Quick Reference Instructions - Amana CRC21T2 Service Manual

Quick Reference Instructions

Read "Important Safety Information" before using "Quick
Reference Instructions". If there are unanswered questions,
see detailed sections of this manual.
Instructions are written for factory programmed ovens.
Ovens that are reprogrammed can respond differently
than described below.
Operating Preprogrammed Pads
1. Open oven door, place food in oven, and close oven
door.
2. Press MENU b/d pad to select preprogrammed menu.
3. Press desired number pad.
4. Oven stops heating and oven signal sounds when
heating time elapses.
Reviewing Preprogrammed Pads
1. Open oven door.
2. Press and hold TIME ENTRY pad for approximately 5
seconds.
3. Press MENU b/d pad to select preprogrammed menu
if necessary.
4. Press desired number pad.
5. Press TIME ENTRY pad to review heating stages for
pad.
6. Press START pad after reviewing preprogrammed pad.
7. Press RESET pad or close oven door to exit
programming mode.
Manual Time Entry
1. Open oven door, place food in oven, and close oven
door.
2. Press TIME ENTRY pad.
3. Press number pads to enter desired cooking time.
4. Press POWER LEVEL pad if power level other than
100 percent is required.
5. Press number pad to enter desired power level.
6. Press START pad.
7. Oven stops heating and oven signal sounds when
heating timing elapses.
Programming Number Pads
1. Open oven door.
2. Press and hold pad 1 for approximately 5 seconds.
3. Press MENU b/d pad to select preprogrammed menu
if necessary.
4. Press desired number pad.
5. Press number pads to enter desired cooking time.
6. Press POWER LEVEL pad if power level other than
100 percent is required.
7. Press number pad to enter desired power level.
8. Press START pad to save new heating time and
power level in oven memory.
9. Press RESET pad or close oven door to exit
programming mode.
RS2230003 Rev. 1
Programming Multiple Heating Stages
1. Open oven door.
2. Press pad 1 for approximately 5 seconds.
3. Press MENU b/d pad to select preprogrammed menu
if necessary.
4. Press desired number pad.
5. Press number pads to enter desired cooking time.
6. Press POWER LEVEL pad if power level other than
100 percent is required.
7. Press number pad to enter desired power level.
8. Press TIME ENTRY pad.
9. Press START pad to save new heating time and
power level in oven memory.
10. Press RESET pad or close oven door to exit
programming mode.
11. Repeat for 3 rd and 4
Deactivating Preprogrammed Pad
1. Open oven door.
2. Press and hold pad 1 for approximately 5 seconds.
3. Press desired number pad.
4. Press MENU b/d pad.
5. Press START pad to save in oven memory.
6. Press RESET pad or close oven door to exit
programming mode.
Reactivating Preprogrammed Pad
1. Open oven door.
2. Press and hold pad 1 for approximately 5 seconds.
3. Press desired number pad.
4. Press MENU b/d pad.
5. Program pad according to "Preprogrammed Number
Pads" section step 5-8.
6. Press START pad to save in oven memory.
7. Press RESET pad or close oven door to exit
programming mode.
Deactivating Control Panel
1. Open oven door, and close oven door.
2. Press TIME ENTRY pad.
3. Press 1,3,5, and 7 pad in sequence.
4. Press TIME ENTRY pad.
Reactivating Control Panel
• Reactivate control panel by repeating steps 1-4 of
"Deactivating Control Panel".
User Options
1. Open oven door. Display shows
"MENU b OR d – READY".
2. Press and hold pad 1 for approximately 5 seconds.
3. Press POWER LEVEL pad.
4. Press START pad to advance to next option. See
table for options.
5. Press number pad (0,1-3) to change option.
6. Press START pad to save changes.
7. Press RESET pad or close oven door to exit
programming mode.
14
th stages.