AT&T SynJ SB67108 Quick Start Manual

Install and charge the handset battery
Step 1 Step 2
Align the cover flat
Plug the battery
connector securely against the battery
into the socket inside compartment, then
the handset battery slide it upwards.
compartment, matching
the color-coded label.
Insert the supplied
battery with the label
THIS SIDE UP facing up
as indicated.
Step 3
To lock the battery
compartment, turn
the latch clockwise
until it points to the
lock icon as shown
on the graphic.
Install and charge the handset battery
(continued)
To charge the handset, place it in the
Step 4
charger as shown. The CHARGE light
is on when the handset is charging.
CHARGE
light
Add and register handsets
You can add up to nine additional SynJ SB67108
handsets (sold separately) to the SynJ SB67118/
SB67138, but you must register each new
handset with the telephone base before use.
Additional handsets are assigned numbers in the
order they are registered (handsets 2 to 10).
To register a handset to your telephone base:
1. Make sure the handset is out of the charger
and the screen shows Press MENU on BS, sel
Registration & sel Register HS. Then put HS
in cradle before you begin registration.
2. On the telephone base, press MENU/ .
ENTER
3. Scroll down to Registration and press
ENTER.
MENU/
4. Press ENTER again to select Register HS.
MENU/
5. Place the unregistered handset into the
charger. The telephone base screen shows
Handset registering (SynJ SB67118 model)
or Registering new device... (SynJ SB67138
model). It takes up to 60 seconds to complete
the registration. You hear a beep when the
registration is successful. The handset shows
Add and register handsets (continued)
Handset registered, and then shows
X: Handset X (X represents the extension and
handset number).
NOTE: If the registration is not successful, the screen shows
Press MENU on BS, sel Registration & sel Register HS.
Then put HS in cradle. To reset the handset, remove the set the handset, remove the
handset from the charger. Try the registration process again.
Mailbox setup
Each handset has its own mailbox that is different
from the general mailbox on the base. If you turn
on the auto attendant on the base, the caller can
leave a message on the handset mailbox after
two rings (Fast answer mode = On), or five rings
(Fast answer mode = Off).
To turn Fast answer mode on or off:
1. Press the ress the M.box softkey.
2. Press DIR or CID to scroll to
Fast answer mode. Press /ENTER.
MENU
3. Press DIR or CID to select On or Off.
4. Press ENTER/ to save the setting and
MENU
return to the previous menu.
To record a new personal announcement:
1. Press the M.box softkey.
2. Press DIR or CID to scroll to
Anncemnt setup. Press /ENTER to play
MENU
current announcement.
3. Press the Press the Change softkey, and then press the
Start softkey. The system announces, "Record
after the tone. Press Stop when you are done."
4. Press the Stop softkey when finished. The
recorded announcement plays.
5. Press the OK softkey to use the new recorded
announcement.
-OR-
Press the Change softkey to record a new
announcement.
Message playback
You can play the messages from your handset
mailbox and the general mailbox. If you have
new messages, the system plays them (in
chronological order) automatically when you
access the mailbox.
To listen to new messages on a cordless handset: listen to new messages on a cordless handset:
When the handset is idle, press the M.box softkey.
To listen to new messages on the general
mailbox:
1. When the handset is idle, press the
M.box softkey.
2. Press DIR or CID to scroll to
General mailbox.
3. Press /ENTER.
MENU
Quick start guide
SynJ SB67108
DECT 6.0 expansion handset
for use with AT&T model
SynJ SB67118/SB67138