Brake Noise; Permanent Modification To Lower Ball Joints; Brake Vibration - StopTech ST-40 Caliper Installation Instructions Manual

355mm front big brake upgrade for corvette c5 1997 - 2004
Table of Contents

Advertisement

APPLICA
APPLICA
APPLICATION DISCL
APPLICA
APPLICA
B B B B B rake N
rake N
rake N
oise
oise
rake N
rake Noise
oise
oise
Certain brake pad compounds make more noise than others. Proper anti-squeal shim plates be-
tween the caliper pistons and backing plate of the pad help to reduce the problem. Anti-squeal
lubricants are also available, to reduce some of the noise. The reality is that performance pads are
more prone to brake squeal.
Note: The customer is responsible for any squeal-related problems due to pad selection.
Note: The customer is responsible for any squeal-related problems due to pad selection.
Note: The customer is responsible for any squeal-related problems due to pad selection.
Note: The customer is responsible for any squeal-related problems due to pad selection.
Note: The customer is responsible for any squeal-related problems due to pad selection.
P P P P P er er er er ermanent M
manent M
manent M
manent Modification to Lo
manent M
odification to Lo
odification to Lo
odification to Lo
odification to Low w w w w er B
It may be necessary to grind a portion of each lower ball joint, to clear the inboard face of the rotor
during full suspension travel. If done carefully, this modification will not affect the strength or
structural integrity of the vehicle. Although a coarse file will remove the material, a power grinder,
if used properly, will be more efficient. If you are uncomfortable making this modification, seek
the help of a qualified professional.
B B B B B rake
rake
rake
Vibration -
Vibration -
rake
rake Vibration -
Vibration -
Vibration - THIS IS IMPOR
The most common cause of brake vibration is improper bed-in of pads and rotors, or improper pad
selection for the specific driving environment. Rotor run-out may also cause vibration, but preci-
sion manufacturing and inspection typically mean that run-out is not an issue. Modern produc-
tion methods ensure that the rotor run-out is within +/- 0.002" when installed on a StopTech alumi-
num hat, and it controls thickness variation to within 0.0003". Under the most extreme conditions,
any rotor may warp, but uneven pad deposition is a more typical cause of vibration. If the system
is not properly bedded-in, or if street pads are run on an open track, uneven pad deposits will occur,
causing an ever-worsening vibration. Failure to immediately address a pad deposition/vibration
issue may lead to permanent damage of the rotors. Please read and understand the bed-in proce-
dure included in this manual. If you have any questions, please contact the StopTech Customer
Service Department on (310) 325-4799 - extension 105, or you can e-mail directly to
support@stoptech.com
support@stoptech.com.
support@stoptech.com
support@stoptech.com
support@stoptech.com
N N N N N ote: S
ote: S
ote: StopT
ote: S
topT
topT
topTech is not liable for vibr
ech is not liable for vibr
ech is not liable for vibrations caused by e
ech is not liable for vibr
ote: S
topT
ech is not liable for vibr
pads and rotors.
pads and rotors.
pads and rotors.
pads and rotors.
pads and rotors.
All trademar
All trademar
ks ar
ks ar
e pr
e pr
All trademar
All trademarks ar
All trademar
ks ar
ks are pr
e pr
e proper
ated nor affiliated with, nor sponsored by General Motors.
ated nor affiliated with, nor sponsored by General Motors.
ated nor affiliated with, nor sponsored by General Motors.
ated nor affiliated with, nor sponsored by General Motors.
ated nor affiliated with, nor sponsored by General Motors.
3541 Unit A, Lomita Boulevard, Torrance, CA 90505 (310) 325-4799
TION DISCLAIMER (Cont
TION DISCL
TION DISCL
TION DISCL
er B
er B
er B
er Ball J
THIS IS IMPOR
THIS IS IMPORT T T T T ANT!
THIS IS IMPOR
THIS IS IMPOR
ations caused by e
ations caused by extr
ations caused by e
ations caused by e
oper
oper
ties of their r
ties of their r
espectiv
espectiv
oper
operties of their r
ties of their r
ties of their respectiv
espectiv
espective o
www.stoptech.com
AIMER (Cont' ' ' ' ' d.)
AIMER (Cont
AIMER (Cont
AIMER (Cont
all Joints
all J
all J
all J
oints
oints
oints
oints
ANT!
ANT!
ANT!
ANT!
xtr
xtr
xtreme usage or impr
eme usage or impr
eme usage or improper bed-in of
eme usage or impr
xtr
eme usage or impr
e o
e o
wners. S
wners. S
topT
topT
ech LL
ech LL
e o
e owners. S
wners. S
wners. StopT
topT
topTech LL
ech LLC is neither associ-
ech LL
d.)
d.)
d.)
d.)
oper bed-in of
oper bed-in of
oper bed-in of
oper bed-in of
C is neither associ-
C is neither associ-
C is neither associ-
C is neither associ-
4

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ST-40 Caliper and is the answer not in the manual?

Table of Contents

Save PDF