Leviton LV200 User Manual

Limited Warranty

Limited Warranty Limited Warranty
LEVITON LIGHTING CONTROL DIVISION of Leviton
LEVITON LIGHTING MANAGEMENT
Manufacturing Co Inc. warrants its Dimmer Systems and
LEVITON LIGHTING CONTROL DIVISION of Leviton
DIVISION of Leviton Manufacturing Co Inc. warrants its
Controls to be free of material and workmanship defects
Manufacturing Co Inc. warrants its Dimmer Systems and
Dimmer Systems and Controls to be free of material and
for a period of two years after system acceptance or 26
Controls to be free of material and workmanship defects
workmanship defects for a period of two years after system
months after shipment, whichever comes first. The Z-MAX
for a period of two years after system acceptance or 26
acceptance or 26 months after shipment, whichever comes
Relay cards are covered for a period of Ten (10) years.
months after shipment, whichever comes first. The Z-MAX
first. The Z-MAX Relay cards are covered for a period of Ten
Lighting fixtures manufactured by Leviton are covered for a
Relay cards are covered for a period of Ten (10) years.
(10) years. Lighting fixtures manufactured by Leviton are
period of one year. This Warranty is limited to repair or
Lighting fixtures manufactured by Leviton are covered for a
covered for a period of one year. This Warranty is limited
replacement of defective equipment returned Freight Pre-
period of one year. This Warranty is limited to repair or
to repair or replacement of defective equipment returned
Paid to Leviton Lighting Control Division at 20497 SW
replacement of defective equipment returned Freight Pre-
Freight Pre-Paid to Leviton Lighting Management Systems
Teton Ave., Tualatin, Oregon 97062, USA. User shall call
Paid to Leviton Lighting Control Division at 20497 SW
Division at 20497 SW Teton Ave., Tualatin, Oregon 97062,
1-800-959-6004 and request a return authorization number
Teton Ave., Tualatin, Oregon 97062, USA. User shall call
USA. User shall call 1-800-959-6004 and request a return
to mark on the outside of the returning carton, to assure
1-800-959-6004 and request a return authorization number
authorization number to mark on the outside of the returning
that the returned material will be properly received at
to mark on the outside of the returning carton, to assure
carton, to assure that the returned material will be properly
Leviton. All equipment shipped back to Leviton must be
that the returned material will be properly received at
received at Leviton. All equipment shipped back to Leviton
carefully and properly packed to avoid shipping damage.
Leviton. All equipment shipped back to Leviton must be
must be carefully and properly packed to avoid shipping
Replacements or repaired equipment will be returned to
carefully and properly packed to avoid shipping damage.
damage. Replacements or repaired equipment will be
sender freight prepaid, F.O.B. factory. Leviton is not
Replacements or repaired equipment will be returned to
returned to sender freight prepaid, F.O.B. factory. Leviton
responsible for removing or replacing equipment on the job
sender freight prepaid, F.O.B. factory. Leviton is not
is not responsible for removing or replacing equipment
site, and will not honor charges for such work. Leviton will
responsible for removing or replacing equipment on the job
on the job site, and will not honor charges for such work.
not be responsible for any loss of use time or subsequent
site, and will not honor charges for such work. Leviton will
Leviton will not be responsible for any loss of use time or
Total # Button Station
damages should any of the equipment fail during the war-
not be responsible for any loss of use time or subsequent
subsequent damages should any of the equipment fail
Part # Buttons Label Terminal
ranty period, but agrees only to repair or replace defective
damages should any of the equipment fail during the war-
during the warranty period, but agrees only to repair or
equipment returned to its plant in Tualatin, Oregon. This
ranty period, but agrees only to repair or replace defective
replace defective equipment returned to its plant in Tualatin,
Zone 1 SW1/LD1
Warranty is void on any product that has been improperly
equipment returned to its plant in Tualatin, Oregon. This
Oregon. This Warranty is void on any product that has been
installed, overloaded, short circuited, abused, or altered in
Warranty is void on any product that has been improperly
Zone 2 SW2/LD2
improperly installed, overloaded, short circuited, abused, or
any manner. Neither the seller nor Leviton shall be liable
installed, overloaded, short circuited, abused, or altered in
altered in any manner. Neither the seller nor Leviton shall be
for any injury, loss or damage, direct or consequential aris-
any manner. Neither the seller nor Leviton shall be liable
Zone 3 SW3/LD3
liable for any injury, loss or damage, direct or consequential,
ing out of the use of or inability to use the equipment. This
for any injury, loss or damage, direct or consequential aris-
arising out of the use of or inability to use the equipment.
