Table of Contents
Advertisement
CONNECTION
1.
Connecting the soundbar to your TV: The sound bar part of your Energy Power Bar
Elite system is what needs to be connected to your TV, Cable Box or Satellite Re-
ceiver. If you have other devices connected to your TV, such as a DVD /BiuRay player,
gaming system,
etc.,
connect the soundbar to the TV so that you can listen to all
those and your TV through the sound bar. If there are no other devices connected to
your TV other than a cable or satellite box and you receive all of your television pro-
grams from that box, you can connect the sound bar to either that box or your
are three different ways to connect the sound bar to your
A. Digital Optical Cable
Since most High Definition TV's, Satellite and Cable boxes have an DIGITAL OPTICAL AU-
DIO OUTPUT, we have included that cable. Simply connect one end of that included cable
into the corresponding output of your TV, Satellite or Cable box and connect the other end
of the cable into the DIGITAL OPTICAL INPUT on the back panel of the sound
TV Connection Panel
§ )
HDMI
Z
§ )
HDMI3
B. RCA Cable
If you do not have an optical digital output, you can use analog left and right audio
outputs on your device and connect them to the analog left and right inputs on the
sound bar with the supplied cable.
TV Connection Panel
C. 3.5mm Output (Headphone Jack)
A third choice would be to connect from a headphone output on your device to the
analog left and right inputs on the soundbar (cable NOT
Once you have made any of the above audio cable
supplied soundbar power supply into the "DC Input" on the back of the sound bar
and turn the Main Power Switch on the back of the soundbar
TV,
Satellite or Cable
bar.
Soundbar Connection Panel
O CIH
POWER
Of
f [gON
24V
"'
H
A
55W
Digital Optical Cable i
----~S.~pplie~
j
__
___
3.5mm to Male RCA
Cable
(Not Supplied)
Male RCA to Male
RCA Cable
(S
upplied!
DC
IN
POW£R
24V:::
2.5A
ssw
II[
orr
oil
ON
Sound bar Connection Panel
supplied).
Soundbar
Connection Panel
Supply
Power
and ACCord
connections,
connect the
on.
2. Connecting the subwoofer to the soundbar: Once you have placed the sub-
woofer in the room, take the supplied subwoofer power cord, plug one end into
the subwoofer where it is labeled "AC In" and plug the other end into an active
electrical socket. Turn the Main Power Switch on the back of the subwoofer on. On
the sound bar, make sure the left status light is either solid green or orange (press
SOURCE button once if light is steady red). The red light will turn on until it finds the
wireless signal coming from the soundbar. Once it finds that signal (approximately
seconds),
the solid red light will change to solid
TV.
There
connected to the
soundbar.
box.
Subwoofer Rear Connection Panel
0
Ei''"'Ete>~~!i.~.~
0
0
OJ
0
PROGRAMMING YOUR TV REMOTE TO OPERATE THE SOUNDBAR
The Energy Power Bar Elite has been pre-programmed to work with many Sam sung TV's,
so if you have one check to see if your Samsung TV remote automatically changes the
sound bar volume and puts the sound
you do not need to manually program your TV
your Energy Power Bar Elite system you find that your TV remote automatically controls
the volume up and down through the sound bar (indicating you have a "variable" audio
output on your TV) you will not need to program VOLUME UP(+) or VOLUME DOWN(-)
when programming your TV
box remote control if your sound bar is connected to that) according to the quick setup
guide
included with
the
Soundbar Front
Control Panel
1.
IF THE SOUNDBAR IS IN STANDBY MODE (solid red left status light), push any but-
ton on the soundbar until the left status light is solid orange OR
left status light
showing
both
the
SOURCE and MUTE button on the front o
(approximately
3
2.
Press and hold down MUTE button on sound bar until the left
solid orange.
3. Hold your remote within one foot of the front of the sound bar. Press the MUTE but-
ton on your remote control four
cator light will flash with each
This
indicates
that the soundbar has
into the MUTE key (therefore, when you
the sound bar will go into Standby and not output sound.
your remote will take the Power Bar Elite out of Standby and the sound bar will out-
put sound).Repeat steps
UP and VOLUME DOWN
with
SOURCE,
VOLUME
blue,
indicating the subwoofer is now
0
Status Light
AC Power Cord
bar
into "STANDBY" when MUTE is pressed. If
remote.
Also, if once you have connected
remote.
Program your TV remote control (or satellite or cable
soundbar.
STATUS LIGHTS
SOURCE
VOLUME UP
VOLUME DOWN
either solid orange or solid
green,
f
the sound bar at the same time
seconds) until the left status light flashes
times.
The first three presses, the left status
press,
and then will turn solid on the fourth
"learned"
the
MUTE
press
mute on your remote to mute sound
ONE,
TWO and THREE to program the
buttons
on your remote to the sound
UP or VOLUME DOWN on
Steps T
15
so,
MUTE
green.
With
the
press and hold down
orange.
status
light stays
indi-
press.
function on your remote
Pressing
mute again on
SOURCE,
VOLUME
bar.
(Replace MUTE
wo and Three).
Hide quick links:
Advertisement
Table of Contents
