1. Manuals
  2. Brands
  3. Conair Manuals
  4. Electric Shaver
  5. GMT180WRNCSC
  6. Instruction booklet

Conair GMT180WRNCSC Instruction Booklet

Cordless rechargeable beard & mustache trimmer
Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
to trIm your muStache
1. For best results, start with a clean, slightly damp
mustache.
2. Comb through your mustache in the direction
it grows.
3. Place the 5-position comb over the trimmer
blades and snap it into position. It is a good idea to
start with the longest trim setting adjustment. (You
can always go back and cut your mustache more
closely with a shorter setting.)
alwayS trIm your muStache
from the top down
4. After your mustache has been trimmed to the
desired length, remove the 5-position comb and,
using the blades only, define the outline of the
bottom of your mustache.
care of your trImmer
replacement (removal)
of blade Set
To remove blade set from your
trimmer, make sure the trimmer
is in the OFF position. Remove
the blade set by placing thumb
against the smaller cutter and
pushing forward, releasing the
cutter assembly from the trimmer
housing. Replace with new cutting system and
reverse the removal procedure, only this time
place your thumb on the large cutter and snap
into place.

Advertisement

Table of Contents
loading

Related Manuals for Conair GMT180WRNCSC

Summary of Contents for Conair GMT180WRNCSC

  • Page 1 care of your trImmer to trIm your muStache replacement (removal) 1. For best results, start with a clean, slightly damp of blade Set mustache. 2. Comb through your mustache in the direction To remove blade set from your it grows. trimmer, make sure the trimmer 3.

  • Page 2: Important Safety Instructions

    4. Never operate the appliance if it has a dam- aged cord or plug, is not working properly, has water been dropped or damaged, or dropped into water.Return the appliance to a Conair service DaNGer– centre for examination and repair. any appliance is electrically 5.

  • Page 3: Battery Removal

    CONTAINS NICKEL CADMIUM multI-uSe groomIng SyStem BATTERY. MUST BE COLLECTED, RECYCLED OR DISPOSED OF PROPERLY. DO NOT DISPOSE OF IN Cutter Blades THE MUNICIPAL WASTE. Blades Set 1. Using a small Phillips head screwdriver, remove the screw at the back of the trimmer.

  • Page 4: Troubleshooting

    for houSehold uSe only damage the trimmer. troubleShootIng 6. The charging stand may become warm while charging. This is normal. If your rechargeable trimmer does not seem to be taking a charge, take the following troubleshoot- Preserving the batteries: ing steps before returning it for repair: In order to maintain the optimum capacity of 1.
  • Page 5 SERVICE CENTRE: Conair Consumer Products Inc. 100 Conair Parkway, Woodbridge, Ontario, L4H 0L2. 1-800-472-7606 ©2009 Conair Consumer Products Inc. www.conaircanada.ca Consumer Call Centre E-mail : Consumer_Canada@Conair.com 09CN12705 IB-9087...

  • Page 6: Getting Started

    Be especially careful when changing or adjusting be slightly damp (NOT WET) when using your blades. When you have your trimmer serviced, be trimmer. This will prevent the trimmer from sure that both blades are sharpened or replaced removing more hair than desired. at the same time.
  • Page 7 1-800-472-7606 or visit us online at www.conaircanada.ca Model GMT180WRNCSC Instruction Booklet...
  • Page 8 downward toward your chin. (Never attempt to trim against the natural growth of your beard because the hair will be cut too short.) 4. If you decide you want a closer trim, you can now adjust the 5-position comb attachment to a shorter setting (such as 1/2”...

Table of Contents