Warranty does not cover lamps, ballasts, and other equip- Zone 4 SW4/LD4
ing out of the use of or inability to use the equipment. This
This Warranty does not cover lamps, ballasts, and other
VS-08W 8
ment which is supplied or warranted directly to the user by
Warranty does not cover lamps, ballasts, and other equip-
equipment which is supplied or warranted directly to the user
Zone 5 SW6/LD6
their manufacturer. Leviton makes no warranty as to the
ment which is supplied or warranted directly to the user by
by their manufacturer. Leviton makes no warranty as to the
Fitness for Purpose or other implied Warranties.
their manufacturer. Leviton makes no warranty as to the
Fitness to Purpose or other implied Warranties.
Zone 6 SW7/LD7
Fitness for Purpose or other implied Warranties.
For Technical Assistance Call:
Zone 7 SW8/LD8
1-800-959-6004
For Technical Assistance Call:
www.colortran.com
Zone 8 SW9/LD9
1-800-959-6004
www.leviton.com
www.colortran.com
Zone 1 www.leviton.com SW1/LD1
I n s t a l l a t i o n R e q u i r e m e n t
Zone 2 SW2/LD2
O v e r v i e w
I n s t a l l a t i o n R e q u i r e m e n t
Installation Requirements
Zone 3 O v e r v i e w SW3/LD3
The switches are wired using analog wiring, requiring
Zone 4 SW4/LD4
1 wire for each switch leg, 1 optional wire for each
The switches are wired using analog wiring, requiring
As this is an analog system, any system topology is
LED indicator within each switch (if desired), 1
1 wire for each switch leg, 1 optional wire for each
Zone 5 SW5/LD5
VS-10W allowed. 10
optional wire for the locator LED and 1 wire for the
LED indicator within each switch (if desired), 1
Zone 6 SW6/LD6
device for common or +24V.
optional wire for the locator LED and 1 wire for the
device for common or +24V.
Zone 7 SW7/LD7
The "LOC"ator LED is illuminated when it is
As this is an analog system, any system topology is
connected to +24VDC.
Zone 8 SW8/LD8
allowed. Additionally, the low voltage switch can pro-
As this is an analog system, any system topology is
vide connections to common or +V upon a switch
allowed. Additionally, the low voltage switch can pro-
Zone 9 SW9/LD9
closure.
vide connections to common or +V upon a switch
closure. Zone 10 SW10/LD10
Typical connections to the device are as follows:
7
Typical connections to the device are as follows:
- The "SW_" terminals are connected to the
+24V/CM terminal when the switch is depressed.
- The "SW_" terminals are connected to the
+24V/CM terminal when the switch is depressed.
- The LED inside each switch illuminates when the
Securely mount the station to the wall using the
"LD_" terminal for the switch is connected to either
- The LED inside each switch illuminates when the
d screws.
+10-24V or Common (the opposite of that connected
"LD_" terminal for the switch is connected to either
to the +24V/CM terminal).
+10-24V or Common (the opposite of that connected
Mount the wall plate to the station.
to the +24V/CM terminal).
- The "LOC"ator LED is illuminated when it is con-
nected to either +10-24V or Common (the opposite
- The "LOC"ator LED is illuminated when it is con-
of that connected to the +24V/CM terminal.)
nected to either +10-24V or Common (the opposite
of that connected to the +24V/CM terminal.)
