Table of Contents
Related Manuals for Shark Shark NV70
Summary of Contents for Shark Shark NV70
- Page 1 NV70 Owner’s Guide www.sharkclean.com NV70_26_IB_E_130228_1.indd 1 13-02-28 1:48 PM...
-
Page 2: Technical Specifications
NV70 26 TECHNICAL SPECIFICATIONS Voltage: 120V. Watts: 1200W Amps: 10A Hertz: 60Hz Euro-Pro, Shark and Navigator are trademarks of Euro-Pro Operating LLC. All other brand names may be trademarks of their respective owners. TOLL FREE: 1-800-798-7398 NV70_26_IB_E_130228_1.indd 2 13-02-28 1:48 PM... -
Page 3: Table Of Contents
Contents Thank you for Important Safety Instructions purchasing Getting Started the Shark ® Using the Vacuum Navigator ™ Cleaning with the Vacuum Accessories DLX. Emptying the Dust Cup Assembly Proper Care of Your Vacuum Troubleshooting Checking for Blockages Maintenance Warranty and Registration www.sharkclean.com NV70_26_IB_E_130228_1.indd 1 13-02-28 1:48 PM... -
Page 4: Important Safety Instructions
POLARIZED PLUG: outdoors, or dropped into water, return it to EURO-PRO Operating LLC for examination, This appliance has a polarized plug (one blade repair, or adjustment. is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way. - Page 5 4. Only use filters and accessories provided by 3. Keep cleaning tools and hose suction EURO-PRO Operating LLC. [Failure to do so openings away from hair, face, fingers, will void the warranty.] uncovered feet,or loose clothing.
-
Page 6: Getting Started
Getting Started Your Shark Navigator ® ™ Secure the handle assembly in is easy to assemble: place with included nut/bolt (shipped attached to handle WHAT’S IN THE BOX YOU JUST Lay your vacuum body on a assembly). OPENED: level surface. Place the vacuum in the upright Vacuum Body Slide the electrical connection... - Page 7 Attach the Super Stretch Hose: To store the vacuum: To carry the vacuum: Snap hose into swivel When storing your vacuum, With the unit in the standing connector wind the cord around the two position, lift by the Dust Cup cord holders and secure with Assembly Handle (carry handle).
-
Page 8: Using The Vacuum
Using the Vacuum IMPORTANT: To protect your Release suction for carpets, the brushroll will only easier push and pull turn on when you have pulled on high pile carpets the handle back towards you and and area rugs. released the Floor Power Nozzle. Power Switch Settings Suction Release... -
Page 9: Cleaning With The Vacuum Accessories
Cleaning with the Vacuum Accessories Using the Cleaning Wand: Stand the vacuum into upright position. Remove the Cleaning Wand (with hose attached) from the unit. Vacuum Accessories Before cleaning with your Push the selected tool into the accessories: Your vacuum comes with a Super end of the Cleaning Wand. - Page 10 Maintenance CAUTION: For best results empty the Dust Cup Unplug the vacuum; failure to do Assembly after each use, as needed so might result in electric shock. during prolonged usage or when it reaches the MAX fill line. DO NOT OVERFILL. Turn vacuum off before emptying.
- Page 11 COMPONENT MAINTENANCE SCHEDULE Dust Cup Empty each time you vacuum. Pre-Motor Foam Filter Rinse and air dry every month under normal use. Pre-Motor Felt Filter Rinse and air dry every month under normal use. Post-Motor HEPA Filter Clean once a year under normal use. DO NOT operate the vacuum without ALL the filters in place.
-
Page 12: Troubleshooting
Troubleshooting WARNING: to reduce the risk of electric shock, the power cord must be disconnected before performing maintenance/troubleshooting checks. PROBLEM POSSIBLE REASONS & SOLUTIONS Check filters to see if they need cleaning. Follow instructions for rinsing and drying the filters before re-inserting back into the vacuum. (See “Maintenance”... -
Page 13: Checking For Blockages
Checking for Blockages Dust Cup Air Duct: Floor Power Nozzle Hose Unplug the vacuum before Connector: checking for blockages. Stand vacuum into upright position. Lay vacuum flat. Remove Dust Cup Assembly and Remove Nozzle Hose and check Reassemble all parts securely empty Dust Cup if necessary. -
Page 14: Maintenance
Maintenance Rotating Brush Cleaning The Pet Hair Brush Slide the locking latch (a) forward and tilt the bottom cover upward to remove. Carefully remove any blockage or debris and cut away any build-up of hair or string wrapped around the rotating Cleaning The Motorized Floor Resetting the Motor Thermostat bristle brush with scissors. - Page 15 The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option. This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes.
- Page 16 CAN: 4400 Bois Franc, St-Laurent, QC H4S 1A7 English: 1-800-798-7398 www.sharkclean.com Copyright © Euro-Pro Operating LLC 2013 Euro-Pro, Shark and Navigator are trademarks of Euro-Pro Operating LLC. All other brand names may be trademarks of their respective owners. Printed in China Illustrations may differ from actual product.