Conair Chopper GMT264GB Instructions For Care And Use

IMPORTANT SAfETY
wARNING
– To reduce the risk of burns,
electric shock, fire, or injury to persons:
INSTRUCTIONS
1. Never leave a plugged-in appliance unat-
tended.
When using electrical appliances, especially
2. This appliance should not be used by, on, or
when children are present, basic safety pre-
near children or individuals with certain dis-
cautions should always be taken, including
abilities.
the following:
3. Use appliance only for its intended use as
READ ALL INSTRUCTIONS
described in this manual. Only use attachments
BEfORE USING
recommended by the manufacturer. Do not use
an extension cord to operate the appliance.
fOR HOUSEHOLD USE ONLY
4. Never operate the appliance if it has a dam-
aged cord or plug, is not working properly, has
Keep away from water
been dropped or damaged, or dropped into
water. Return the appliance to a Conair service
DANGER center for examination and repair.
– Any appliance is electrically
5. Keep the appliance cord away from heated
live, even when the switch is off.
surfaces.
To reduce the risk of death or injury by electric
6. Do not pull, twist or wrap the cord around
shock:
the appliance.
1. Always unplug appliance from electri-
7. Never drop or insert any object into any open-
cal outlet immediately after using (except
ing of the appliance.
when charging unit).
8. Do not place the appliance on any surface
2. Do not place or store appliance where it
while it is operating.
could fall or be pulled into a tub or sink.
9. Do not use the appliance with a damaged
3. Do not use appliance while bathing or in
or broken comb or with teeth missing from the
the shower.
blades, as injury may result. Before each use,
4. Do not place appliance in, or drop into, water
make certain the blades are aligned properly
or other liquids.
and oiled.
5. If appliance has fallen into water, do not
10. Do not use the appliance outdoors or where
reach for it. Unplug immediately.
aerosol (spray) products are being used or oxy-
6. Unplug this appliance before cleaning.
gen is being administered.
DO NOT REACH
11. THIS PRODUCT IS fOR HOUSEHOLD
USE ONLY.
INTO THE wATER SAvE THESE
INSTRUCTIONS
USER MANUAL TROUBLESHOOTING
Before using the Class 2 Power Supply, read If your rechargeable trimmer does not seem to
these instructions carefully. be taking a charge, take the following trouble-
shooting steps before returning it for repair:
Model: SW-038011A
1. Be sure the electrical outlet is working by
Rated input voltage: 120Vac,
plugging in another appliance to test the outlet.
60Hz, 0.2 Amax
2. Make sure the electrical plug is not connected
Rated output: 3.8VDC, 110mA
to a switch which turns power off when lights
OPERATION
are turned off.
1. For dry location use only. Do not expose OPERATING INSTRUCTIONS
to water. 1. Before using your trimmer for the first time,
2. When not in use, unplug unit completely. charge continuously for 16 hours. Maximum
3. Never operate this unit if the specification battery capacity will only be reached after 3
is out of the rating. charging and discharging cycles. Always turn
4. When using this unit, a warm temperature
the ON/OFF switch to the OFF position when
will be reached.
charging.
2. Plug the adaptor into any wall outlet (at the
CAUTION
voltage listed on the label affixed to the adap-
1. Risk of electric shock, dry location use only
tor). Unplug adaptor when not in use.
or do not expose to liquid, vapor, or rain.
3. The adaptor may become warm while
2. Do not short the polarity (output cord).
charging. This is normal.
Ensure jack is plugged into the Trimmer unit
4. Preserving the battery: in order to maintain
before plugging the adaptor into the outlet.
the optimum capacity of the rechargeable
3. Do not operate any appliance which has a
battery, the trimmer should be recharged for
damaged output cord or housing.
16 hours approximately every 3 months.
4. Always unplug the unit before cleaning or
when not in use.
5. This power unit is intended to be correctly
oriented in a vertical or floor mount position.
6. Be sure voltage is in correct voltage before
plugging in.
USER MAINTENANCE THREE POSITION TAPER CONTROL
INSTRUCTIONS The Conair trimmer taper
control switch is positioned
at the back of the unit. You
TAkING CARE Of YOUR TRIMMER
can hold the trimmer in your
OILING THE BLADES
hand and adjust the switch
About once a month you should oil the
as needed. The taper control
trimmer blades with the oil provided in
eliminates the need in some situations for an
your kit. It is best to do this over a piece of
attachment comb because it lets you gradually
newspaper. Turn the trimmer on and hold it
adjust the closeness of the cut. For closest cut
so that the blades are pointed downward.
and shortest hair, push switch all the way to
Spread one drop of oil across the blades,
level #3. This is the setting to use for the 2
then turn the trimmer off and wipe away the
day shave look. To increase the cutting length,
excess oil with a soft cloth.
slowly push control down to level #2 or #1 for
Be careful not to use too much oil and don't
longer cut. Note that too much clipped hair on
oil your trimmer more than necessary, as this
the clipper can slow down its operation. To
could damage the motor. (Never attempt to
remove it without removing the blades simply
oil the motor bearing, as it is permanently
use a cleaning brush and gently sweep away
lubricated.) After oiling the blades, return the
the clipped hair from cutting surfaces. Note:
trimmer and oil packet to the storage pouch.