SYSTEMS
Low Voltage
Low Voltage
LV200
Switches
Switches
T e r m i n a l C o n n e c t i o n T y p e s Control Station
Depending on the needs of your equipment, the low volt-
age switch will support either closed circuit connection to Total # Button
common, or closed circuit +V. The chart below lists the Part # Buttons Label
options and requirements for the LD, LOC, and +24V/CM
Zone 1
ØØLVS-Ø1W ØØLVS-Ø2W ØØLVS-Ø3W
terminals.
ØØLVS-Ø1W ØØLVS-Ø2W
Zone 2
Zone 1
LV200
ON/OFF
Zone 1
Zone 2
Zone 3
ON/OFF
Zone 2
Station Zone 4
��
00LVS-08W 8
Terminal Wiring
ØØLVS-Ø5W ØØLVS-Ø6W ØØLVS-Ø8W
���
Zone 5
(00LVS-05W) Function Method #1
ØØLVS-Ø5W Zone 1 ØØLVS-Ø6W
������
Zone 2 Zone 1 Zone 4
Zone 6
Zone 1
Zone 3 Zone 2 Zone 5
���
SW_ Switch Output +24VDC
Zone 2 Zone 1 Zone 4
Zone 4 Zone 3 Zone 6
Zone 3 Zone 2
Zone 5 Zone 5
���
Zone 7
Zone 4
LD_ LED Input COMMON Zone 3 Zone 6
Zone 5
Zone 8
LOC Locator COMMON
Zone 1
+24V/CM Reference +24VDC
C u r r e n t D r a w
Zone 2
C u r r e n t D r a w
Electrical Requirements
Zone 3
The terminals will accept 14-24 GA wire.
At 24 VDC, each LED on the station, both those in the
Zone 4
buttons and the locator Led requires approximately
At 24 VDC, each LED on the station, both those in the Input Voltage: 24Vdc
7.5mA. Therefore the total load of each station is as fol-
buttons and the locator Led requires approximately Zone 5
00LVS-10W 10 Total #
lows:
7.5mA. Therefore the total load of each station is as fol-
Input Current: 24mA
Zone 6
Part # Buttons
lows:
Unit Load Consumption @
Zone 7
Station 24Vdc
Unit Load Consumption @
1 Unit Load = 25mA Zone 8
Station 24Vdc
1 Unit Load = 25mA
Environmental
Without
Zone 9
Locator LED
Without
Zone 10
Hooked Up
Locator LED
Operating Temperature Range:
00LVS-08W 8
Hooked Up
0 degrees C to 55 degrees C
1 Button 0.3
1 Button 0.3
Relative Humidity:
2 Button 0.6
20% to 90% non-condensing
P r o g r a m m i n g / O p e r a t i o n 2 Button 0.6
3 Button 0.9
Step 4: Securely mount the station to the wall using the
All System Programming, individual switch configuration, 3 Button 0.9
4 Button 1.2
provided screws.
and other device configuration options is performed at
4 Button 1.2
the device to which your switch is connected. 5 Button 1.5
Step 5: Mount the wall plate to the station.
5 Button 1.5
6 Button 1.8
6 Button 1.8
8 Button 2.4
8 Button 2.4
10 Button 3.0
10 Button 3.0
00LVS-10W 10
Remember to verify that the source of the
power for the low voltage stations is adequate in size for
Remember to verify that the source of the
the number of buttons and stations you have connected to
power for the low voltage stations is adequate in size for
it.
the number of buttons and stations you have connected to
3
it.
3
3
P r e c a u t i o n s a n d R e q u i r e m e n t s

Precautions and Requirements

P r e c a u t i o n s a n d R e q u i r e m e n t s
All standard precautions for wiring traditional low volt-
age control devices apply: All standard precautions for wiring traditional low
All standard precautions for wiring traditional low volt-
1. The cable should not pass near any source of elec-
voltage control devices apply:
age control devices apply:
trical noise or interface such as fluorescent circuits or 1. The cable should not pass near any source of
1. The cable should not pass near any source of elec-
motor wiring.
electrical noise or interface such as fluorescent trical noise or interface such as fluorescent circuits or
2. Close proximity to any AC wiring should be avoided
motor wiring.
circuits or motor wiring.
