Remember Function; Two Clean Steps Function; Water Level Setting; Child Lock Function 1 - Zanussi ZTL75 User Manual

VARIOUS FUNCTIONS
PRESET
1. Press POWER ON/OFF button and make sure to fit the Drain Hose.
2. Turn the faucet on and load the laundry into the washer.
3. Select your needed OURSE, PROCESS and WATER LEVEL. C
4. Press PROCESS button till light of PRESET flashes, press SET button select your
needed preset time ( the time washing finished).
PRESET Indicate
6 7 8 ...... 24
5. Press START/PAUSE button.
6. Put the detergent and close washer lid.
● All the lights except PRESET will be lighted off in about one minute later.
● PRESET confirming: Press SET button to indicate PROCESS about 5 seconds.
● PRESET cancel, change: PRESET is canceled automatically when power off;
Switch power on and set PRESET again to change it.
● This function is not available for DELICATE course.
BLANKET
1.Press POWER ON/OFF button and open the washer lid.
2.Press COURSE button continuously and choose the BLANKET course (The BLANKET
Light flashes).
3.After the detergent is dissolved with proper amount of warm water (approx. 30 ), pour
it into the tub of the washing machine.
4.Fold up the blanket as the method showed in the figures below and put it into the
washing tub.
5.Close the washer lid.
6.Press the START/PAUSE button.
Fold in two by the Fold 4 times in the
long side same direction

REMEMBER FUNCTION

When select NORMAL, CUSTOM or HEAVY , after finishing the working,
the machine will remember this program and starts same next time working.
●This function is not available for DELICATE/BLANKET course.
●PRESET and WATER LEVEL will not be remembered.
●The soak, wash, Rinse and spin tor CUSTOM program could be remembered.
●The memory will be lost if pull out the plug.
10
0 1 ...... 5(hours)
℃
Roll up the blanket. Put it into the wash tub with
the edge downwards
VARIOUS FUNCTIONS

TWO CLEAN STEPS FUNCTION

The washer will start washing when water to the level below 2 levels as set. By this,
the washer starts working with more density of detergent.
· This function won't be available when select level 1 or level 2 water, and DELICATE
or BLANKET course.
· When SOAK is selected, this function will be available after soaking.
HYDROSINIC
HYDROSINIC is a built in function, when washing program starts, the light of
flashes. The washer will bring HYDROSINIC
washing and saving detergents
●
Please use less detergents or wash powder if you use

WATER LEVEL SETTING

This button allows you to choose the appropriate water level during WASH/RINSE process.
Method:
Press COURSE till WASH light flashes, press WATER LEVEL button to choose the
appropriate water level, press SET button to set wash time. Then press COURSE button
till RINSE light flashes, press WATER LEVEL button to choose the appropriate water level,
press SET button to set RINSE times and RINSE type. Then press COURSE button till
SPIN light flashes, press SET button to set SPIN time. Finally press START/PAUSE,
the washer will start operating according to the wash water level and rinse water level as
set.
CHILD LOCK FUNCTION
Press POWER ON/OFF button to switch on the power, and press TEMP button and
WATER LEVEL button for 4 seconds till a sound from buzzer. To restore it, repeat above or
pull out the plug.
When CHILD LOCK was set, the CHILD LOCK on control panel lights, and indicates E5
and buzzes if washer lid open for 5 seconds during washing.
DELETE THE END BUZZER
If select this function, the buzzer will not sound at the end of working. This is suitable for
washing clothes at night.
Method of setting
Press POWER ON/OFF button to switch on the power, and press START/PAUSE button
for 4 seconds till a sound from buzzer. To restore it, repeat above or pull out the plug.
HYDROSINIC
during working, and this helps more clean
HYDROSINIC function.
11