Document Created by Nick Schuster...
D-Link DAP-2695 User Manual Table of Contents Product Overview ..............4 Wireless Resource Control ............26 Introduction ................... 4 Multi-SSID ................28 Features .................... 5 VLAN ..................30 Package Contents ................. 6 VLAN List ................30 System Requirements ..............6 Port List ................31 Add/Edit VLAN ...............32 Hardware Overview ..............7...
D-Link DAP-2695 User Manual Traffic Control................48 Configuration and System............67 Uplink/Downlink Setting ..........48 System Settings ................68 QoS...................49 Help ....................69 Traffic Manager ..............50 Knowledge Base ..............70 Status ....................51 Wireless Basics ................70 Device Information ............52 Wireless Installation Considerations ........71 Client Information ..............53 WDS Information Page .............54...
LAN segmentation, Disable SSID Broadcast, Rogue AP Detection, and Wireless Broadcast Scheduling are also included. The DAP-2695 includes support for up to 16 VLANs for implementing multiple SSIDs to further help segment users on the network. The DAP-2695 also includes a wireless client isolation mechanism, which limits direct client-to-client communication.
Environmental conditions will adversely affect wireless signal range. **Please note that operating frequency ranges vary depending on the regulations of individual countries and jurisdictions. The DAP-2695 isn’t supported in the 5.25~5.35GHz and 5.47 ~ 5.725GHz frequency ranges in...
• Console Cable • CD (with software and user manual) Note: Using a power supply with a different voltage rating than the one included with the DAP-2695 will cause damage and void the warranty for this product. System Requirements y Computers with Windows®, Macintosh®, or Linux-based operating systems with an installed Ethernet Adapter...
D-Link DAP-2695 User Manual Hardware Overview LEDs Connections When lit, the access point is operating at 5GHz. This light Press and hold for six seconds to reset the access point 5GHz Reset Button will blink when there is wireless traffic.
D-Link DAP-2695 User Manual Basic Installation Hardware Setup To power the access point, you can use one of the following 3 methods: Method 1 - Use if you have a PoE switch or router. Method 2 - Use if you do not have a PoE switch or router and do not have a power outlet near the location of the access point.
D-Link DAP-2695 User Manual Method 2 - PoE without PoE Switch or Router 1. Connect one end of an Ethernet cable into the Data In port on the PoE base unit and the other end into one port on your switch, router, or computer.
D-Link DAP-2695 User Manual Method 3 - No PoE 1. Connect one end of your Ethernet cable into the LAN1 (PoE) or LAN2 port and then connect the other end to a switch, router, or computer. 2. Use the supplied power adapter. Connect the power adapter to the Power receptor on the Access Point.
Web User Interface The DAP-2695 supports an elaborate web user interface where the user can configure and monitor the device. Most of the configurable settings are located in the left menu of the web GUI which contains section called Basic Settings, Advanced Settings and Status.
D-Link DAP-2695 User Manual Wireless On the wireless settings page, you can setup the basic wireless configuration for the access point. The user can choose from 4 different wireless modes: Access Point - Used to create a wireless LAN WDS with AP - Used to connect multiple wireless networks while still functioning as a wireless access point...
D-Link DAP-2695 User Manual Channel: To change the channel, first toggle the Auto Channel Selection setting to Disable, and then use the drop-down menu to make the desired selection. Note: The wireless adapters will automatically scan and match the wireless settings.
D-Link DAP-2695 User Manual WDS with AP Mode Wireless Band: Select either 2.4GHz or 5GHz from the drop-down menu. Mode: WDS with AP mode is selected from the drop-down menu. Network Name (SSID): Service Set Identifier (SSID) is the name designated for a specific wireless local area network (WLAN).
D-Link DAP-2695 User Manual Remote AP MAC Address: Enter the MAC addresses of the APs on your network that will serve as bridges to wirelessly connect multiple networks. Site Survey: Click on the Scan button to search for available wireless networks, then click on the available network that you want to connect with.
D-Link DAP-2695 User Manual WDS Mode Wireless Band: Select either 2.4GHz or 5GHz from the drop-down menu. Mode: WDS is selected from the drop-down menu. Network Name (SSID): Service Set Identifier (SSID) is the name designated for a specific wireless local area network (WLAN). The SSID’s factory default setting is dlink.
D-Link DAP-2695 User Manual Site Survey: Click on the Scan button to search for available wireless networks, then click on the available network that you want to connect with. Authentication: Use the drop-down menu to choose Open System, Shared Key, or WPA-Personal.
