Related Manuals for Kenwood C-BX3
Summary of Contents for Kenwood C-BX3
-
Page 1: Instruction Manual
COMPACT HI-FI COMPONENT SYSTEM C-BX3 INSTRUCTION MANUAL Glass inside GVT0349-001A [E] © 2012 JVC KENWOOD Corporation... -
Page 2: Warnings, Cautions And Others
• Do not drag or push the main unit/stand base on the floor or table. Otherwise the foot spacers at the bottom of the main unit/stand base may peeled off or drop. C-BX3... -
Page 3: Table Of Contents
3-12, Moriyacho, Kanagawa-ku, Yokohama-shi, Kanagawa, 221-0022, Japan Getting started ......5 EU Representative's: Unpacking and assembling the Kenwood Electronics Europe BV system ................5 Amsterdamseweg 37, 1422 AC UITHOORN, Placing the system ........... 5 The Netherlands About measures to prevent falling down and toppling over ........ -
Page 4: Introduction
Stains on the System should be wiped off with a soft cloth. If the System is heavily stained, wipe it with a cloth soaked in water diluted neutral detergent and wrung well, then wipe clean with a dry cloth. C-BX3... -
Page 5: Part List And Supplied Accessories
Getting started • Since the System may deteriorate in quality, become damaged or get DO NOT connect the power cord until all other its paint peeled off, be careful about the following: connections have been made. – DO NOT wipe it forcefully. –... -
Page 6: About Measures To Prevent Falling Down And Toppling Over
Do not poke the battery with tweezers or similar tools. • Dispose of the battery in the proper manner, according to federal, state, A: 2-3 mm and local regulations. B: Minimum φ11 mm (screw head diameter) C: φ4 mm (screw diameter) D: Minimum 20 mm C-BX3... -
Page 7: Setting The Video Output
Using the core filter Setting the video output While the source is selected to IPOD and iPod is not connected to the To reduce interference, be sure to attach the provided core filters to the unit... power cord and the external component cord. Press and hold iPod 6 (main unit). -
Page 8: Connecting The Dc Power Cord
When iPod is not connected to the unit. • To avoid the risk of fire and to prevent damage, – Do not use any AC adaptors other than the one supplied. – Do not use the supplied AC adaptor for other equipment. C-BX3... -
Page 9: Selecting The Input Source
When one of the situations occurs... ⁄ The APS indicator is shown for 1 second every 1 minute and starts The change in the bass and treble sound level of the speakers differ flashing 30 seconds before the System turns off. depending on the incoming signal of the input source. -
Page 10: Buttons And Lamps On The Front
Push the tray to open the dock for iPod. 5 VOLUME +/– buttons 9 Display Adjusts the volume within the range of 0 (MIN) to 40 (MAX). Shows the volume level, the current source and the settings. 6 Remote sensor Receives the signal from the remote control. C-BX3... -
Page 11: Troubleshooting
Troubleshooting Specifications If you have a problem with this System, check this list for a possible Output Power : 30 W + 30 W RMS (1 kHz, 10% T.H.D., 4 Ω) solution before calling for service. Audio section Power Input Terminals : ANALOG IN : 1 V/50 kΩ Power does not come on. - Page 12 • is a trademark of SRS Labs, Inc. • StudioSound HD technology is incorporated under license from SRS Labs, Inc. • SSHD: StudioSound HD by SRS Labs, Inc. SRS StudioSound HD™ provides an immersive and engaging surround sound experience, while maintaining steady volume and delivering rich bass and clear dialog.
Need help?
Do you have a question about the C-BX3 and is the answer not in the manual?
Questions and answers