Table of Contents
Advertisement
Connections
Switching the output signal (interlaced / progressive)
using the remote control
You can temporarily switch the output signal for better picture quality.
Press PROGRESSIVE button repeatedly on the remote control to
select Video Output to P-Scan mode during stop.
If your TV does not support the progressive scan format, the picture
will appear scrambled or blank. To return to normal picture, press
PROGRESSIVE button repeatedly to turn off progressive mode.
Notes
• Refer to the owner's manual of the connected equipment as well.
• When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the wall outlet
before making any connections.
• If you place the DVD player near a tuner or radio, the radio broadcast sound might be distorted. In this case, place the DVD player away from
the tuner and radio.
• The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver's volume to a moderate listening level.
Otherwise, high volume sound may damage your hearing as well as the speakers.
• Turn off the amplifier before you connect or disconnect the DVD player's power cord. If you leave the amplifier power on, the speakers may
be damaged.
• Analog audio out will not have sound if DTS playback is selected.
®
®
• ColorStream
and ColorStream Pro
are registered trademarks of Toshiba America Cousumer Products L.L.C.
Connecting to a display (Using a HDMI
Available output signals are below:
•
Auto
•
480p (progressive)
•
720p (progressive)
•
1080i (interlaced)
•
1080p (progressive)
•
1080p/24F (progressive)
Switching the video quality (HDMI mode) using HDMI
button on the remote control.
Press HDMI button on the remote control to receive a suitable
video quality in STOP mode. The video quality is required to match
your TV having HDMI feature and suitable quality. Please also check
your TV owner's manual. Press this button to change the output
signals as below. See the HDMI indicator and select the appropriate
output signal.
HDMI indicator
Video output signal
illuminates " 1080p, 24F"
1080p/24F (progressive)
Press
illuminates " 1080p"
1080p (progressive)
Press
illuminates "1080i"
1080i (interlaced)
Press
illuminates "720p"
720p (progressive)
Press
illuminates "480p"
480p (progressive)
Press
illuminates "480p, 720p,
1080i, 1080p"
Press
480p, 720p, 1080i,1080p and 1080p/24F are signals created
with this DVD Player from original 480i signal. The resolution
of the picture may not be increased even if they are selected.
12
• Make the following setting.
On-screen display
"Digital Output"
"Video Output"
* Only for TV equipped with component video
input jacks which support the progressive scan.
TM
cable)
T o HDMI
Output
HDMI Cable
(not supplied)
HDMI-compatible display
• Make the following setting.
On-screen display
"Digital Output"
"Video Output"
About HDMI
HDMI (High Definition Multimedia Interface) supports both video
and audio on a single digital connection for use with DVD players,
DTV, set-top boxes, and other AV devices. HDMI was developed
to provide the technologies of High Bandwidth Digital Content
Protection (HDCP) as well as Digital Visual Interface (DVI) in
one specification. HDCP is used to protect digital content
transmitted and received by DVI-compliant or HDMI-compliant
displays.
HDMI has the capability to support standard, enhanced, or high-
definition video plus standard to multi-channel surround-sound
audio. HDMI features included uncompressed digital video, a
bandwidth of up to 2.2 gigabytes per second (with HDTV) signals, one
Auto
connector (instead of several cables and connectors), and
communication between the AV source and AV devices such as
DTVs.
HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI licensing LLC.
Page
Select:
"PCM" or
32
"Bitstream"
Component
*P-Scan
31
(Progressive)
Select:
Page
"PCM"
32
HDMI
31
Advertisement
Table of Contents
