Locking Controls And Settings; System Reset - Shure ULX-D Manual

Locking Controls and Settings

Use the feature to prevent accidental or un-
LOCK
authorized changes to the hardware. Attempting to
access a locked feature will display the following
message:
Receiver
Menu path: >
UTILITIES LOCK
: All menu paths are inaccessible. To unlock, press the
MENU
turn the control wheel to select
: Gain adjustment is locked
GAIN
: Power switch is disabled
POWER
: Cannot perform a Scan and Sync
SCN/SYC
Transmitter
Menu path: >
UTILITY LOCK
: All menu paths are inaccessible. To unlock, press the
MENU
four (4) times to pass through the following screens:
MENU UNLOCK
: Power switch is disabled
POWER
Quick-Lock Option: To turn on the transmitter with its power and menu
navigation buttons locked, press and hold the ▲ button during power-on
until the locked message is displayed.
To unlock, turn the power switch to the off position, then press and hold
the ▲ button while turning the power switch to the on position.
Transmitter Presets
Use the menu to store settings on the receiver to transfer to
TX SYNC SETUP
the transmitter during a sync. Each parameter has the default value
which leaves that setting unaffected by a sync.
Feature Setting
0 dB, -12 dB
BP PAD
All, Power, Menu, None
LOCK
High, Mid, Low
RF POWER
, 0 dB to +21 dB (in 3 dB increments)
BP OFFSET HH OFFSET
NiMH, Lithium, Alkaline
BATT
On, Off
Cust. Group
Note: When Cust. Groups is set to on, it may take up to 30 seconds to com-
plete an IR sync.
Encryption
ULXD features Advanced Encryption Standard (AES-256) encryption,
conforming to the US Government National Institute of Standards and
Technology (NIST) publication FIPS-197.
1. Enable encryption on the receiver:
The encryption symbol illuminates green and the LCD displays
.
SYNC NOW FOR ENCYPTION
2. Sync the transmitter to the receiver. The encryption symbol displays on
the transmitter.
Note: Any change to the encryption status on the receiver requires a sync
to transfer the setting to the transmitter. The Encryption Mismatch warning
will display on the receiver LCD panel if they are not on the same setting.
10
EXIT
and press to save.
UNLOCKED ENTER
ENTER
>
UTILITY
>
UTILITIES ENCRYPTION

System Reset

Use this feature to overwrite current settings with saved or factory default
settings.
Save a System Preset
To save the current receiver setup as a new preset:
SYSTEM RESET
Restore Settings
button,
To restore saved or factory default settings:
1. Go to
UTILITES
2. Scroll to the preset or default settings option and press
lowing warning will display:
3. Press the flashing
button
Advanced RF
>
LOCK
RF Mute
Use this to turn on a transmitter without interfer-
ing with the RF spectrum.
Press and hold the
until
RF MUTED
the transmitter.
Custom Groups
Use this feature to create up to six groups of manually selected frequencies
that can be exported to networked receivers to simplify system setup.
To create a custom group:
,
KEEP
Note: Use Wireless Workbench or Wireless Frequency Finder to select the
best compatible frequencies. See www.shure.com for more information.
To export a custom group:
1. Go to
UTILITES
lowing screen will display.
2. Press the flashing
ers on the network.
Antenna Bias
To turn off:
UTILITES
.
> >
SAVE CREATE NEW PRESET
> >
SYSTEM RESET RESTORE
button to overwrite the current settings.
ENTER
button during power-on
exit
is displayed. To un-mute, restart
>
UTILITES ADVANCED RF
> >
ADVANCED RF CUSTOM GROUPS
button to export all custom groups to all receiv-
ENTER
> >
ADVANCED RF ANTENNA BIAS
>
UTILITES
.
.
. The fol-
ENTER
>
CUSTOM GROUPS
> . The fol-
EXPORT
.