3. All analog wiring shall be in it's own conduit.
2. Close proximity to any AC wiring should be 2. Close proximity to any AC wiring should be avoided
4. Any wire type capable of carrying the required volt-
3. All analog wiring shall be in it's own conduit.
avoided.
age and current may be used
4. Any wire type capable of carrying the required volt-
3. All analog low voltage wiring shall be in it's own
5. Observe standard voltage drop calculations to
age and current may be used
conduit.
ensure that no less than +10 volts are received by the
5. Observe standard voltage drop calculations to
4. Any wire type capable of carrying the required
station Less than +10V and the LED's will not be
ensure that no less than +10 volts are received by the
voltage and current may be used.
bright enough to be seen or if voltage is quite low, may
station Less than +10V and the LED's will not be
5. Observe standard voltage drop calculations to
not light at all.
bright enough to be seen or if voltage is quite low, may
ensure that no less than +10 volts are received by the
not light at all.
T e r m i n a l C o n n e c t i o n T y p e s
W i r i n g a n d I n s t a l l a t i o n
station. Less than +10 and the LEDs will not be bright
enough to be seen or if voltage is quite low, may not
Step 1: If using a Decora Plus screwless wall plate,
Depending on the needs of your equipment, the low volt-
light at all.
remove the center tabs from the device as shown in
Station age switch will support either closed circuit connection to
the following figure:
Terminal common, or closed circuit +V. The chart below lists the
options and requirements for the LD, LOC, and +24V/CM
SW1/LD1
ØØLVS-Ø4W
terminals.
ØØLVS-Ø3W ØØLVS-Ø4W
SW2/LD2 Total #
Zone 1 Zone 1
Zone 2 Zone 2
Part # Buttons
Zone 1 Zone 3 Zone 1
Zone 3
SW3/LD3
Zone 2 Zone 2
Zone 4
Zone 3 Zone 3
SW4/LD4 Station
Zone 4
Wiring Terminal
ØØLVS-1ØW
SW6/LD6
Method #2 (00LVS-05W) Function
Zone 1 ØØLVS-Ø8W Zone 5 Zone 1 ØØLVS-1ØW Zone 6
Zone 2 Zone 6 Zone 2 Zone 7
SW7/LD7
Zone 1 Zone 5 Zone 1 Zone 6
Zone 3 Zone 7 Zone 3 Zone 8
COMMON SW_ Switch Output
Zone 2 Zone 6 Zone 2 Zone 7
Zone 4 Zone 8 Zone 4 Zone 9
Zone 3 Zone 7 Zone 3 Zone 8
Zone 5 Zone 10
SW8/LD8
00LVS-08W 8
Zone 4 Zone 8 LIT-32712-00 Rev A Zone 4 Zone 9
+24VDC LD_ LED Input
Zone 5 Zone 10
8/16/2004
LIT-32712-00 Rev A
DI-000-LV200-00A
SW9/LD9
+24VDC LOC Locator
Rev. A 8/2005
8/16/2004
SW1/LD1
COMMON +24V/CM Reference
T e r m i n a l / W i r e T e r m i n a t i o n
SW2/LD2
T e r m i n a l / W i r e T e r m i n a t i o n
Depending on the number of switches on your low voltage
SW3/LD3
The terminals will accept 14-24 GA wire. switch, different terminals at the rear are used for both the T e r m i n a l C o n n e c t i o n T y p e s
Depending on the number of switches on your low voltage
SW4/LD4
individual switch output and the switch LED input.
switch, different terminals at the rear are used for both the
Reference the following 3 tables for the specific required Depending on the needs of your equipment, the low volt-
individual switch output and the switch LED input.