Wireless Client mode. Channel: The channel used will be displayed, and matches the AP that the DAP-2695 is connected to when set to Wireless Client mode. Channel Width: Use the drop-down menu to choose 20 MHz or Auto 20/40 MHz.
D-Link DAP-2695 User Manual Wireless Security Wireless security is a key concern for any wireless network installed. Unlike any other networking method wireless networks will broadcast it’s presence for anyone to connect to it. Today, wireless security has advanced to a level where it is virtually impenetrable.
D-Link DAP-2695 User Manual Wi-Fi Protected Access (WPA / WPA2) WPA was created by the Wi-Fi Alliance to address the limitations and weaknesses found in WEP. This protocol is mainly based on the 802.11i standard. There are also two variations found in WPA called WPA-Personal (PSK) and WPA-Enterprise (EAP).
D-Link DAP-2695 User Manual WPA Mode: When WPA-Enterprise is selected, you must also select a WPA mode from the drop-down menu: AUTO (WPA or WPA2), WPA2 Only, or WPA Only. WPA and WPA2 use different algorithms. AUTO (WPA or WPA2) allows you to use both WPA and WPA2.
D-Link DAP-2695 User Manual LAN is short for Local Area Network. This is considered your internal network. These are the IP settings of the LAN interface for the DAP-2695. These settings may be referred to as private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet.
D-Link DAP-2695 User Manual Advanced Settings In the Advanced Settings Section the user can configure advanced settings concerning Performance, Multiple SSID, VLAN, Security, Quality of Service, AP Array, Web Redirection, DHCP Server, Filters and Scheduling. The following pages will explain settings found in the Advanced Settings section in more detail.
D-Link DAP-2695 User Manual Performance On the Performance Settings page the users can configure more advanced settings concerning the wireless signal and hosting. Wireless Band: Select either 2.4GHz or 5GHz. Wireless: Use the drop-down menu to turn the wireless function On or Off.
D-Link DAP-2695 User Manual Transmit Power: This setting determines the power level of the wireless transmission. Transmitting power can be adjusted to eliminate overlapping of wireless area coverage between two access points where interference is a major concern. For example, if wireless coverage is intended for half of the area, then select 50% as the option.
APs. If this function is enabled and when the number of users ex- ceeds this value, or the network utilization of this AP exceeds the percentage that has been specified, the DAP-2695 will...
Network Utilization: Set the maximum utilization of this access point for service. The DAP-2695 will not allow any new clients to associate with the AP if the utilization exceeds the value the user specifies. Select a utilization percentage between 100%, 80%, 60%, 40%, 20%, or 0%.
D-Link DAP-2695 User Manual Multi-SSID The device supports up to four multiple Service Set Identifiers. You can set the Primary SSID in the Basic > Wireless section. The SSID’s factory default setting is dlink. The SSID can be easily changed to connect to an existing wireless network or to establish a new wireless network.
D-Link DAP-2695 User Manual Encryption: When you select Open System, toggle between Enable and Disable. If Enable is selected, the Key Type, Key Size, Key Index (1~4), Key, and Confirm Keys must also be configured. Key Type: Select HEX or ASCII.
The DAP-2695 supports VLANs. VLANs can be created with a Name and VID. Mgmt (TCP stack), LAN, Primary/Multiple SSID, and WDS connection can be assigned to VLANs as they are physical ports. Any packet which enters the DAP-2695 without a VLAN tag will have a VLAN tag inserted with a PVID.
D-Link DAP-2695 User Manual Port List The Port List tab displays the current ports. If you want to configure the guest and internal networks on a Virtual LAN (VLAN), the switch and DHCP server you are using must also support VLANs. As a prerequisite step, configure a port on the switch for handling VLAN tagged packets as described in the IEEE 802.1Q standard.
D-Link DAP-2695 User Manual Add/Edit VLAN The Add/Edit VLAN tab is used to configure VLANs. Once you have made the desired changes, click the Save button to let your changes take effect. VLAN Status: Use the radio button to toggle to Enable.
D-Link DAP-2695 User Manual PVID Settings The PVID Setting tab is used to enable/disable the Port VLAN Identifier Auto Assign Status as well as to configure various types of PVID settings. Click the Save button to let your changes take effect.
D-Link DAP-2695 User Manual Intrusion The Wireless Intrusion Protection window is used to set APs as All, Valid, Neighborhood, Rogue, and New. Click the Save button to let your changes take effect. Wireless Band: Select 2.4GHz or 5GHz. AP List: The choices include All, Valid, Neighbor, Rogue, and New.
D-Link DAP-2695 User Manual Schedule The Wireless Schedule Settings window is used to add and modify scheduling rules on the device. Click the Save button to let your changes take effect. Wireless Schedule: Use the drop-down menu to enable the device’s scheduling feature.
