E on the same network to avoid Note: Note: Note: IP address conflict within your network. You may configure the 2 unit with IP address ex: 10.0.10.253... -
Page 17: Configuration Settings
User Manual Configuration Settings Backup Settings Backup Settings Backup Settings Backup Settings Allow you to save the current configuration of WL559E. Default file name for the backup RT2880_Settings.dat”. file will be “ Click Apply Apply Apply Apply to start saving your configuration. -
Page 18: System Password
Apply to start the update. Apply Apply Note: Note: Note: Note: It is recommended to only use firmware which is officially release by Aztech, Using third party firmware will void the warranty of the device. System Password System Password System Password System Password Set a password on web user interface to prevent other users from getting access to the web UI and avoid unwanted changes from your settings. - Page 19 Type your password and click on apply to activate this feature. To disable, simply remove the password and click apply to save your settings. Note: Note: forgotten password will not be recovered. Reset the device pressing the reset button found beside Note: Note: the Ethernet port of WL559E. Page 19 of 27...
-
Page 20: Configuring The Device
| WL559E User Manual Aztech Configuring the Device Placement of the Wireless Repeater is crucial to get the best possible results for extending your existing wireless signal. It is ideal for the wireless repeater to be placed in a location where it can receive good wireless signal from the wireless router/AP so as to avoid disconnection and packet loss. -
Page 21: Wireless Repeater
User Manual Wireless Repeater a. Plug your WL559E to a power outlet, switch it ON and connect the Ethernet cable between your WL559E and Computer b. Launch web browser and you will be directed to the User Interface (In case it does not open type 10.0.10.254 and hit enter) - Page 22 | WL559E User Manual Aztech SETUP DIAGRAM (REPEATER) Modem Router WL559E Repeater Wireless Devices Page 22 of 27...
-
Page 23: Wireless Access Point
User Manual Wireless Access Point Setup your WL559E as an access point to provide wireless network to router that doesn’t have wireless feature. Plug your WL559E to a power outlet Connect an Ethernet cable between the WL559E and Computer Launch web browser and you will be directed to the User Interface... -
Page 24: Wireless Bridge
Ethernet port of the WL556E. a. Plug in and turn ON your WL559E b. Connect the Ethernet cable between your computer and WL559E c. Launch a web browser. You will be directed to the user interface d. Click on Setup... -
Page 25: Wps
User Manual WPS or Wifi Protected Setup makes it easier for you to connect your WL559E to your wireless router and WL559E to your wireless devices with a push of a button. (WPS feature must be enabled and must be supported on the wireless router and wireless... -
Page 26: Safety Precautions
| WL559E User Manual Aztech Safety Precautions Pluggable equipment must be installed near to an easily accessible socket outlet. Do not open, service, or change any component. Only qualified technical specialists are allowed to service the equipment. Observe safety precautions to avoid electric shock. - Page 27 User Manual Page 27 of 27...
Need help?
Do you have a question about the WL559E and is the answer not in the manual?
Questions and answers