PIONEER Service Manual. A subscription to, or additional copies Also test with plug reversed of, PIONEER Ser vice Manual may be obtained at a (Using AC adapter Earth nominal charge from PIONEER. plug as required)
Page 3
2. When the cover is open, close viewing through the objective lens with the naked eye will cause exposure to the laser beam. ∗ : See page 28. /C LO M EN M EN DV-300-K...
Page 4
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. DV-300-K...
• Soldering time: Within 3 seconds • Soldering combination: Sn-3.0Ag-0.5Cu • When Soldering/Removing of solder, use the draw in equipment over the Pick Up Unit to prevent the Flux smoke from it. Short circuit using a soldering iron. Pick Up PCB Fig. 1 DV-300-K...
• Place the unit on a workstation equipped to protect against static electricity, such as conductive mat. • Soldering iron with ground wire or ceramic type is used. • A worker needs to use a ground conductive wrist strap for body. DV-300-K...
DVD-R/RW compatibility • Compatible formats: DVD-Video, Video Recording (VR)* * Edit points may not play exactly as edited; screen may go momentarily blank at edited points. • Unfinalized playback: No • WMA/MP3/JPEG file playback on DVD-R/ RW: No DV-300-K...
Page 11
In these particular instances, check with the software publisher for more detailed information. Discs recorded in packet write mode (UDF format) are not compatible with this player. Check the DVD-R/RW or CD-R/RW software disc boxes for additional compatibility information. DV-300-K...
Returns to the previously dis-played menu screen. • Press to jump to the previous/next 7 HOME MENU chapter or track. 8 Display Compatible Description of the display. This mark indicates compatibility with DVD-RW discs recorded on a DVD recorder in Video Recording mode. DV-300-K...
Page 13
Press to pause playback; press again to restart. 12 PLAY MODE Press to display the Play Mode menu. (You can also get to the Play Mode menu by pressing HOME MENU and selecting Play Mode). Press to jump to the beginning of the current DV-300-K...
Page 14
Use to select menu options, etc. playing. 18 MENU 24 ZOOM Press to display a DVD disc menu, or the Disc Press to change the zoom level. Navigator if a VR format DVD-RW, CD, Video CD , MP3, WMA or JPEG disc is loaded. DV-300-K...
Items to be checked regarding video Item to be checked regarding audio Block noise Distortion Horizontal noise Noise Dot noise Volume too low Disturbed image (video jumpiness) Volume too high Too dark Volume fluctuating Too bright Sound interrupted Mottled color DV-300-K...
• Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools: Position to be cleaned Position to be cleaned Cleaning tools Cleaning tools Remark Remark Pickup leneses Cleaning liquid : GEM1004 Cleaning paper : GED-008 DV-300-K...
-28V DPF015 CAUTION ATTENTION :SINCE THESE PARTS MARKED BY :LES PIECES REPAREES PAR UN ETANT CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE DESCRIBED IN PARTS LIST ONLY N'UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES DV-300-K...
BCZ3B05 LOAD+ LOADING MOTOR(-) SW-1(OPEN) OPEN GND(SW) SSS-28-5 CLOSE SW-2(CLOSE) PCB610 DED021 DVD MECHA ASSY (A2K001A650) DVD MT PCB PCB130 DMF089 NOTE: THIS INTERCONNECTION DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DV-300-K...
DECK DOES NOT ACCEPT OPEN/CLOSE Is the voltage at Check P.CON 6V line of pin 8 and 19 of IC2301 POWER BLOCK. about DC6V ? Check CD2302 Is the lose connection connection to DECK. at CD2302 to DECK ? Change DVD LOADER. DV-300-K...
Page 24
Replace V651 or IC651. NO PLAYBACK PICTURE OF AV JACK Is there Check IC4001 and a signal at pin 164 of peripheral circuit. IC4001 ? Is there Check J7302 and peripheral video signal at pin 33 circuit. of IC7301 ? Change IC7301. DV-300-K...
Page 25
NO ANALOG AUDIO ON PLAYBACK Is there Check J8003 and peripheral AUDIO signal at pins 1 and 7 circuit. of IC8003 ? Is there Check AT pins 184 and AUDIO signal at C8051 186 of IC4001. and C8053 ? Change IC8003. DV-300-K...
