Starting And Shut Off - Ariens 920014 COMPACT 24 LE Owner's/Operator's Manual

8. Check Skid Shoes
Check and adjust skid shoes (Skid Shoes on
page 25). Allow 1/8 in. (3 mm) between
scraper blade and hard, smooth surface(s).
Allow 7/8 in. (22 mm) between scraper blade
and uneven or gravel surfaces.
9. Check Engine Fuel &
Crankcase Oil
WARNING: AVOID INJURY. Read
and understand the entire Safety
section before proceeding.
Check and add fuel if required. Check that
the engine crankcase oil is full using dipstick.
Refer to Engine Manual for detailed
instructions.
TO STOP IN AN EMERGENCY
Immediately release both control levers to
stop unit in an emergency. Stop engine,
remove key and wait for all rotating parts to
stop before leaving operator's position.

STARTING AND SHUT OFF

WARNING: FAILURE TO FOLLOW
INSTRUCTIONS could result in
personal injury and/or damage to
unit. DO NOT attempt to start your
unit at this time. Read entire
Owner/Operator Manual and the
Engine Manual first.
IMPORTANT: Allow unit and engine to adjust
to the outdoor temperature before clearing
snow. Before shut-off, run the attachment a
few minutes to prevent impeller freeze-up.
NOTE: Try out each control without the
engine running to see how it works and what
it does.
Manual Start
1. Turn discharge chute straight ahead.
2. Make sure that the traction clutch and
attachment drive clutch levers are fully
disengaged.
3. Push Primer Bulb 2 or 3 times for cold
engine.
NOTE: When temperature is below -15° F
(-26° C) additional priming may be needed.
4. If engine is cold, apply choke. See
Engine Manual for detailed instructions.
NOTE: A warm engine requires less choking
than a cold engine.
5. 920014 – Set throttle to proper starting
position.
920013 – Toggle ignition switch to
"Run".
6. 920014 – Insert key into ignition and
rotate to run position.
920013 – Insert key into ignition switch
and push into RUN position. DO NOT
twist key after it is inserted.
7. Grasp starter handle and pull rope out
slowly until it pulls harder. Let rope
rewind slowly.
8. Pull rope with a rapid continuous full arm
stroke. Let rope rewind slowly.
IMPORTANT: DO NOT let Starter Handle
snap against Starter.
9. Repeat steps 7 and 8 until engine starts.
(If engine does not start, refer to
TROUBLESHOOTING on page 33.)
10. Adjust choke as needed.
11. 920014 – Set throttle to Part Throttle or
Slow position for adaptation to outside
temperature or travel. Set throttle to Fast
position for normal operation.
Electric Start (120V)
1. Connect extension cord to starter.
IMPORTANT: Prevent damage to unit. Know
voltage of your starter and only use matching
outlets.
2. Plug extension cord into 120V 3-wire,
grounded outlet.
IMPORTANT: Use only Ariens extension cord
(P/N 02483100) or an equivalent cord that is
rated for a minimum of 13 amps, grounded,
UL listed, CSA certified and labeled as
suitable for outdoor use.
3. Turn discharge chute straight ahead.
4. Make sure that the traction clutch and
attachment drive clutch levers are fully
disengaged.
5. Push Primer Bulb 2 or 3 times for cold
engine.
NOTE: When temperature is below -15° F
(-26° C) additional priming may be needed.
6. 920014 – Set throttle to proper starting
position.
920013 – Toggle ignition switch to
"Run".
7. 920014 – Insert key into ignition and
rotate to run position.
920013 – Insert key into ignition switch
and push into RUN position. DO NOT
twist key after it is inserted.
8. If engine is cold, apply choke. A warm
engine requires less choking than a cold
engine. See Engine Manual for detailed
instructions.
9. 920014 – Set throttle to proper starting
position
10. Press starter button on engine until
engine starts.
GB - 20