Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for InFocus IN8606HD
Summary of Contents for InFocus IN8606HD
- Page 2 Adobe Systems Incorporated. DLP®, DLP Link and the DLP logo are registered trademarks of Texas Instruments and BrilliantColor™ is a trademark of Texas Instruments. InFocus, In Focus, and INFOCUS (stylized) are either registered trademarks or trademarks of InFocus Corporation in the United States and other countries.
-
Page 3: Important Safety Information
IN8606HD User’s Manual Important Safety Information Important: It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector. Keep this manual for future reference. -
Page 4: Projector Installation Notice
Preface Projector Installation Notice Place the projector in a horizontal position The tilt angle of the projector should not exceed 15 degrees. In addition, the projector should not be installed in any other way except desktop and ceiling mount positions. Otherwise lamp life could decrease dramatically, and may lead to other unpredictable damage. -
Page 5: About This Manual
IN8606HD User’s Manual Power Safety Only use the supplied power cord. Do not place anything on the power cord. Place the power cord where it will not be in the way of foot traffic. Remove the batteries from the remote control when storing or not in use for a prolonged period. -
Page 6: Table Of Contents
Preface Table of Contents GETTING STARTED................................1 ................................1 ACKING HECKLIST ............................... 2 IEWS OF ROJECTOR ARTS Front-right View ................................2 Top view—On-screen Display (OSD) buttons and LEDs..................3 Rear view..................................4 Bottom view................................... 6 ..............................7 EMOTE ONTROL ARTS .......................... - Page 7 IN8606HD User’s Manual SPECIFICATIONS ................................46 ................................. 46 PECIFICATIONS ........................47 ROJECTION ISTANCE VS ROJECTION Projection Distance and Size Table......................... 47 ................................ 48 IMING ABLE ..............................50 ROJECTOR IMENSIONS REGULATORY COMPLIANCE............................51 FCC W .................................. 51 ARNING .................................... 51 ANADA ..............................
-
Page 8: Getting Started
IN8606HD User’s Manual ETTING TARTED Packing Checklist Carefully unpack the projector and check that the following items are included: DLP P ROJECTOR WITH HDMI EMOTE CONTROL CABLE OWER CORD ATTERIES NOT INCLUDED CD-ROM UICK TART UIDE ARRANTY ’ S MANUAL Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. -
Page 9: Views Of Projector Parts
IN8606HD User’s Manual Views of Projector Parts Front-right View 2 3 4 5 ABEL ESCRIPTION EE PAGE IR receiver Receive IR signal from remote control Lens Projection Lens Focus ring Focuses the projected image Zoom ring Enlarges the projected image See Top view—On-screen Display (OSD) buttons... -
Page 10: Top View-On-Screen Display (Osd) Buttons And Leds
IN8606HD User’s Manual Top view—On-screen Display (OSD) buttons and LEDs ABEL ESCRIPTION EE PAGE Turns the projector On and Off Lamp Failure LAMP LED Blinking Red Error code Projector is in standby or is fully Blue powered on (lamp is lit). -
Page 11: Rear View
IN8606HD User’s Manual Rear view 3 4 5 6 ABEL ESCRIPTION EE PAGE AC IN Connect a POWER cable Connect the 3D IR glasses transmitter 3D SYNC (Note: For Specific 3D IR glasses only) HDMI 1 Connect an HDMI cable from a HDMI device... - Page 12 IN8606HD User’s Manual DC12V Trigger Note: To use this feature, you must plug in the connector before turn on/off the projector. Screen controllers are supplied and supported by screen manufacturers. Do not use this jack for anything other than intended use.
-
Page 13: Bottom View
Refer to the installation guide that comes with the InFocus Ceiling Mount kit for more information. The warranty does not cover any damage caused by use of non-approved ceiling mount kits or by installing in an improper location. -
Page 14: Remote Control Parts
IN8606HD User’s Manual Remote Control Parts Important: 1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the remote control and the projector. If the path between the remote control and the projector is obstructed, you can bounce the signal off certain reflective surfaces such as projector screens. - Page 15 IN8606HD User’s Manual ABEL ESCRIPTION EE PAGE Navigates up and changes settings in the OSD Enter Changes settings in the OSD Power Turns the projector on or off Right Navigates to the right and changes settings in the OSD Volume +...