SW5/LD5
Button Station
terminals. age switch will support either closed circuit connection to
Reference the following 3 tables for the specific required
SW6/LD6
Label Terminal common, or closed circuit +V. The chart below lists the
terminals.
options and requirements for the LD, LOC, and +24V/CM
+V to minZ ON
SW7/LD7
Zone 1 SW1/LD1
terminals.
Part #
SW8/LD8 00LVS-10W 10
Zone 2 SW2/LD2
+V to miniZ OFF
Part #
00LVS-01W
With Locator
SW9/LD9
Zone 3 SW3/LD3
00LVS-01W
LEDHooked
With Locator
+24Vdc
Zone 4 SW4/LD4 Station
SW10/LD10
Up
LEDHooked 00LVS-02W
Terminal
Up
00LVS-02W
Zone 5 SW6/LD6 8
7
(00LVS-05W)
Pilot
0.6
Zone 6 SW7/LD7
SW_
0.6
0.9
Common only if LED
00LVS-03W
Zone 7 SW8/LD8
P r o g r a m m i n g / O p e r a t i o n LD_
0.9
feedback is desired
00LVS-03W
1.2
Zone 8 SW9/LD9
All System Programming, individual switch configuration, This page left intentionally blank. LOC
1.2
+V, when +V
1.5
and other device configuration options is performed at
Zone 1 SW1/LD1
Location LED
+24V/CM
1.5
the device to which your switch is connected.
1.8
illuminates
Zone 2 SW2/LD2
1.8 00LVS-04W
2.1
Step 4: Securely mount the station to the wall using the
Zone 3 SW3/LD3 00LVS-04W
2.1
provided screws.
2.7 The terminals will accept 14-24 GA wire.
Zone 4 SW4/LD4
2.7
3.3
Step 5: Mount the wall plate to the station.
Zone 5 SW5/LD5
3.3
Zone 6 SW6/LD6
Zone 7 SW7/LD7
Zone 8 SW8/LD8
4
Zone 9 SW9/LD9 4
4
Zone 10 SW10/LD10
Step 1: If using a Decora Plus screwless wall plate, Step 2: Terminate the wiring to the appropriate termi-
remove the center tabs from the device as shown in
nals on your low voltage switch as is required for your
the following figure:
application. See the tables on page 5-7.
T e r m i n a l C o n n e c t i o n T y p e s
Step 3: When all wires have been terminated, gently
Depending on the needs of your equipment, the low volt-
Button Station age switch will support either closed circuit connection to
stuff the wires back into the junction box in the wall.
Label Terminal common, or closed circuit +V. The chart below lists the
options and requirements for the LD, LOC, and +24V/CM
Zone 1 SW1/LD1
terminals.
Wiring Wiring
Zone 2 SW2/LD2
Method #1 Method #2
Zone 3 SW3/LD3
+24VDC COMMON
Zone 4 SW4/LD4 Station
COMMON +24VDC Terminal
Zone 5 SW6/LD6
1
(00LVS-05W) 1
COMMON +24VDC
Zone 6 SW7/LD7
1
SW_
+24VDC COMMON
Zone 7 SW8/LD8
LD_

Terminal Connection Types

Zone 8 SW9/LD9
LOC
Zone 1 SW1/LD1
+24V/CM
Zone 2 SW2/LD2
Zone 3 SW3/LD3
The terminals will accept 14-24 GA wire.
Zone 4 SW4/LD4
Total # Button Station
Zone 5 SW5/LD5
Buttons Label Terminal
Total # Button Station
Buttons Label Terminal
Zone 6 SW6/LD6
1 On/Off SW3/LD3
1 On/Off SW3/LD3
Zone 7 SW7/LD7 ON
Zone 1 SW2/LD2
OFF
Zone 1 SW2/LD2
Zone 8 SW8/LD8 Wiring Wiring
2 Zone 2 SW4/LD4 +24V
8 9
Function Method #1 Method #2
2 Zone 2 SW4/LD4 PILOT
Zone 9 SW9/LD9
Zone 1 SW2/LD2
COMMON
Switch Output +24VDC COMMON
Zone 1 SW2/LD2
Zone 10 SW10/LD10
3
LOCATION
Zone 2 SW3/LD3
LED Input COMMON +24VDC
3
Zone 2 SW3/LD3
7
Zone 3 SW4/LD4
Locator COMMON +24VDC This page left intentionally blank. This page left intentionally blank.