Page 26
Any kind of symptoms (no power, a failure in any of the servo, video and audio systems, etc.) may be (DVD MT PCB Assy : IC4001) generated, because the DVD processing is performed by a single chip. 64M SDRAM No power. (DVD MT PCB Assy : IC4005) Block noise is generated during playback. DV-300-K...
Assy. If the voltage is 0.4 V or higher, the 780-nm LD is degraded. DVD MT PCB ASSY CP2301 C2301 Q2307 Q2306 CP2303 Q2302 C4094 Q2301 Q2304 4006 W806 R2322 C4096 IC2301 R2329 R2319 C2317_1 R2311 W802 R2316 R4009 R4010 Front side SIDE A DV-300-K...
• After going into service mode, if you play back the disc, "DISC-NON" is displayed. • The video signal and the audio signal are outputted during the servicemode. • The SKIP key and the SCAN key are effective during the service mode. SERVICE MODE: OFF POWER GGF1381 Service mode remote control unit DV-300-K...
3 LD ON DVD : Press the [TEST] (A8-5E) and [1] (A8-01) keys in order, and turn on the laser diode (650n). : Press the [TEST] (A8-5E) and [4] (A8-04) keys in order, and turn on the laser diode (780n). DV-300-K...
: [NTSC] PAL system : [PAL] Automatic setting : [AUTO] Scart terminal output [SK – ∗ ∗] (Display only the WY model which can do the output setting of scart terminal.) VIDEO : [00] S-VIDEO : [01] : [02] DV-300-K...
• Region confirmation mode (ESC + A.MON [Service mode remote control unit] + "1"-"8" [Service mode remote control unit] keys) After you press the A.MON key while holding the ESC key pressed and then input the region number, if the number is different from that set in the unit, an error message is displayed, and the tray opens. DV-300-K...
%%e -2 : NG 7.0e -4 : NG 3 EDC/ID error history (ID Address, EDC/ID errors, last eight errors) Note: ∗ Error of AV1 is not supported in this player. Indication plan contents Character in bold : Item name : Information display DV-300-K...
Up PCB and DVD MT PCB connector. 1-4: DVD MT PCB (Refer to Fig. 1-4) 1. Remove the 4 screws 1. 2. Remove the 4 screws 2. 3. Remove the DVD MT PCB in the direction of arrow. Fig. 1-2 DVD MT PCB Fig. 1-4 DV-300-K...
Page 35
3 supports 1. between A and B. Fig. 2-3-D 2. Remove the Plate Clamper, Magnet Clamper and Clamper. Check Hook Check Hook Plate Clamper Magnet Clamper Main Frame Loading Motor PCB Ass’y Check Hook Clamper Fig. 2-3-E Fig. 2-5-A DV-300-K...
Page 36
6. Remove the Switch PCB Ass'y. 7. Remove the screw 4. Feed Motor 8. Remove the Gear Feed. 9. Remove the 2 screws 5. 10. Remove the Feed Motor. Safety surface for pressing 11. Remove the Gear Motor. of the insert. Fig. 2-7-C DV-300-K...
Page 37
Fig. 2-8. NOTE 1. Do not make the folding lines except the specified positions for the FFC. [ 24 pin FFC ] Fold Printing Surface 79 ± 1 mm Reinforcement Plate To Pick Up PCB Fig. 2-8 DV-300-K...
While the screen shown at left is being displayed, updating is in progress. DO NOT TURN OFF THE POWER DURING UPDATING. 4 Updating of the firmware is completed. When the screen with the Pioneer logo is displayed, updating is completed. The time required for updating is about 2 minutes. DV-300-K...
Page 39
2 If updating of the firmware using the disc for updating failed • Was the disc for updating recognized properly? Check if the volume label of the disc is PIONEER. • Is playback of a disc other than the disc for updating possible? If playback of a test CD is also impossible, a reading section, such as PU, may be defective.
Screws adjacent to mark on product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 9.1 PACKING SECTION DV-300-K...
Note : (SW PCB ASS'Y) CD2301 NOTE: Applying positions AA, AB and AC for the CLASS PART NO. MARK grease are displayed for this section. GREASE GEM1018 Check if the correct grease is applied for each GYA1001 position. GEM1036 DV-300-K...
55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 DQ11 DQ12 DQ13 DQ14 DQ15 DBA0 DBA1 MA10 MA11 SDCKE SDCLK 1.8V NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-300-K...