-
Page 16: Remote Control Operating Range
IN8606HD User’s Manual Remote Control Operating Range The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and 15 degrees above or below the projector level. -
Page 17: Setup And Operation
1. Only use a 3V lithium battery (CR2025). 2. Dispose of used batteries according to local ordinance regulations. 3. Remove the batteries when not using the projector for prolonged periods. Note: Batteries are not normally included with InFocus projectors. –10 –... -
Page 18: Turning The Projector On And Off
IN8606HD User’s Manual Turning the projector on and off Connect the power cord to the projector. Connect the other end to a wall outlet. POWER LED on the projector light. Turn on the connected devices. Ensure the POWER LED is not flashing. - Page 19 IN8606HD User’s Manual To turn the projector off, press the POWER button. When the “Power Off? Press Power again” message appears, press the POWER button. The projector turns off. Caution: 1. Be sure to remove the lens cap before starting projector.
-
Page 20: Setting An Access Password (Security Lock)
Keep the password in a safe place. Without the password, you will not be able to use the projector. If you lose the password, contact InFocus Support for information on clearing the password. Press the MENU button to open the OSD menu. - Page 21 IN8606HD User’s Manual You can use the arrow buttons ▲▼◄► either on keypad or IR remote control for password entry. You can use any combination including the same arrow five times, but five characters must be used.. Press the arrow buttons in any order to set the password.
-
Page 22: Adjusting The Projector Level
IN8606HD User’s Manual Adjusting the Projector Level Take note of the following when setting up the projector: The projector table or stand should be level and sturdy. Position the projector so that it is perpendicular to the screen. -
Page 23: Adjusting The Zoom, Focus And Keystone
IN8606HD User’s Manual Adjusting the Zoom, Focus and Keystone Use the Image-zoom control (on the projector only) to resize the projected image and screen size Use the Image-focus control (on the projector only) to sharpen the projected image Use the KEYSTONE... -
Page 24: On-Screen Display (Osd) Menu Settings
IN8606HD User’s Manual (OSD) M CREEN ISPLAY ETTINGS OSD Menu Controls The projector has an OSD that lets you make image adjustments and change various settings. Navigating the OSD You can use the remote control arrow buttons to navigate and make changes to the OSD. -
Page 25: Setting The Osd Language
IN8606HD User’s Manual Setting the OSD Language Set the OSD language to your preference before continuing. 1. Press the MENU button. Press the ◄► buttons to navigate to Settings 1. Press the ▲▼ buttons to move to the Advanced 1 menu. -
Page 26: Osd Menu Overview
IN8606HD User’s Manual OSD Menu Overview Use the following illustration to quickly find a setting or determine the range for a setting. – 19 –... -
Page 27: Image Menu
IN8606HD User’s Manual Image Menu Attention ! When image options are changed, the Display Mode changes to User. Press the MENU button to open the OSD menu. Press the ◄► buttons to move to the Image Menu. Press the ▲▼ buttons to move up and down in the Image menu. Press the ◄► buttons to enter and change setting values. -
Page 28: Computer Menu
IN8606HD User’s Manual Computer Menu Press the MENU button to open the OSD menu. Press the ◄► buttons to move to the Image menu. Press the ▲▼ buttons to move to the Computer menu and then press (Enter) or ►. Press the ▲▼... -
Page 29: Advanced Features
IN8606HD User’s Manual Advanced Features Press the Menu button to open the OSD menu. Press the ◄► buttons to move to the Image menu. Press the ▼▲ buttons to move to the Advanced menu and then press (Enter) or ►. Press the ▼▲... -
Page 30: White Balance
IN8606HD User’s Manual White Balance Press the (Enter) or ► button to enter the White Balance sub menu. Press ▼▲ to move up and down in the White Balance menu. ESCRIPTION R Gain Press the ◄► buttons to adjust the Red Gain. -
Page 31: Color Manager
IN8606HD User’s Manual Color Manager Press the Menu button to open the OSD menu. Press the ◄► buttons to move to the Image menu. Press the ▼▲ buttons to move to the Color Manager menu and then press (Enter) or ►. Press the ▼▲... -
Page 32: Settings 1 Menu
IN8606HD User’s Manual Settings 1 Menu Press the MENU button to open the OSD menu. Press the ◄► buttons to move to the Settings 1 menu. Press the ▲▼ buttons to move up and down in the Settings 1 menu. Press the ◄► buttons to enter and change setting values. -
Page 33: Audio
IN8606HD User’s Manual Audio Press the Menu button to open the OSD menu. Press the ◄► buttons to move to the Settings 1 menu. Press the ▼▲ buttons to move to the Audio menu and then press (Enter) or ►. Press the ▼▲... -
Page 34: Advanced 1 Features
IN8606HD User’s Manual Advanced 1 Features Press the Menu button to open the OSD menu. Press the ◄► buttons to move to the Settings 1 menu. Press the ▲▼ buttons to move to the Advanced 1 menu and then press (Enter) or ►. - Page 35 IN8606HD User’s Manual 3D Setting ESCRIPTION Press the ◄► buttons to enter and select different 3D modes. 3D Sync Invert Press the ◄► buttons to enter and enable or disable 3D Sync Invert. 3D Format Press the ◄► buttons to enter and enable or disable different 3D Format.
