Related Manuals for LG MFL67652408
Summary of Contents for LG MFL67652408
- Page 1 Owner's Manual Laser Display install guide Please read the safety information carefully before using the product. www.lg.com P/NO : MFL67652408(1302-REV00)
-
Page 2: Safety Precautions
Safety Precautions Safety Precautions Please take note of the safety instructions to prevent any potential accident or misuse of the product. Safety precautions are given in two forms, i.e. Warning and Caution as detailed be- low. WARNING: Failure to follow the instructions may cause serious injury and even death. - Page 3 Safety Precautions When drilling the holes in the wall, make sure you use a drill and a drill bit with the specified size of diameter. Ensure that you also follow the in- structions regarding the depth of the holes. - Otherwise, the product may be installed improperly causing safety issues.
- Page 4 PREPARATION PREPARATION Accessories Check the accessories provided with the product. The picture may be different from the actual product. Accessories are subject to change without prior notice in order to improve the perfor- mance of the product. New accessories may be added or old ones may be removed. Connection rods, Rubber Ez Bracket...
-
Page 5: Installation
INSTALLATION INSTALLATION How to fix anchors and screws CAUTION y Check the wall materials and the thickness of finishing materials. y You can use the anchors and bolts provided with the Laser Display set for walls made from concrete, lightweight concrete, soft fieldstone, hard fieldstone, brick or cellular blocks. - Page 6 INSTALLATION Installation Procedure (Stand Type) Install the guide pins at the bottom of the set. Connect the connection rod to the Ez bracket main unit and place it on a table, without the fixed components, at the center of the screen. NOTE y Do not assemble the fixed components to the unit yet.
- Page 7 INSTALLATION If the Ez bracket does not stay level, attach a rubber to the bottom of the bracket to make it level. (If you cannot make it level using a rubber, remove or add a plate. To add a plate, make sure to use screws that came with the product.) NOTE y If you cannot make it level by attaching a rubber, remove or add a plate.
- Page 8 INSTALLATION Attach 390 mm of guide tapes to the top of the table referring the sides of Laser Display so that the tapes are vertically upward. Center line Paper screen Down 390 mm Guide tape Adjustable bracket Table NOTE The figure above illustrates the fixed components which are not fixed yet. Attach the paper screen above the tape.
- Page 9 INSTALLATION Adjust the Ez bracket by following the Laser Display screen adjustment steps to make the size of the projection screen equal to that of the paper screen. Position the projection screen, aligning it with the black line of the paper screen. (If there is a gap larger than 10 mm between the projection screen and the paper screen, mark the screen position on the paper screen and make holes in four places.)
- Page 10 INSTALLATION Place guide tape on both sides of the paper screen in parallel with it. Position the tape about 40 mm above the paper screen. The tape is used as a reference guide to help easy screen installation. 40 mm Tape Down Make holes using an 8 mm drill at specified positions and detach the paper screen.
- Page 11 INSTALLATION Mark the end of Ez bracket rod on the wall. (Mark the positions of the holes where the Ez brackets will be fixed.) Remove the Laser Display set and Ez bracket from the table. 16 Position both holes of the fixed component against the marks on the wall and mark the positions where the anchors will be inserted.
- Page 12 INSTALLATION Make holes in the two locations marked with arrows using an 8 mm drill. Detach the paper screen and insert the anchors into the two holes. 19 Secure the fixed component using two 8 mm screws. (If adjustment is not possible due to lack of marginal space while aligning an image to the screen, loosen the screws and move the fixed component slightly to the left or right.) Fix the Ez bracket to the fixed component using the spanner and fixing nuts...
- Page 13 INSTALLATION Two people must lift the screen above the guide tape and hang it on the rings. Keep the arrows pointing down. CAUTION y Align the top of screen with the top of the tape and the left and right sides of the screen with the tape.
- Page 14 INSTALLATION CAUTION • If the screen is tilted when pulling it down, it may not fix to the bracket and could result in damage to the screen. Move the screen in all directions to check that it is securely hung on the rings. Check whether the screen stays level using a leveler.
- Page 15 INSTALLATION Check that the right and left sides of the screen are parallel to the wall using a leveler.If it is not parallel to the wall, calibrate the screen angle using the space steels. Unhang the screen and remove the fixed rings and magnets. Calculate the amount of space steels to be used using the formula below, locate the space steels between the wall and the rings/magnets and fix them again, and align the screen to be parallel to the wall.
- Page 16 INSTALLATION If the screen is not parallel to the wall NOTE If the top of the screen is tilted to the wall, add space steels at the top and, if the bottom of screen is tilted to the wall, add magnets at the bottom to make the screen parallel to the wall. If the screen does not stay level If you want to move the screen vertically or if it does not stay level, remove the screen and adjust the bracket on the back.
- Page 17 INSTALLATION * If the screen is tilted to the right as shown below, fix the left bracket screw to a higher hole or fix the right bracket screw to a lower hole. Refer to the screen adjustment steps to align the image from the Laser Display to the screen.
- Page 18 INSTALLATION Ez Bracket Adjustment Guide 1. Reset projection * Press the Edge Adj button on the remote control and select Reset. (Select Settings → OPTION → Edge Adj → Reset to reset the position of the projection.) OPTION ︿ • Language • ...
- Page 19 INSTALLATION Insert the hex wrench into the hole as illustrated (left) and turn it clockwise to move the pro- jection to the right. CAUTION y If you are using a paper screen, align the paper screen with the projection and reattach it to the wall rather than moving the projection to the left or right.
- Page 20 INSTALLATION 4. Adjust the horizontal line of the projection to be parallel with the width of the screen To turn the projection clockwise Turn the left control panel counterclockwise and turn the right control panel clockwise. To widen the left width of the projection and narrow the right width Turn the left control panel counterclockwise and turn the right control panel clockwise.
- Page 21 INSTALLATION 5. Adjust the top and bottom widths of the projection so they are equal To narrow the top width of the projection and widen the bottom width Turn the left and right control panels counterclockwise simultaneously. * Length A = Length B To widen the top width of the projection and narrow the bottom width Turn the left and right control panels clockwise simultaneously.
- Page 22 INSTALLATION 6. If the projection is rectangle-shaped, Enlarge the projection to fit the screen size Insert the hex wrench into the hole as illustrated (left) and turn it clockwise to enlarge the size of the projection. To move the projection to the left Insert the hex wrench into the hole as illustrated (left) and turn it counterclockwise to move the projection to the left.
- Page 23 INSTALLATION 7. When the projection is the same size as the screen, fine-tune the projection location using Edge Adj function * Complete fine tuning by pressing the Edge Adj button on the remote control. (Press the MENU button on the remote control and select Edge Adj in OPTION.) OPTION ︿...