Install Aerorotor Assembly - StopTech ST-40 Caliper Installation Instructions Manual

355mm front big brake upgrade for corvette c5 1997 - 2004
Table of Contents

Advertisement

S S S S S tep 5
tep 5
tep 5
tep 5
tep 5

Install AeroRotor Assembly

Install AeroRotor Assembly
Install AeroRotor Assembly
Install AeroRotor Assembly
Install AeroRotor Assembly
MUST
MUST
AeroRotors MUST
MUST be cleaned with soap and water prior to installation. Not doing so will damage
MUST
the rotors and pads, and will prevent the brakes from performing properly.
Install the hat and rotor assembly, ensuring that
the rotor is seated squarely on the hub face. If
necessary, clean the face of the hub, using a wire
brush or similar means.
Place a couple of wheel nuts on the studs, to pre-
vent the rotor from falling during brake installa-
tion.
N N N N N ote: T
ote: T
ote: T
ake car
ake car
e to ensur
e to ensur
ote: T
ote: Take car
ake car
ake care to ensur
e to ensur
e to ensure that the r
the rotors will severely decrease the cooling capacity of the system. The rotors are clearly
the rotors will severely decrease the cooling capacity of the system. The rotors are clearly
the rotors will severely decrease the cooling capacity of the system. The rotors are clearly
the rotors will severely decrease the cooling capacity of the system. The rotors are clearly
the rotors will severely decrease the cooling capacity of the system. The rotors are clearly
mar
mar
mar
mar
marked "L
ked "L
ked "L
ked "L" and "R
ked "L
" and "R
" and "R
" and "R" with or
" and "R
" with orange tags on the r
" with or
" with or
" with or
inside the rotor should lean to the rear of the car on the top side of the rotor (see pages 13
inside the rotor should lean to the rear of the car on the top side of the rotor (see pages 13
inside the rotor should lean to the rear of the car on the top side of the rotor (see pages 13
inside the rotor should lean to the rear of the car on the top side of the rotor (see pages 13
inside the rotor should lean to the rear of the car on the top side of the rotor (see pages 13
and 14 for more-detailed images).
and 14 for more-detailed images).
and 14 for more-detailed images).
and 14 for more-detailed images).
and 14 for more-detailed images).
3541 Unit A, Lomita Boulevard, Torrance, CA 90505 (310) 325-4799
e that the r
e that the r
otor assembly is on the corr
otor assembly is on the corr
e that the r
e that the rotor assembly is on the corr
otor assembly is on the correct side of the car
otor assembly is on the corr
ange tags on the rotor hats. If the tags ar
ange tags on the r
ange tags on the r
ange tags on the r
www.stoptech.com
Even though the rotors may look clean, the rust
inhibitor is in place, and it must be removed.
Not cleaning the rotors will severely impact the
performance of your new brake system.
W W W W W ar ar ar ar arning: D
ning: D
ning: D
ning: Do not skip this step!
ning: D
o not skip this step!
o not skip this step!
o not skip this step!
o not skip this step!
ect side of the car
ect side of the car
ect side of the car, as r
ect side of the car
otor hats. If the tags ar
otor hats. If the tags ar
otor hats. If the tags ar
otor hats. If the tags are not legible, the v
, as rev ev ev ev eversing
, as r
, as r
ersing
ersing
, as r
ersing
ersing
e not legible, the v
e not legible, the v
e not legible, the vanes
e not legible, the v
anes
anes
anes
anes
11

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ST-40 Caliper and is the answer not in the manual?

Table of Contents

Save PDF