Advertisement
Table of Contents
- 1 Table of Contents
- 2 Features and Benefits
- 3 Speaker Placement
- 4 Selection of Proper Wire
- 5 Amplifier Requirements
- 6 Amplifier to Loudspeaker Connection
- 7 Conventional Hook-Up
- 8 Bi-Wire Hook-Up
- 9 Combination Bi-Amp/Bi-Wire Hook-Up
- 10 Care of Finish
- 11 Distortion Causes Speaker Damage
- 12 Specifications
- 13 Warranty
- 14 Warning
- Download this manual
Advertisement
Table of Contents
Related Manuals for Energy Audissey Series
Summary of Contents for Energy Audissey Series
- Page 1 L O U D S P E A K E R S M U S I C A L o w n e r s PRINTED IN CANADA 7AI//E-EA T R U T H A u d i s s e y S e r i e s m a n u a l ®...
-
Page 2: Table Of Contents
Distortion Causes Speaker Damage ........8... -
Page 3: Features And Benefits
A u d i s s e y S e r i e s o w n e r s m a n u a l WELCOME TO THE WORLD OF ENERGY “AUDISSEY” LOUDSPEAKERS. We are sure you will enjoy this superb product.The following advice is offered to facilitate proper installation of your Energy speakers in your home. - Page 4 6. The distance from the left and right speaker to the side walls should be equal. For best results, placement distance from the rear wall should not be the same as from the side walls.
-
Page 5: Speaker Placement
8. The loudspeakers should be placed 2 to 3 meters (6’ to 10’) apart.The distance from loudspeakers to listener should be about 1 to 1.5 times the distance separating the speakers. (see figure 1). SPEAKER PLACEMENT o w n e r s m a n u a l (FIGURE 1) -
Page 6: Selection Of Proper Wire
In most installations, ordinary lamp cord (16-18 gauge) has enough resistance to degrade the signal between amplifier and speakers, particularly in lengths over 3 meters (10’). If possible the speaker cables should be the same length for both channels and the shorter they are, the better the sonic performance will be. - Page 7 A u d i s s e y S e r i e s o w n e r s m a n u a l...
- Page 8 o w n e r s m a n u a l A u d i s s e y S e r i e s...
-
Page 9: Combination Bi-Amp/Bi-Wire Hook-Up
When an amplifier is “overdriven” it produces distorted output power several times greater than its rated power. All amplifiers produce high levels of distortion when they are driven beyond their rated power output and this distortion can damage any speaker. Overdriven amplifier distortion is called “Clipping”. -
Page 10: Specifications
o w n e r s m a n u a l SPECIFICATIONS SYSTEM TYPE: TWEETERS: WOOFERS: SUBWOOFERS: FREQUENCY RESPONSE: CROSSOVER POINTS: SENSITIVITY: IMPEDANCE: REC.AMP POWER: clipping less than 10% DIMENSIONS: (in) (cm) WEIGHT (each): FINISH: GRILLE COLOUR: DESCRIPTIONS AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE. A2+2 A3+2 Asymmetrical... -
Page 11: Warranty
A u d i s s e y S e r i e s o w n e r s m a n u a l LIMITED WARRANTY POLICY Warranty in the United States and Canada Mirage warrants this product to the retail purchaser against any failure resulting from original manufacturing defects in workmanship or materials.The warranty is in effect for a period of five (5) years from date of purchase from an authorized Mirage dealer and is valid only if the original dated bill of sale is presented when service is required. -
Page 12: Warning
CLIPPING CAN BE IDENTIFIED BY A FUZZY OR DISTORTED SOUND. IF THIS IS HEARD, LOWER THE VOLUME IMMEDIATELY TO AVOID DAMAGE TO YOUR SYSTEM.