-
Page 36: Advanced 2 Features
IN8606HD User’s Manual Advanced 2 Features Press the Menu button to open the OSD menu. Press the ◄► buttons to move to the Settings 1 menu. Press the ▲▼ buttons to move to the Advanced 2 menu and then press (Enter) or ►. -
Page 37: Settings 2 Menu
IN8606HD User’s Manual Settings 2 Menu Press the MENU button to open the OSD menu. Press the ◄► buttons to move to the Settings 2 menu. Press the ▲▼ buttons to move up and down in the Settings 2 menu. -
Page 38: Status
IN8606HD User’s Manual Status Press the ▲▼ buttons to move up and down in the Settings 2 menu. Select the Status menu and press (Enter) or ► to enter. ESCRIPTION Active Source Displays the current active source type. Displays resolution/video information for RGB sources and color standard for Video Video Information sources. -
Page 39: Advanced 1 Features
IN8606HD User’s Manual Advanced 1 Features Press the Menu button to open the OSD menu. Press the ◄► buttons to move to the Settings 2 menu. Press the ▲▼ buttons to move to the Advanced 1 menu and then press (Enter) or ►. - Page 40 IN8606HD User’s Manual Lamp Hour Reset Please refer to Resetting the on page 38 to reset the lamp hour counter. – 33 –...
-
Page 41: Advanced 2 Features
IN8606HD User’s Manual Advanced 2 Features Press the Menu button to open the OSD menu. Press the ◄► buttons to move to the Settings 2 menu. Press the ▲▼ buttons to move to the Advanced 2 menu and then press (Enter) or ►. - Page 42 IN8606HD User’s Manual Source Filter Press the ENTER button to enter the Source Filter sub menu. This sub menu allows you to enable and disable source inputs. ESCRIPTION Press the ◄► buttons to enter and enable or disable the VGA1 source.
-
Page 43: Maintenance And Security
IN8606HD User’s Manual AINTENANCE AND ECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be replaced with a certified replacement part, which you can order from your local dealer. Important: a. The projection lamp used in this product contains a small amount of mercury. - Page 44 IN8606HD User’s Manual Remove the lamp compartment cover. Remove the three screws from the lamp module. Lift the module handle up. Pull firmly on the module handle to remove the lamp module. Reverse steps 1 to 5 to install the new lamp module.
