Sony HCD-J3MD Service Manual page 37

9. Press the ENTER/YES "R" button and display "EFB =
MO-P".Then, the optical pick-up moves to the pit area
automatically and servo is locked.
10. Observe the waveform of the oscilloscope, and check that the
specified value is satisfied. Do not press the lm/TUNING
– button or ML/TUNING + button.
(Traverse Waveform)
VC
Specified value : 10% or less of the offset value
IA – BI
Offset value (%) =
2 (A + B)
11. Press the ENTER/YES "R" button and display "EF MO CHECK"
The disc stops rotating automatically.
12. Press the A (MD) button and remove the disc.
13. Load the check disc (MD) TDYS-1.
14. Press the ML/TUNING + button and display "EF CD
CHECK".
15. Press the ENTER/YES "R" button and display "EFB =
CD". Servo is locked automatically.
16. Observe the waveform of the oscilloscope, and check that the
specified value is satisfied. Do not press the lm/TUNING
– button or ML/TUNING + button.
(Traverse Waveform)
VC
Specified value : 10% or less of the offset value
IA – BI
Offset value (%) =
2 (A + B)
17. Press the ENTER/YES "R" button and display "EF CD
CHECK".
18. Press the A (MD) button and remove the check disc (MD)
TDYS-1.
Note 1 : MO reading data will be erased during if a recorded disc is
used in this adjustment.
Note 2 : If the traverse waveform is not clear, connect the
oscilloscope as shown in the following figure so that it can
be seen more clearly.
BD (MD) board
CN110 pin 3 (TE)
CN110 pin 1 (VC)
X 100
X 100
Oscilloscope
330 kΩ
10pF
5-6-4. Focus Bias Check
Change the focus bias and check the focus tolerance amount.
Checking Procedure :
1. Load a test disk (MDW-74/AU-1).
2. Press the lm/TUNING – button or ML/TUNING
+ button and display "CPLAY MODE".
3. Press the ENTER/YES "R" button twice and display "CPLAY
MID".
4. Press the MENU/NO "R" button when "C1 =
is displayed.
5. Press the lm/TUNING – button or ML/TUNING
A
+ button and display "FBIAS CHECK".
6. Press the ENTER/YES "R" button and display "
B
".
The first four digits indicate the C1 error rate, the two digits
after "/" indicate ADER, and the 2 digits after "c =" indicate the
focus bias value.
Check that the C1 error is 50 or less and ADER is 2 or less.
7. Press the ENTER/YES "R" button and display "
".
Check that the C1 error is 220 or less and ADER is 2 or less.
8. Press the ENTER/YES "R" button and display "
".
Check that the C1 error is 220 or less and ADER is 2 or less.
9. Press the MENU/NO "R" button, next press the A (MD)
button, and remove the test disc.
5-6-5. C PLAY Checking
MO Error Rate Check
Checking Procedure :
1. Load a test disk (MDW-74/AU-1).
2. Press the lm/TUNING – button or ML/TUNING
+ button and display "CPLAY MODE".
3. Press the ENTER/YES "R" button and display "CPLAY MID".
4. The display changes to "C1 =
A
5. If the C1 error rate is 50 or less, check that ADER is 2 or less.
6. Press the MENU/NO "R" button, stop playback, press the A
(MD) button, and test disc.
B
CD Error Rate Check
Checking Procedure :
1. Load a check disc (MD) TDYS-1.
2. Press the lm/TUNING – button or ML/TUNING
+ button and display "CPLAY MODE".
3. Press the ENTER/YES "R" button twice and display "CPLAY
MID".
4. The display changes to "C1 =
5. Check that the C1 error rate is 20 or less.
6. Press the MENU/NO "R" button, stop playback, press the A
(MD) button, and the test disc.
5-6-6. Self-Recording/playback Check
Prepare a continuous recording disc using the unit to be repaired
and check the error rate.
Checking Procedure :
1. Insert a recordable disc (blank disc) into the unit.
2. Press the lm/TUNING – button or ML/TUNING
+ button to display "CREC MODE".
3. Press the ENTER/YES "R" button to display the "CREC MID".
4. When recording starts, z MD indicator lights up displayed,
this becomes "CREC (@@@@)" (@@@@ is the address), and
recording starts.
5. About 8 seconds later, press the MENU/NO "R" button to stop
continuous recording.
6. Press the lm/TUNING – button or ML/TUNING
+ button to display "C PLAY MODE".
7. Press the ENTER/YES "R" button to display "C PLAY MID".
AD = "
/ c =
/ b =
/ a =
AD = ".
AD = ".
37