Page 47
R4037 10K TP4035 TP4092 R4075 R4039 10K RESET TP4093 TP4094 C4118 (V+3D) 100P CH NR4001 4D03WGJ0330T5E B4011 PCB130 MMZ1608R102CT DMF089 R4076 NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME AYBACK. OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DV-300-K...
PCE# PRD# PCE# PWR# FROM POWER PORT (V+3D) D_GND NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DURING PLAYBACK. DV-300-K...
Page 49
÷ The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. ÷ : The power supply is shown with the marked box. DV-300-K...
W802 C2311 CAUTION ATTENTION :SINCE THESE PARTS MARKED BY :LES PIECES REPAREES PAR UN ETANT CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE DESCRIBED IN PARTS LIST ONLY N'UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES DV-300-K...
Page 51
W805 VOLD+ VOSL- VOTK- VOFC- VOTK+ VOFC+ PCB130 NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME DMF089 OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-300-K...
FROM VIDEO JACK V+5V_A NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME CAUTION :SINCE THE MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE CRITICAL DURING PLAYBACK. DESCRIBE DV-300-K...
Page 53
PCB130 ATTENTION CAUTION :LES PIECES REPAREES PAR UN ETANT :SINCE THESE PARTS MARKED BY DMF089 DANGEREUSES AN POINT DE VUE SECURITE CRITICAL FOR SAFETY,USE ONES N'UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST ONLY DANS LA NOMENCLATURE DES PIECES DV-300-K...
FROM POWER PORT 22uH 0405 V+5V_A V+5V TP7303 D_GND D_GND NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DURING PLAYBACK. DV-300-K...
Page 55
W877 TP7301 W801 S_C OUT S_Y OUT CVBS OUT S-VIDEO OUT CVBS/Y/U/V J7301 J7302 DIN-409A RCA-405A-08 CAUTION: DIGITAL TRANSISTOR PCB130 DMF089 DV-300-K...
FL DC+ -28V ATTENTION CAUTION :LES PIECES REPAREES PAR UN ETANT :SINCE THESE PARTS MARKED BY DANGEREUSES AN POINT DE VUE SECURITE CRITICAL FOR SAFETY,USE ONES N'UTILISER QUE CELLS DECRITES DESCRIBED IN PARTS LIST ONLY DANS LA NOMENCLATURE DES PIECES DV-300-K...
Page 57
FLDC- FLDC+ -28V D_GND TO MEMORY D_GND PCB130 DMF089 NOTE:THE DC VOLTAGE EACH PART WAS NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME MEASURED WITH THE DIGITAL TESTER OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DURING PLAYBACK. DV-300-K...
LED3 SW666 -18.0 GR10 LED2 EVQ11L05R -18.0 GR11 LED1 -18.0 -18.0 -18.0 -16.0 -16.0 -16.0 -16.0 -16.0 -16.0 C659_1 100P CH Vout R666 1/4W OS651 ROM-V340TAO NOTE:THE DC VOLTAGE EACH PART WAS MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK. DV-300-K...
Page 59
2H0B1003 V+3E V+3E V+3E C604 DGND C605 33P CH DGND TP663 FLDC+ 0.001 B FLDC+ -28V -28V FLDC- FLDC- NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME PCB270 OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE ESTER DEF126 DV-300-K...
NOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME CRITICAL FOR SAFETY,USE ONES DANGEREUSES AN POINT DE VUE SECURITE OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE DESCRIBED IN PARTS LIST ONLY N'UTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES DV-300-K...
Page 61
CAUTION: DIGITAL TRANSISTOR LATEST AT THE TIME NOTE:THE DC VOLTAGE EACH PART WAS NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. HANGE WITHOUT NOTICE MEASURED WITH THE DIGITAL TESTER THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP DURING PLAYBACK. IS NON POLAR ONE. DV-300-K...
B C E Field effect SIDE B P.C.Board Chip Part transistor Resistor array 3-terminal regulator 11.1 LOADING MOTOR/SW LOADING MOTOR (INSERTED PARTS) LOADING MOTOR (CHIP MOUNTED PARTS) SOLDER SIDE SOLDER SIDE DED021A M2603 CD2302 DED021A SOLDER SIDE DED020A M2602 M2601 DV-300-K...