Advertisement
Quick Links
X70 Series Quick Guide 【 English 】
.
E
Front/Rear/Side View
02
01
03
16
17
04
05
18
06
07
08
10
11
12
14
09
13
Webcam
Power LED
01
05
Microphone
Stereo speakers
02
06
LCD Display (Optional)
Microphone Jack
03
07
(Single/Multi/Non Touch)
Headphone / Line-out Jack
08
Hard Disk Drive LED
Lan Ports
04
09
E
Placing on the desk
To place the machine on the desk and to carry it, do the following:
Place the X70 on a flat surface such as a table (Picture 1), and pull the stand
upwards to an angle of 30°, the support bracket can be opened to 60 degrees at
most(Picture 2). To carry or move your X70, turn back the angle to 0° (Picture 3).
1.
2.
Max 60
E
Powering on the system
Follow the steps (1~3) below to connect the AC adapter to the DC in jack.
Press the Power Button to turn on the system.
DCIN
E
Cleaning the screen
Follow these guidelines for cleaning the outside and handling the screen
of the computer:
Turn off the system and disconnect all cables.
Use a damp, or cleaning cloth, soft, lint-free cloth with gentle water only
and gently wipe the screen surface.
Do not spray liquid directly on the screen.
Note: The product's color and specification will depend upon the actually shipping product.
20
22
21
19
15
USB 3.0 Port
COM Port
10
15
20
HDMI Port
Printer Port (Optional)
11
16
21
USB 2.0 Ports
COM Ports (Optional)
12
17
22
Clear CMOS Button
13
18
Stand / Handle
23
DC in
Kensington® Lock Port
14
19
24
E
How to use the Touch Panel (Optional)
X70 brings digital life for an easy touch experience.Experience
the ease of managing your digital life with a few touches.
The touch of your finger replaces the mouse and is all you need
to interact with the X70.
・
Touch = left-click on the mouse
・
Touch and hold = right-click on the mouse
3.
E
VESA mounting it to the wall
Power
Button
4
If you are mounting your X70 to the wall, remove the cover
on the back of X70 first.
Unscrew three screws of the stand mount and remove the
stand.
The VESA standard lets users mount it on to walls easily.
Please refer to the user guide of the wall/arm mount kit you
bought to install it.
Note : X70 can be mounted to a wall using a VESA
compatible 100 x 100mm wall/arm bracket.
E
4 Point Calibration (Optional)
Run the screen calibration
program and correct 4 point
locations on screen with the
panel.
Click Start / All Programs
/ eGalax Touch
/ Configure Utility
Select [Tools] tab and click
[4 Points Calibration]
24
23
E
Safety Information
Read the following precautions before setting up a Shuttle X70.
CAUTION 1.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions.
Thermal Vent
A. Begin Installation
Power Button
USB 2.0 Ports
For safety reasons, please ensure that the power
USB 2.0 Ports
cord is disconnected before opening the case.
SD Card Reader
1. Remove the cover on the back of X70 first, unscrew
three screws of the stand mount and remove the stand.
Cover
Screw
Stand / Handle
2.
Unscrew four screws of the back cover and remove it.
B. ICE and CPU Installation
1. Unscrew the four screws of the VESA Base and remove
it first.
2. Unscrew the four screws of the the fans and unplug the
fan connectors(Step 1), then unfasten the four ICE
module attachment screws(Step 2).
Step 1
Fan
Fan
ICE
module
Step 2
Touch and hold the center of the target.
Repeat on four corners and the screen will
adjust automatically.
When the 4 points calibration completed,
press [OK] to continue.
CAUTION 2.
Do not walk on the power cord or allow anything to rest on it.
The warranty does not apply to the products that have been disassembled by users.
3. Remove the fans and ICE module from the chassis
8. Spread thermal paste evenly on the CPU surface.
and put them aside.
Please note this 1155 pin socket bends easily.
Always apply extreme care and little force when
installing a CPU and limit the number of times you
remove or exchange it. Before installation, make
Metal load
plate
sure to turn off the computer and unplug the power
cord from the mains to avoid damage.
Retention
tab
Follow the steps below to correctly install the CPU into the
motherboard CPU socket.
Please do not apply excess amount of thermal paste.
4. First unlock and raise the socket lever.
9. Screw the ICE module to the mainboard. Note to press
down on the opposite diagonal corner while tightening
each screw.
10. Fasten the fans with the four screws and connect the
fan connectors.
C. Memory Module Installation
1. Locate the SODIMM slot on the mainboard.
5. Lift the metal load plate on the CPU socket. Tear
2. Align the notch of the memory module with the one
of the memory slot.
off the protective membrane from the bottom of ICE
module. Remove the protective socket mylar from the
CPU socket.
Metal
load plate
Remove the
protective
membrane
3. Gently insert the module into the slot in a 45-degree
angle.
DO NOT touch socket contacts. To protect the
CPU socket, always replace the protective socket
cover when the CPU is not installed.
2
6. Orientate the CPU and socket and please align the
45-degree
angle
CPU notches with the socket alignment keys. Make
sure the CPU is perfectly horizontal, insert it into the
socket.
4. Carefully push down the memory module until it
snaps into the locking mechanism.
Triangle
Pin1
5. Repeat the above steps to install additional memory
Marking
modules, if required.
on the
CPU
Socket
1155
Notch on
CPU
the CPU/
Alignment
Key of the
CPU Socket
6. Replace the VESA Base and refasten four screws.
Please be aware of the CPU orientation, DO NOT
force the CPU into the socket to avoid bending of
D. HDD Installation
pins on the socket and damage of CPU!
1. Unscrew the screw of the bracket and remove it.
7. Close the metal load plate, lower the CPU socket lever
2. Mount HDD into the bracket with four screws.
and lock in place.
62R-X70000-0601
X70
English.Spanish.Korean.
Traditional Chinese.Japanese.
French. German Quick Guide
Touch
Hold
OK
Thermal
Paste
application
area
3. As shown, install the HDD & bracket in the chassis
and push it towards the direction as indicated by the red
arrow.
Load lever
4. Tighten the HDD & bracket with one screw.
HDD
5. Connect the Serial ATA and power cables to the HDD.
SODIMM slot
Serial ATA
Cable
Serial ATA
Power Cable
E. Complete
1
1. Replace the back cover, stand and refasten seven
screws.
Screw
Stand / Handle
Back Cover
2. Replace the cover, complete.
53R-X70003-2001
Advertisement
