Vector VEC1043 User Manual
  1. Manuals
  2. Brands
  3. Vector Manuals
  4. Inverter
  5. VEC1043
  6. User manual

Vector VEC1043 User Manual

750 watt vehicle power system converts dc vehicle power to 115 volt ac household power
Hide thumbs
1
2
3
4
5
6

Advertisement

Table of Contents

VEC1043_ManualEN_091505
1/17/06
Fault Protection Code and Troubleshooting Guide
INVERTER POWER SWITCH TURNED ON
Trouble/Indication
Possible Cause
No AC output — yellow
DC input is below
LED lit
10 volts
No AC output — red LED
Excessive appliance
lit
load
Inverter hot
No AC output — green
Bad connection or
LED not lit
wiring
Low battery alarm sounds
Low battery voltage
Motorized power tool will
Excessive start-up load If appliance does not start,
not operate
Motorized power tool
Purely inductive load
does not operate at
correct speed
Television/radio
Snow in picture,
interference
"buzzing" sound
SPECIFICATIONS
Output Connection:
North American standard outlet
Output Voltage:
Approx. 115 volts AC, RMS 60 Hz
Output Current:
6.5 amps Max
Output Waveform:
Modified Sine Wave
Input Voltage:
12.5 volts DC
Low Voltage Alarm:
11.0 volts DC
No Load Input Current: 0.7 amps max.
Input Fuses:
Internal
Input Cables:
Battery clip cables
Additional Protection:
Overload, overvoltage, overheating
5:49 PM
Page 8
Suggested Remedy
Recharge or replace the
battery.
Reset unit by turning OFF,
then back ON.
Disconnect load from
inverter. Operate inverter
without load for a few
minutes. Reconnect load.
Tighten all DC connections.
Recharge battery. Remove
load from inverter while
recharging battery.
appliance is drawing too
much voltage and will not
work with this inverter.
Make the load not purely
inductive (i.e., operate an
incandescent lamp at the
same time as power tool).
Keep inverter and antenna
distant from each other.
Use shielded antenna.
Connect antenna to
amplifier.
8
750 Watt
Power Inverter
Vehicle Power System
Converts DC Vehicle Power
to 115 Volt AC Household Power
USER'S MANUAL
& WARRANTY INFORMATION
I I I I M M M M P P P P O O O O R R R R T T T T A A A A N N N N T T T T S S S S A A A A F F F F E E E E T T T T Y Y Y Y I I I I N N N N F F F F O O O O R R R R M M M M A A A A T T T T I I I I O O O O N N N N , , , , S S S S A A A A V V V V E E E E T T T T H H H H E E E E S S S S E E E E I I I I N N N N S S S S T T T T R R R R U U U U C C C C T T T T I I I I O O O O N N N N S S S S
TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND
THIS INSTRUCTIONAL MANUAL. THIS MANUAL CONTAINS IMPORTANT
INFORMATION REGARDING THE OPERATION AND WARRANTY OF THIS
PRODUCT. PLEASE RETAIN FOR FUTURE REFERENCE.
4140 S.W. 30th Ave., Ft. Lauderdale, FL 33312
Toll Free: (866) 584-5504
www.vectormfg.com
VEC1043

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VEC1043 and is the answer not in the manual?

Questions and answers

Related Manuals for Vector VEC1043

Summary of Contents for Vector VEC1043

  • Page 1: Warranty Information

    VEC1043_ManualEN_091505 1/17/06 5:49 PM Page 8 Fault Protection Code and Troubleshooting Guide VEC1043 INVERTER POWER SWITCH TURNED ON Trouble/Indication Possible Cause Suggested Remedy No AC output — yellow DC input is below Recharge or replace the LED lit 10 volts battery.

  • Page 2: Important Safety Instructions

    Therefore, the installer/operator should be especially Vector products must be regi s tered wi t hi n 30 days of purchase to acti v ate thi s warranty. Mai l the compl e ted...

  • Page 3: Controls, Indicators, And Connectors

    Principle of Operation ......... . 2 The VEC1043 supplies 750 watts of continuous power, in the form of two standard The Power Inverter Output Waveform .

  • Page 4: How This Inverter Works

    VEC1043_ManualEN_091505 1/17/06 5:49 PM Page 2 inverter, the red LED indicates inverter shutdown from an over-load or over- not read the RMS voltage of a modified sine wave correctly. They will read about 20 temperature fault and the yellow LED indicates an input fault. In addition to turning to 30 volts low when measuring the output of the inverter.
  • Page 5 They only operate properly from a standard household 3. Connect the BLACK cable to the BLACK post marked (–) on the back of the outlet which provides a pure sine wave. Therefore, Vector inverter. Connect the battery clip to the NEGATIVE terminal of the battery.

  • Page 6: Care And Maintenance

    In most instances, 5 to 10 hours of operating time is achievable. However, Some inexpensive stereo systems and “boom boxes” emit a buzzing sound from their Vector recommends that the operator start the vehicle every half hour to recharge the speakers when operated from the Power Inverter. This occurs because the power battery system.

Table of Contents