WARNING TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Registration Information FCC Information Use the attached speciﬁ ed cables with the MultiSync E224Wi (L222VW)/MultiSync E243WMi (L243QP) color monitor so as not to interfere with radio and television reception. The power supply cord you use must have been approved by and comply with the safety standards of U.S.A., and meet the following condition.
The product is intended to be connected to a computer and is not intended for the display of television broadcast signals. Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation. ErgoDesign is a registered trademark of NEC Display Solutions, Ltd. in Austria, Benelux, Denmark, France, Germany, Italy, Norway, Spain, Sweden, U.K.
For example, if an image was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image. NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for the display to warm up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eyes should look slightly downward when viewing the middle of the screen.
Contents Your new NEC LCD monitor box* should contain the following: • LCD monitor with tilt base • Power Cord • Video Signal Cable (DVI-D to DVI-D cable) • Video Signal Cable (15-pin mini D-SUB male to 15-pin mini D-SUB male) •...
To connect the LCD monitor to your system, follow these instructions: NOTE: Make sure to read “Recommended Use” (page 4) before installation. 1. Turn off the power of your computer. 2. For a PC or MAC with DVI digital output: Connect the DVI signal cable to the connector of the display card in your system (Figure A.1).
5. To keep the cables neatly organized, place them into the cable management system that is built into the stand. Place the cables in the hooks ﬁ rmly and evenly (Figure C.2 and Figure C.3). NOTE: Cable cover is not removable. 6.
Raise and Lower Monitor Screen The monitor may be raised or lowered in either portrait or landscape mode. To raise or lower screen, place a hand on each side of the monitor and lift or lower to the desired height (Figure RL.1). NOTE: Handle with care when raising or lowering the monitor screen.
Flexible Arm Installation This LCD monitor is designed for use with a ﬂ exible arm. To prepare the monitor for alternate mounting purposes: • Follow the instructions provided by the manufacturer of the display mount. • To meet the safety requirements, the mounting stand must be able to support the weight of the monitor and be UL-certiﬁ ed. Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes: 1.
Mount Flexible Arm This LCD monitor is designed for use with a ﬂ exible arm. 1. Follow the instructions on how Remove Monitor Stand for Mounting to remove the stand. 2. Use the 4 screws removed from the stand to attach the arm to the monitor (Figure F.1). Caution: Use ONLY the screws (4 pcs) that were removed from the stand to avoid damage to the monitor or stand.
Controls OSD (On-Screen Display) Control Functions 1. Basic functions of the touch keys on the front of the monitor – INPUT/RESET SELECT OSD Menu Not displaying on screen Selects input signal. Displays OSD. Shortcut to Brightness. Shortcut to Contrast (E224Wi). Shortcut to Volume (E243WMi).
AUDIO (E243WMi only) Controls the volume of the speakers or headphones. To mute the speaker output, select Audio icon and touch “INPUT/RESET”. BRIGHTNESS Adjusts the overall image and background screen brightness. To enter the ECO MODE, touch the “INPUT/RESET” button. ECO MODE OFF: Sets brightness variable from 0% to 100%.
EXIT Selecting EXIT allows you exit OSD menu/ sub menu. TOOL EXPANSION Selects the zoom mode. This function works, when input signal timing is under native resolution. FULL: The image is expanded to full screen, regardless of the resolution. ASPECT: The image is expanded without changing the aspect ratio. RESPONSE IMPROVE Turns the Response Improve function on or off.
OSD Warning OSD Warning menus disappear by touching SELECT. NO SIGNAL: This function gives a warning when there is no signal present. After power is turned on or when there is a change of input signal or video is inactive, the NO SIGNAL window will appear. OUT OF RANGE: This function gives a recommendation of the optimized resolution and refresh rate.
60 Hz to 75 Hz 1440 x 900* at 60 Hz 1680 x 1050* at 60 Hz 1920 x 1080 at 60 Hz........... NEC DISPLAY SOLUTIONS cites recommended resolution for optimal display performance. Active Display Area Landscape: Horiz.: 476.1 mm/18.7 inches Vert.:...
60 Hz to 75 Hz 1440 x 900* at 60 Hz 1680 x 1050* at 60 Hz 1920 x 1080 at 60 Hz........... NEC DISPLAY SOLUTIONS cites recommended resolution for optimal display performance. Active Display Area Landscape: Horiz.: 527.0 mm/20.7 inches Vert.:...
Note: The manufacturing and operating carbon footprints are calculated by a unique algorithm developed exclusively by NEC for its monitors and are accurate at the time of printing. NEC reserves the right to publish updated carbon footprint values. HDCP (High-bandwidth Digital Content Protection): HDCP is a system for preventing illegal copying of video data sent over a Digital Visual Interface (DVI).
NOTE: As with all personal display devices, NEC DISPLAY SOLUTIONS recommends using a screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use. Message “OUT OF RANGE” is displayed (screen is either blank or shows rough images only) •...
TCO Certiﬁ ed Displays 6 Congratulations! This product is TCO Certiﬁ ed – for Sustainable IT TCO CertiÞ ed is an international third party sustainability certiÞ cation for IT products. TCO CertiÞ ed ensures that the manufacture, use and recycling of IT products reß ect environmental, social and economic responsibility.
Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life.