-
Page 45: Resetting The Lamp Timer
IN8606HD User’s Manual Resetting the Lamp Timer After replacing the lamp, you should reset the lamp hour timer to zero. Refer to the following: Press the MENU button to open the OSD menu. Press the ◄► buttons to move to the Settings 2 menu. -
Page 46: Cleaning The Projector
IN8606HD User’s Manual Cleaning the Projector Cleaning the projector to remove dust and grime will help ensure trouble-free operation. Warning: 1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so could result in a severe burn. -
Page 47: Using The Cable Lock System And Security Bar
Note: A Cable Lock System can be purchased from InFocus or your dealer. Refer to the information that comes with the lock for instructions on how to use it. The security lock slot corresponds to Kensington’s MicroSaver Security System. If you have any comment, contact: Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A. -
Page 48: Troubleshooting
IN8606HD User’s Manual ROUBLESHOOTING Common problems and solutions These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains unsolved, contact your dealer for assistance. After spending time troubleshooting, the problem can often be traced to something as simple as a loose connection. -
Page 49: Led Error Messages
In the event of an error, please disconnect the AC power cord and wait for one (1) minute before restarting the projector. If the Power or Lamp LEDs are still blinking or any other situation that isn't listed in the chart above , please contact InFocus Support. Image Problems Problem: No image appears on the screen 1. -
Page 50: Lamp Problems
IN8606HD User’s Manual Problem: The image is wider at the top or bottom (trapezoid effect) 1. Position the projector so it is as perpendicular to the screen as possible. 2. Use the Keystone button on the remote control to correct the problem. -
Page 51: Audio Problems
3. Have the projector serviced. Having the Projector Serviced If you are unable to solve the problem, you should have the projector serviced. Pack the projector in the original carton and contact InFocus Support at www.infocus.com/support or call us. –44 –... -
Page 52: Hdmi Q & A
IN8606HD User’s Manual HDMI Q & A Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI cable? Recently, HDMI Licensing, LLC announced that cables would be tested as Standard or High- Speed cables. ˙Standard (or “category 1”) HDMI cables have been tested to perform at speeds of 75Mhz or up to 2.25Gbps, which is the equivalent of a 720p/1080i signal. -
Page 53: Specifications
Screen trigger: DC Jack x 1 (DC12V 200mA output function) USB (Type mini B) - service only USB (type A) support DC 5V Kensington lock / Security Bar Security Note: InFocus reserves the right to alter product offerings and specifications at any time without notice. –46 –... -
Page 54: Projection Distance Vs. Projection Size
IN8606HD User’s Manual Projection Distance vs. Projection Size Projection Distance and Size Table IN8606HD ROJECTION ROJECTION MAGE IAGONAL ISTANCE ISTANCE MAGE IDTH MAGE EIGHT FFSET （ ） （ ） （ ） INCH INCH INCH INCH INCH INCH 1524 / 60 1328.2 / 52.29... -
Page 55: Timing Mode Table
IN8606HD User’s Manual Timing Mode Table HDMI OMPOSITE IGNAL ESOLUTION OMPONENT ( KH VIDEO NALOG IGITAL NTSC 15.734 ○ － － － － PAL/SECAM 15.625 ○ － － － － 640 x 400 37.9 85.08 ○ ○ － － VESA 720 x 400 31.5... - Page 56 IN8606HD User’s Manual HDMI OMPOSITE IGNAL ESOLUTION OMPONENT ( KH VIDEO NALOG IGITAL 1280 x 1024 91.1 ○ ○ － － 1280 x 960 ○ ○ － － 1280 x 960 85.9 ○ ○ － － 1360 x 768 47.7 ○...
-
Page 57: Projector Dimensions
IN8606HD User’s Manual Projector Dimensions 285.1mm [11.22"] –50 –... -
Page 58: Regulatory Compliance
IN8606HD User’s Manual EGULATORY OMPLIANCE FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. -
Page 59: Serial Communication
IN8606HD User’s Manual PPENDIX Serial Communication The following table describes the serial communication configuration that should be used when interfacing to CLI via the serial port. Windows HyperTerminal or ProComm are two tools that can be used to send CLI commands across the serial port. - Page 60 IN8606HD User’s Manual Function Command Min Max Default Step Parameter Valid only when Display Mode = User Source Color Temp 0:Warm Specific 1:Normal 2:Cold Valid only when Display Contrast Mode = User 0:VGA1 5:HDMI-1 6:HDMI-2 Current Source 10:Component 12:Video 13:S-Video...
- Page 61 IN8606HD User’s Manual Function Command Min Max Default Step Parameter 0:English 1:French 2:German 3:Spanish 4:Portuguese 5:Simplified Chinese 6:Traditional Chinese 7:Italian 8:Norwegian 9:Swedish Language 10:Dutch 11:Russian 12:Finnish 13:Korean 14:Arabic 15:Turkish 16:Japanese 17:Brazilian Portuguese 18:Kazakh 19:Vietnamese 20:Danish Menu 0:Clear; 1:Display 0:Menu Key...
- Page 62 IN8606HD User’s Manual Function Command Min Max Default Step Parameter Displays the numbers of hours that the projector has Projector Low Power 9999 run in Low Power (Eco) Hours mode over its life (including all lamps). 118V Projector Model string...