Summary of Contents for ALCON ALCON-7
-
Page 1: Operation Guide
MIDDLE RANGE RF TELECOM SYSTEM STATlON TO STATION STATION TO MOBILE OPERATION GUIDE... -
Page 2: Table Of Contents
: ALCON-7 Pointto point / point to Mobile cordless telephone system. This ALCON product will give you years of performance if you read and follow carefully the instructions contained in this manual. -
Page 3: Standard Package
RF STABlLITY & DURABILlTY SCRAMBLER FUNCTlON 4O CHANNELS FREQUENCY AUTO SCAN TWO-WAY PAGING & lNTERCOM MODULAR DESIGN STANDARD PACKAGE ALCON-7 BASE UNIT AND REMOTE / MOBILE Standard Accessories for ALCON-7 S.S. Base Unit 5DFB 20m Cable Remote / Mobile Unit AT-526 Normal Telephone Switching Adaptor User’s Manual... - Page 4 Standard Accessories for ALCON-7 S.M. Base Unit Remote / Mobile Unit Switching Adaptor 5DFB 20m Cable A-7 Antenna AT-80 Telephone 1/2 λ Car Antenna Magnetic Car Antenna Mount DC Cord User’s Manual Standard Accessories for ALCON-7 S.M. Remote / Mobile Unit...
-
Page 5: Function Keys
FUNCTION KEYS : Base Unit REDIAL Redial Key FLASH Flash Key HOLD Hold Key CONF Three-Way Conference Call Speakerphone Key Remote/Mobile Unit Scramble Scramble Key Intercom Intercom Key Scramble Key Intercom Key Scramble indicator Intercom indicator In Use indicator Power indicator Flash Key Redial Key Three-Way... -
Page 6: Answering A Call
ANSWERING A CALL ANSWERING WITH THE ALCON-7 Remote Unit Make sure the Remote POWER switch is ON. 1. When a call comes in, the Normal Telephone will ring. The TEL indicator will flash. 2. Pick-up the handset of the Normal Telephone and begin your conversation. -
Page 7: Placing A Call
RINGER VOLUME CONTROL Set the RINGER switch on the middle right side of the base unit to ON (up) or OFF (down). RINGER ON/OFF SWITCH VOLUME CONTROL SCRAMBLE FUNCTION To prevent somebody from eavesdropping on your conversation, use the Scramble function. . 1. -
Page 8: Base Unit
BASE UNIT There are two methods to place a call using the base unit. A. Picking up the Receiver from the Base Unit 1. Listen for a dial tone by lifting the Receiver from the base unit. The TEL indicator and dialing buttons (green light) will illuminate. - Page 9 INTERCOM FUNCTION {BETWEEN REMOTE/ MOBILE UNIT AND BASE UNIT} A : Remote / Mobile CALLING BASE UNIT Remote / Mobile 1. Press INTERCOM. The base will emit two short “beeps”. The Remote/Mobile unit INT indicator will begin to flash. 2. Lift the telephone handset and wait for somebody to activate the Base Unit.
-
Page 10: Transferring Calls
Remote/ Mobile unit 1. The Remote/ Mobile unit will ring. The INT indicator will flash. This means that the Base unit is calling the Remote/ Mobile unit. 2. Once you lift the telephone handset, you can begin you conversation . The INT indicator will continuously illuminate. -
Page 11: 3-Way Conference Calls
3-WAY CONFERENCE CALLS BETWEEN THE BASE UNIT AND REMOTE/ MOBILE UNIT AND OUTSIDE CALL OR BASE UNIT CALLING THE REMOTE UNIT DURING AN OUTSIDE CALL Base Unit 1.Press Hold button. The TEL indicator will flash. 2. Press CALL. The CALL indicator will illuminate. 3. -
Page 12: Redial Function
REDIAL FUNCTION You can redial the last telephone number dialed automatically {after getting a busy signal, for instance} Base Unit 1. Pick up the receiver of the base unit or press to get a dial tone. The TEL key will illuminate. If you use, it will illuminate as well. -
Page 13: Flash Function
FLASH FUNCTION The FLASH button can be used to get a new dial tone without pressing You can also use the flash function to obtain special services, such as Call Waiting from your local PTT or PBX. If you subscribe to “Call Waiting” : 1. -
Page 14: Antenna Installation
NOTE : Once you press the digit button, you must complete the following procedures within 5 seconds to saccessfally complete the procedure. Remote/ Mobile Unit 2. Press INTERCOM (without letting go) and switch POWER to ON. The POWER, TEL, IN USE, INT, and SCRAM indicator will illuminate meaning that your procedure has been successfully completed. - Page 16 Bringing People Together Printed in Taiwan...