Advertisement
Quick Links
X50V3L Series Quick Guide【English】
.
E
Front/Rear/Side View
01
02
03
04
05
06
07
08
08
Stand / Handle
01
Microphone
02
Webcam
03
LCD Display (Single Touch / Non Touch)(Optional)
04
WiFi LED
05
Hard disk drive LED
06
Power LED
07
08
Stereo speakers
E
Placing on the desk
To place the machine on the desk and to carry it, do the following:
Place the X50V3L on a flat surface such as a table (Picture 1), and pull the stand
upwards to an angle of 30° (Picture 2). To carry or move your X50V3L fully extend
the angle to 180° (Picture 3).
1.
2.
30
E
Powering on the system
Follow the steps (1~3) below to connect the AC adapter to the DCIN jack.
Press the Power Button to turn on the system.
E
Cleaning the screen
Follow these guidelines for cleaning the outside and handling the screen of the computer:
Turn off the system and disconnect all cables.
Use a damp, or cleaning cloth, soft, lint-free cloth with gentle water only and gently
wipe the screen surface.
Do not spray liquid directly on the screen.
Note: The product's color and specification will depend upon the actually shipping product.
09
10
17
18
19
11
20
12
21
13
14
22
15
16
Power Button
HDMI Port
17
09
Stylus pen
USB 2.0 Ports
10
18
SD card reader
11
VGA Port
19
Microphone Jack
Power Input
12
20
Headphone / Line-out Jack
Printer Port (Optional)
13
21
LAN Port
COM Ports (Optional)
14
22
15
USB 2.0 Ports
Kensington® Lock Port
23
Stand / Handle
16
E
How to use the Touch Panel (Optional)
X50V3L brings digital life for an easy touch experience.Experience the ease of
managing your digital life with a few touches or the use of the stylus pen. The
touch of your finger replaces the mouse and is all you need to interact with the
X50V3L .
・
Touch = left-click on the mouse
3.
・
Touch and hold = right-click on the mouse
180
E
VESA mounting it to the wall
If you are mounting your X50V3L to the wall, remove the cover on the back of
X50V3L first.
Unscrew 4 screws of the stand mount and remove the stand.
The VESA standard lets users mount it on to walls easily.
Please refer to the user guide of the wall/arm mount kit you bought to install it.
Note : X50V3L can be mounted to a wall using a VESA compatible
100 x 100mm wall/arm bracket.
E
4 Point Calibration (Optional)
Run the screen calibration
program and correct 4 point
locations on screen with the
panel.
Click Start / All Programs
/ eGalax Touch
/ Configure Utility
Select [Tools] tab and click
[4 Points Calibration]
23
E
Safety Information
DCIN
Read the following precautions before setting up a Shuttle X50V3L .
CAUTION
Do not walk on the power cord or allow anything to rest on it.
The warranty does not apply to the products that have been disassembled by users.
CAUTION
Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions.
A. Begin Installation
For safety reasons, please ensure that the power
cord is disconnected before opening the case.
1. Remove the cover on the back of X50V3L first, unscrew
four screws of the stand mount and remove the stand.
Cover
2. Unscrew four screws of the back cover and remove it.
B. HDD Installation
1. Unscrew four screws of the VESA Base and remove it first.
Touch and hold the center of the target.
Repeat on four corners and the screen will adjust automatically.
When the 4 points calibration completed, press [OK] to continue.
2. Unscrew three screws of the bracket and remove it.
3. Mount HDD into the bracket with four screws.
Screw
4. As shown, install the HDD & bracket in the chassis and
push it towards the direction as indicated by the red arrow
to connect the HDD connector.
5. Tighten the HDD & bracket with three screws.
Stand / Handle
HDD
Connector
C. Memory Module Installation
If you install only one memory module in your
system, install it in the slot labeled "DIMM2".
1. Locate the SODIMM slot on the mainboard.
2. Align the notch of the
SODIMM slot
memory module with
the one of the memory
slot.
Screw
3. Gently insert the
VESA Base
module into the slot
1
in a 45-degree angle.
2
45-degree
angle
Touch
Hold
OK
4. Carefully push down the memory module until it snaps into
the locking mechanism.
5. Repeat the above steps to install additional memory modules,
if required.
Latch
Latch
DIMM2
DIMM1
6. Replace the VESA Base and refasten four screws.
Screw
VESA Base
D. Complete
1. Replace the back cover, stand and refasten eight screws.
Back Cover
Stand / Handle
Screw
2. Replace the cover, complete.
53R-X50V33-2501
Advertisement
