Advertisement
Before you start...
Your safety and the safety of
others are very important.
Ne have provided many important
safety messages in this manual
and on your appliance. Always
read and obey all safety messages.
This is the safety alert
symbol.
This symbol alerts you to
potential hazards that can kill or
hurt you and others.
All safety messages will follow the
safety alert symbol and either the
word "DANGER" or "WARNING".
These words mean:
You can be killed or seriously
injured if you don't immediately
follow instructions.
You can be killed or seriously
injured If you don't follow
instructions.
All safety messages will tell you
what the potential hazard is, tell you
how 1o reduce the chance of injury,
and tell you what can happen if the
instructions are not followed.
It is your ..
responsibdRyto:
Observe all governing codes and
ordinances.
Check code requirements: Some
codes limit or do not permit
installation of this product in garages,
closets, mobile homes or sleeping
quarters. Contact your local building
inspector.
Comply with the installation
specifications and dimensions.
Consider spacing requirements for
companion appliances.
Make sure you have everything
necessary for proper installation.
Properly install appliance.
Contact a qualified installer to insure
that the electrical installation meets
all national and local codes and
ordinances.
PAGE 2
Electrical
requirements
Electrical Shock Hazard
Plug into a grounded 3-prong
outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these
instructions can result in death,
fire, or electrical shock.
4
Important: Observe all governing
codes and ordinances.
A 120-volt, 60-Hz, AC-only, 15- or
20-ampere fused electrical supply is
required. A Time-delay fuse or circuit
breaker is recommended,
It is recommended that a separate
circuit serving only this appliance be
provided.
If codes permit and a separate
ground wire is used, it is
recommended
that a qualified
electrician determine that the
ground path is adequate.
3-prong ground-type
outlet must
be located within 5 feet of lower
right corner of appliance.
Recommended
ground method
The clothes vitalizer, when installed,
must be electrically grounded in
accordance with local codes, or in
the absence of local codes, with
National Electrical Code, ANSI/
NFPA 70".
GROUNDING
INSTRUCTIONS:
This
clothes vitalizer must be grounded. In
the event of malfunction or
breakdown, grounding will reduce the
dsk of electdc shock by providing a
path of least resistance for electric
current.
The power supply cord plug must be
plugged into an appropriate outlet
that is properly installed and
grounded in accordance with all local
codes and ordinances.
WARNING - Improper connection
of the equipment-grounding
conductor can result in a risk of
electric shock. Check with a
qualified electrician or serviceman
if you are in doubt as to whether
the appliance is properly
grounded. Do not modify the plug
provided with the appliance - if it
will not fit the outlet, have a proper
outlet installed by a qualified
electrician.
3-prong
goutlet
ground
^ A
plug __
r /
ground
/
prong
power
suppty
cord
Tools needed for
installation:
• stud finder (optional)
• drill (electric recommended)
• 5/32" drill bit (pilot hole for lag bolt)
• tape measure
• pencil
• carpenter's level
• 7/16" wrench (ratchet
recommended) for lag bolts
if installing on a concrete or concrete
block wall
• concrete ddll bit for wall anchors
(refer to wall anchor for drill bit size)
• hammer
Parts supplied for
installabon:
(inside accessory box)
• 2, 1/4" x 2" lag bolts (for wood studs)
• 2, 1/4-20" nuts
• 1 mounting bracket cover (can be
painted or covered with wallpaper)
• separate metal mounting bracket
assembly
• 6, 1/8=thick adhesive backed cabinet
spacers
Copies of the standards listed above may be
obtained from:
• National Fire Protection AasodalJon
One Batterymardn Park
Quincy, Massachusetts
02269
Advertisement
