Denon AVR-1709 Owner's Manual page 39

1m
Dynamic EQ
Audyssey Dynamic EO solves the problem of deteriorating sound
quality as volume is decreased by taking into account human perception
and room acoustics. Audyssey Dynamic EO works in tandem with
Audyssey MultEO to provide well-balanced sound for every listener
at any volume level.
-N,n.
• "Dynamic EO" can only be set when auto setup has been
performed.
• "Dynamic EO" cannot be set in the following situations.
• If "Auto Setup" fails to be completed.
• After running Auto Setup, when the number of used speakers has
increased from the number of measured speakers.
• When" MultEO" is set to "OFF': "Dynamic EO" is automatically set
to "OFF".
• "Night Mode" and "Tone Control" cannot be used jointly.
[Selectable items]
~:
Use Dynamic EO function.
OFF
Do not use Dynamic EO function.
Operating from the main unit or main remote
control unit
<DYN VOl> [DYNAMIC VOLUME].
Press or
Dynamic EO / Volume: ON - - Dynamic EO : ON / Volume: OFF
C
- Dynamic EO / Volume: OFF ....
Before running Auto Setup and after running Auto Setup, if the number
<DYN VOl>
of speakers has increased or you pressed
VOLUME],
"Run Audyssey" is displayed. In this case, either perform
Auto Setup again, or return to the setting after running Auto Setup with
"System Setup" - "Speaker Setup" - "Restore".
OOperating conditions for each function
• Dynamic EQ: When "MultEO" is set to "ON"
• Dynamic Volume: When "Dynamic EO" is set to "ON"
• DV setting: When "Dynamic Volume" is set to "ON"
• DynamlcEQ
PI
Dynamic Volume
<;
( PI
DV Setting
fi
Dynamic Volume
Audyssey Dynamic Volume solves the problem of large variations in
volume level between television programs, commercials, and between
the soft and loud passages of movies.
Audyssey Dynamic EO is integrated into Dynamic Volume so that as
the playback volume is adjusted automatically, the perceived bass
response, tonal balance, surround impression, and dialog clarity
remain the same.
-Nti'.
• "Dynamic Volume" can only be set when auto setup has been
performed.
• "Dynamic Volume" cannot be set in the following situations.
• If "Auto Setup" fails to be completed.
• After running Auto Setup, when the number of used speakers has
increased from the number of measured speakers.
• When" MultEO" is set to "OFF", "Dynamic EO" is automatically set
to "OFF".
• "Night Mode" and "Tone Control" cannot be used jointly.
[Selectable items]
ON
Use Dynamic Volume.
The Dynamic Volume effect will be at the level of the "DV
Setting".
~:
Do not use Dynamic Volume.
~
Operating from the main unit or main remote
~
control unit
> . - - - - - - -
<DYN VOl>
Press or
I
Dynamic EO Volume: ON - - Dynamic EO : ON / Volume: OFF
[~\i.'2~~~!'J]
~«-
[DYNAMIC
or
"Green"
Before running Auto Setup and after running Auto Setup, if the number
of speakers has increased or you pressed
VOLUME],
"Run Audyssey" is displayed. In this case, either perform
Auto Setup again, or return to the setting after running Auto Setup with
"System Setup" - "Speaker Setup" - "Restore".
)
For details on adjusting individual parameters, see "Adjusting the parameters" (D3f"page 33).1
[DYNAMIC VOLUME].
[~\i.'2~~~!'J]
~-
"Red"
Dynamic EO / Volume: OFF
<DYN VOl> [DYNAMIC
or
fi1
DV Setting (Dynamic Volume Setting)
Set Dynamic Volume effect.
[Selectable items]
I I:
Midnight
High setting affects volume the most. causing all sounds
to be of equal loudness.
Evening
Middle setting prevents loud and soft sounds from
being much louder and softer respectively than average
sounds.
Day Low setting provides the least adjustments to the
loudest and softest of sounds.
-Nti'•
• "DV Setting" can only be set when auto setup has been performed.
• "DV Setting" cannot be set in the following situations.
• If "Auto Setup" fails to be completed.
• After running Auto Setup, when the number of used speakers has
increased from the number of measured speakers.
• If "Dynamic Volume" setting is "OFF':
Abo.ut Dynamic EQ
Audyssey Dynamic EOTM solves the problem of deteriorating sound
quality as volume is decreased by taking into account human
perception and room acoustics. Dynamic EO selects the correct
frequency response and surround levels moment-by-moment at
any user-selected volume setting. The result is bass response,
tonal balance, and surround impression that remain constant
despite changes in volume. Dynamic EO combines information
from incoming source levels with actual output sound levels in the
room, a prerequisite for delivering a loudness correction solution.
Audyssey Dynamic EO works in tandem with Audyssey MultEO to
provide well-balanced sound for every listener at any volume level.
About Dynamic Volume
Audyssey Dynamic Volume™ solves the problem of large variations
in volume level between television programs, commercials, and
between the soft and loud passages of movies.
Dynamic Volume looks at the preferred volume setting by the user and
then monitors how the volume of program material is being perceived
by listeners in real time to decide whether an adjustment is needed.
Whenever necessary, Dynamic Volume makes the necessary rapid
or gradual adjustments to maintain the desired playback volume
level while optimizing the dynamic range Audyssey Dynamic EO is
integrated into Dynamic Volume so that as the playback volume is
adjusted automatically, the perceived bass response, tonal balance,
surround impression, and dialog clarity remain the same whether
watching movies, flipping between television channels, or changing
from stereo to surround sound content.
ENGLISH
-1
o
c
u
' "
' "
LI
36