Conair GMT235WCHC Instruction Booklet

Comb IN
PUSH
fig. A Comb OUT
PUSH
to 5/8" (longest).
2. To use the 5-position comb, slide it over the trimmer
blades and snap it down into position (fig.A). At first,
until you become familiar with the adjustments, use
the longest trim setting (5/8"). (You can always go
back and make your beard a
little shorter.)
3. This will give you the longest
"cut", for shorter "cuts" , place
thumb on the center of the top
of the cutting guide, pushing
forward to obtain 1/8"-5/8"
(see fig. B).
Your GMT235WCHC comes with an optional 5-posi-
tion pivoting head. This feature allows you to trim
those hard to reach facial contours. To use this
feature:
1.) Pick up your GMT235WCHC with the front of the trim-
mer facing you. Using your other hand simply push in
at the bottom of the upper head. Push in and set the
head to one of the settings (the unit comes prepack-
aged at the first setting, you then have four other
settings you can adjust your trimmer to). It will take
some time to get used to your own personal setting so
try each one until you find what works for you. As you
try these settings you will feel how comfortable this
makes trimming your beard or mustache.
2.) If you do not wish to use this
feature just leave the trimmer as
it was when it came out of the
package.
3.) Begin trimming your beard using
smooth, even strokes. Start with
your sideburns and work downward toward your
chin. (Never attempt to trim against the natural
growth of your beard because the hair will be cut
too short.)
4.) If you decide you want a closer trim, you can now
adjust the 5-position comb attachment to a shorter
setting and go over your beard again until you achieve
the desired length.
blendIng
tHe
JawlIne
1. The three jawline
attachments will help you to achieve a neat, finished
Adjustable Length:
Comb I -3mm trim under your chin. To use one of the attachments,
- 6mm
- 9mm
-12mm
press it down over the trimmer blades until it clicks
-15mm
Comb II -3mm
into position.
- 6mm
- 9mm
-12mm
2. Hold the trimmer in an upright position and begin
-15mm
fig. B
trimming under your jawline, using short, even
strokes.
3. After your beard is blended, turn off the trimmer and
remove the attachment by gently pulling up on tab.
to trIm
muStacHe
1. For best
with
damp mustache.
2. Comb through your mustache in the direction
it grows.
3. Place the 5-position comb over the trimmer blades
and snap it into position. It is a good idea to start with
the longest trim setting adjustment. (You can always
go back and cut your mustache more closely with a
shorter setting.)
alwayS trIm your muStacHe
4. After your mustache has been trimmed to the desired
length, remove the 5-position comb and, using the
blades only, define the outline of the bottom of your
mustache.
This versatile trimmer comes with 4 heads so facial
I
II
your
results, start
a clean, slightly
from tHe top down
hair styles can be changed as often as you like. It
also has a special taper control feature, which allows
you to have the 2 day shave look 365 days a year. To
achieve this look, simply put your trimmer blade to the
lowest setting.
Other great features include a small shaver head for
precise facial detailing on sideburns and goatees. A
wide facial hair blade with two 5-position adjustable
combs makes beard and mustache trimming quicker
and easier. The small detailing blade works for creating
III
"soul patches" as well as a nose and ear hair trimmer.
Congratulations on owning a great, new professional
grade trimmer.

battery removal

CONTAINS NICKEL CADMIUM
BATTERY. MUST BE
COLLECTED, RECYCLED OR
DISPOSED OF PROPERLY.
DO NOT DISPOSE OF IN
THE MUNICIPAL WASTE.
1. Using a small Phillips head screwdriver, remove
the screws at the bottom of the trimmer.
2. Remove the battery cap and push the battery out.
Bring the battery to the nearest collection center
for proper disposal. DO NOT throw the battery into
the normal municipal waste system.
BATTERY REMOVAL
SCREWS
CUTTING
POSITION