Zone 3 SW4/LD4
Zone 1 SW2/LD2
Reference +24VDC COMMON
Zone 1 SW2/LD2
P r o g r a m m i n g / O p e r a t i o n
Zone 2 SW3/LD3
4
Zone 2 SW3/LD3
All System Programming, individual switch configuration,
Zone 3 SW4/LD4
4
and other device configuration options is performed at
Zone 3 SW4/LD4
Zone 4 SW5/LD5
the device to which your switch is connected.
Zone 4 SW5/LD5
5
5
5
I n t r o d u c t i o n
Description
I n t r o d u c t i o n
The Low Voltage Switches are a variant on the tradition-
The LV200 lighting controller is a Decora-style
al low voltage switch. They provide a switched momen-
The Low Voltage Switches are a variant on the tradition-
device for controlling non-dimmable and dimmable
tary contact which closes a low voltage circuit when the
al low voltage switch. They provide a switched momen-
luminaires connected to the miniZ Intelligent Daylight
switch is depressed and provides optional feedback to
tary contact which closes a low voltage circuit when the
the user through an LED contained within each button. Management System and Z-MAX Relay System. The
switch is depressed and provides optional feedback to
Additionally, each station has a rear illuminated "locator" LV200 provides a unique control station with multi-
the user through an LED contained within each button.
LED in the lower left hand corner. function operational and programming capabilities in a
Additionally, each station has a rear illuminated "locator"
LED in the lower left hand corner. 5-button configuration. The device come in white with
a matching wallplate.
LV200
Function description:
Push On - all lights to daylight harvesting level
Push Max - all lights to maximum trim level
W i r i n g a n d I n s t a l l a t i o n
Hold Bright - raise light levels with press hold or
Switches with
multiple press
Switches with
Zone 1
LED Indicator
Hold Dim - lower light levels with press hold or
Zone 1
LED Indicator
multiple press
Push Dim - lower light levels with press hold or
Zone 2
multiple press
Zone 2
Push Off - turn off lights
LED Locator
Programming capabilities:
LED Locator
Set daylighting target level
Set minimum lighting level
Wiring Wiring
Function Method #1 Method #2
Switch Output +24VDC COMMON
LED Input COMMON +24VDC

Wiring and Installation

Locator COMMON +24VDC
Total # Button Station
W i r i n g a n d I n s t a l l a t i o n
Part # Buttons Label Terminal
Total # Button Station
Reference +24VDC COMMON
Part # Buttons Label Terminal
Step 1: If using a Decora Plus screwless wall plate, Zone 1 SW1/LD1
remove the center tabs from the device as shown in
Zone 1 SW1/LD1
Zone 2 SW2/LD2
the following figure:
Zone 2 SW2/LD2
00LVS-05W 5
Zone 3 SW3/LD3
00LVS-05W 5
Zone 3 SW3/LD3
Zone 4 SW4/LD4
Zone 4 SW4/LD4
Zone 5 SW5/LD5
Zone 5 SW5/LD5
Zone 1 SW2/LD2
Zone 1 SW2/LD2
Zone 2 SW3/LD3
10 9
Zone 2 SW3/LD3
Zone 3 SW4/LD4
00LVS-06W 6
Zone 3 SW4/LD4
Zone 4 SW7/LD7
00LVS-06W 6
Zone 4 SW7/LD7
Zone 5 SW8/LD8 8
Zone 5 SW8/LD8
Zone 6 SW9/LD9
Zone 6 SW9/LD9
Step 2:
nals on
applica
W
Step 3:
Step 1: If
remove th
stuff the
the followi
2
2
This page
This page
6
6
6