This table displays the current AP array status for the following parameters: Array Name, Master IP, MAC, Master, Backup Master, Slave, and Total. Current Array Members: This table displays all the current array members. The DAP-2695 AP array feature supports up to eight AP array members.
D-Link DAP-2695 User Manual Wireless Basic Settings Network Name (SSID): Select this option to use a Network Name (SSID). SSID Visibility: Select this option to enable SSID Visibility. Auto Channel Selection: Select this option to use Auto Channel Selection. Channel Width: Select this option to specify the Channel Width.
D-Link DAP-2695 User Manual Multiple SSID & VLAN SSID: Select this option to use an SSID. SSID Visibility: Select this option to make the SSID Visible. Security: Select this option to use Wireless Security. WMM: Select this option to use WMM.
D-Link DAP-2695 User Manual Web Redirection This page allows the user to setup a Web Redirection Page for Hotspot roaming users prior and after to authentication. Enable Web Redirection: This check box allows the user to enable the Web Redirection function.
Internal RADIUS Server The DAP-2695 features a built-in RADIUS server. Once you have finished adding a RADIUS account, click the Save button to let your changes take effect. The newly-created account will appear in this RADIUS Account List. The radio buttons allow the user to enable or disable the RADIUS account.
D-Link DAP-2695 User Manual ARP Spoofing Prevention The ARP Spoofing Prevention feature allows users to add IP/MAC address mapping to prevent arp spoofing attack. ARP Spoofing Prevention: This check box allows you to enable the arp spoofing prevention function. Gateway IP Address: Enter a gateway IP address.
D-Link DAP-2695 User Manual Fair Air Time The Fair Air Time window allows the user to manage the bandwidth of the device and arrange the bandwidth for various wireless clients. When the fair air time rule is finished, click the Add button. To discard the Add Fair Air Time Rule settings, click the Clear button. Click the Save button to let your changes take effect.
The DHCP address pool defines the range of the IP address that can be assigned to stations in the network. A Dynamic Pool allows wireless stations to receive an available IP with lease time control. If needed or required in the network, the DAP-2695 is capable of acting as a DHCP server.
IP addresses automatically without the need to manually assign IP addresses. Select Enable to allow the DAP-2695 to function as a DHCP server. Assigned IP: Use the Static Pool Settings to assign the same IP address to a device every time you start up.
D-Link DAP-2695 User Manual Current IP Mapping List This window displays information about the current assigned DHCP dynamic and static IP address pools. This information is available when you enable DHCP server on the AP and assign dynamic and static IP address pools.
D-Link DAP-2695 User Manual Filters Wireless MAC ACL This page allows the user to configure Wireless MAC ACL settings for access control. Wireless Band: Displays the current wireless band rate. Access Control List: Select Disable to disable the filters function.
D-Link DAP-2695 User Manual WLAN Partition This page allows the user to configure a WLAN Partition. Wireless Band: Displays the current wireless band. Select Enable or Disable. If the Ethernet Link Integrity: connection between the LAN and the AP is...
D-Link DAP-2695 User Manual Traffic Control Uplink/Downlink Setting The uplink/downlink setting allows users to customize the downlink and uplink interfaces including specifying downlink/uplink bandwidth rates in Mbits per second. These values are also used in the QoS and Traffic Manager windows. Once the desired uplink and downlink settings are finished, click the Save button to let your changes take effect.
D-Link DAP-2695 User Manual Quality of Service (QoS) enhances the experience of using a network by prioritizing the traffic of different applications. The DAP-2695 supports four priority levels. Once the desired QoS settings are finished, click the Save button to let your changes take effect.
D-Link DAP-2695 User Manual Traffic Manager The traffic manager feature allows users to create traffic management rules that specify how to deal with listed client traffic and specify downlink/ uplink speed for new traffic manager rules. Click the Save button to let your changes take effect.
D-Link DAP-2695 User Manual Status In the Status Section the user can monitor and view configuration settings of the access point. Here the user can also view statistics about client information, WDS information and more. The following pages will explain settings found in the Status section in more detail.
This page displays the current information like firmware version, Ethernet and wireless parameters, as well as the information regarding CPU and memory utilization. Device Information: This read-only window displays the configuration settings of the DAP-2695, including the firmware version and the device’s MAC address.
D-Link DAP-2695 User Manual Client Information This page displays the associated clients SSID, MAC, band, authentication method, signal strength, and power saving mode for the DAP-2695 network. Client Information: This window displays the wireless client information for clients currently connected to the DAP-2695.