The taper control only works with the facial
Keep oil away from children.
hair trimmer.
BLADE CARE
GROwING A BEARD AND MUSTACHE
Because the trimmer blades are precision-
made for a very special use, they should
There are three key factors that will determine
always be handled with care. Each time you
which beard or mustache style is best for you:
finish using the trimmer, take a cleaning
1. The shape and dimensions of your face.
brush and brush away any loose hair that
2. The natural growth of your beard/mustache.
has collected in the blades. Then store the
3. The thickness of your beard/mustache. If
trimmer in its storage pouch to protect the
you are unsure about the type of beard or
blades until the next use.
mustache that would most suit your face,
Be especially careful when changing or
speak with a professional hair stylist and ask
adjusting attachments. When you have your
for an opinion on what style would be best.
trimmer serviced, be sure that blades are
Once your beard or mustache has been styled,
sharpened or replaced at the same time.
it is essential that you maintain its appear-
To promote the long life of the appliance, use
ance. To do this, use your trimmer to trim your
your trimmer only for the purpose intended
beard/mustache weekly.
by the manufacturer – to trim your beard and
For the best trimming results, your beard
mustache.
should be slightly damp (NOT WET) when even strokes. Start with
your sideburns and work
using your trimmer. This will prevent the trim-
downward toward your
mer from removing more hair than desired.
chin. (Never attempt to trim
TYPES Of BEARDS/MUSTACHES
against the natural growth of
your beard because the hair
will be cut too short.)
4. If you decide you want a
closer trim, you can now adjust
GETTING STARTED
the 5-position comb attach-
ment to a shorter setting (such
OUTLINING YOUR BEARD
as 3/32" or 5/32") and go over your beard again
1. It is always best to begin with a clean,
until you achieve the desired length.
slightly damp beard.
2. After you have combed through your beard HOw TO GET THE STUBBLE LOOk
in the direction it grows naturally, you will
This trimmer includes 2 stubble combs. These
want to outline the desired shape, beginning
combs allow you to achieve 6 different looks of
under your jawline.
stubble or shadow looks to your already exist-
3. Begin defining your beard's
ing growth. Simply use comb #2 or #4 for the
shape under your chin and
look you would like to achieve. You can also
work upward on each side of
use the taper control, which has 3 settings.
your face toward your ears.
Combined with 2 total stubble combs you can
Then define the upper outline of your beard
achieve your 6 different looks. Each comb has
across your cheeks, past your sideburns, and
a different length to custom a different look
toward your hairline.
each day! The stubble combs fit on the blade
NOw YOU'RE READY TO TRIM
just like the jawline combs, note blending the
YOUR BEARD
jawline section for specifics on how combs/
jawline combs go on.
1. The trimmer includes a five position comb
BLENDING THE JAwLINE
for use with the hair trimming blade (2-10mm)
which provide lengths of 3/32" (shortest) to
1. The two jawline attachments will help you to
3/8" (longest).
achieve a neat, finished trim under your chin. To
2. To use the 5-position comb, slide the unit
use one of the attachments, press it down over
over the trimmer blades and snap it down into
the trimmer blades until it clicks into position.
position. At first, until you become familiar with
2. Hold the trimmer in an upright position and
the adjustments, use the longest trim setting.
begin trimming under your jawline, using short,
(You can always go back and make your beard a
even strokes.
little shorter.)
3. After your beard is blended, turn off the
3. Begin trimming your beard using smooth,
trimmer and remove the attachment by gently
pulling up on tab.
TO TRIM YOUR MUSTACHE
1. For best results, start with a clean, slightly
damp mustache.
2. Comb through your mus-
tache in the direction it grows.
3. Place the 5-position comb
over the facial hair blade and
snap it into position. It is a good idea to start
with the longest trim setting adjustment. (You
can always go back and cut your mustache
more closely with a shorter setting.)
ALwAYS TRIM YOUR MUSTACHE
fROM THE TOP DOwN
4. After your mustache has
been trimmed to the desired
length, remove the 5-position
comb and, using the blades
only, define the outline of the bottom of your
mustache.
ROTARY NOSE & EAR TRIMMER
For easy, safe grooming of long nose and ear
hairs, attach the rotary nose/ear trimmer and
hold unit to areas that need trimming.
1. Make sure the trimmer on/off switch is in the
"off" position
2. Detach normal trimming blade (see "Replace-