D-Link DAP-2695 User Manual WDS Information Page This page displays the access points SSID, MAC, band, authentication method, signal strength, and status for the DAP-2695’s Wireless Distribution System network. WDS Information: This window displays the Wireless Distribution System information for clients currently connected to the DAP-2695.
D-Link DAP-2695 User Manual Channel Analyze Wireless Band: Select either 2.4Ghz or 5GHz. Detect: Click the Detect button to scan. AP List: This will list the transmitting channels and quality.
D-Link DAP-2695 User Manual Stats Page Ethernet Traffic Statistics Displays wired interface network traffic information. Ethernet Traffic Statistics: This page displays transmitted and received count statistics for packets and bytes.
D-Link DAP-2695 User Manual WLAN Traffic Statistics Displays throughput, transmitted frame, received frame, and WEP frame error information for the AP network. WLAN Traffic Statistics: This page displays wireless network statistics for data throughput, transmitted and received frames, and frame errors.
D-Link DAP-2695 User Manual View Log The AP’s embedded memory holds logs here. The log information includes but is not limited to the following items: cold start AP, upgrading firmware, client associate and disassociate with AP, and web login. The web page holds up to 500 logs.
Log Server/IP Address: Enter the IP address of the server you would like to send the DAP-2695 log to. Log Type: Check the box for the type of activity you want to log. There are three types: System Activity, Wireless Activity, and Notice.
D-Link DAP-2695 User Manual Maintenance Section In the Status Section the user can monitor and view configuration settings of the access point. Here the user can also view statistics about client information, WDS information and more. The following pages will explain settings found in the maintenance section in more detail.
D-Link DAP-2695 User Manual Administration Limit Administrator Check one or more of the five main categories to display the various hidden administrator parameters and settings displayed on the next five pages. Each of the five main categories display various hidden administrator parameters and settings.
D-Link DAP-2695 User Manual System Name Settings Each of the five main categories display various hidden administrator parameters and settings. System Name: The name of the device. The default name is D-Link DAP-2695. Location: The physical location of the device, e.g.
D-Link DAP-2695 User Manual SNMP Settings Each of the five main categories display various hidden administrator parameters and settings. Status: Check the box to enable the SNMP functions. This is enabled by default. Public Community String: Enter the public SNMP community string.
This is a useful feature that prevents future bugs and allows for new features to be added to this product. Please go to your local D-Link website to see if there is a newer version firmware available. Firmware and SSL You can upload files to the access point.
Click “Download” to save the current configuration file to your local disk. Note that if you save one configuration file with the administrator’s password now, after resetting your DAP-2695 and then updating to this saved configuration file, the password will be gone.
D-Link DAP-2695 User Manual Time and Date Settings Enter the NTP server IP, choose the time zone, and enable or disable daylight saving time. Current Time: Displays the current time and date settings. Enable NTP Server: Check to enable the AP to get system time from an NTP server from the Internet.
D-Link DAP-2695 User Manual Configuration and System These options are the remaining option to choose from in the top menu. Configuration allows the user to save and activate or discard the configurations done. System allows the user to restart the unit, perform a factory reset or clear the language pack settings. Logout allows the user to safely log out from the access point’s web configuration.
On this page the user can restart the unit, perform a factory reset of the access point or clear the added language pack. Restart the Device: Click Restart to restart the DAP-2695. Restore to Factory Default Click Restore to restore the DAP-2695 Settings: back to factory default settings.
D-Link DAP-2695 User Manual Help The help page is useful to view a brief description of a function available on the access point in case the manual is not present. Help: Scroll down the Help page for topics and explanations.
Wireless Basics D-Link wireless products are based on industry standards to provide high-speed wireless connectivity that is easy to use within your home, business or public access wireless networks. D-Link wireless products provides you with access to the data you want, whenever and wherever you want it.
Wireless Installation Considerations The D-Link Access Point lets you access your network using a wireless connection from virtually anywhere within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range.
Close your web browser (if open) and open it. • Access the web management. Open your web browser and enter the IP address of your D-Link access point in the address bar. This should open the login page for your the web management.
D-Link DAP-2695 User Manual How to check your IP address? After you install your network adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below.
D-Link DAP-2695 User Manual How to statically assign an IP address? If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below: Step 1: Windows® 2000: Click on Start > Settings > Control Panel > Network Connections Windows XP: Click on Start >...
D-Link DAP-2695 User Manual Technical Specifications Standards LEDs • IEEE 802.11ac (draft) • Power • IEEE 802.11n • LAN1 (PoE) • IEEE 802.11g • LAN2 • IEEE 802.11a • 2.4 GHz • IEEE 802.3 • 5 GHz • IEEE 802.3u •...