Pioneer XDJ-R1 Operating Instructions Manual page 36

Functions and operations
Problem
Can't crossfade.
Back cue function does not work.
Beat effect does not work.
Color effect does not work.
[SYNC] function does not work.
[SYNC] function does not work even
when files are analyzed.
Settings are not stored in the
memory.
USB devices
Problem
USB device is not recognized.
Time is required to read USB devices
(flash memory drives and hard discs).
Playback does not start when a track
is loaded from a USB device.
File cannot be played.
Music files cannot be played.
DJ software
Problem
DJ software on a computer cannot be
operated.
DJ software's sound is not properly
output.
Sound being played is interrupted
when using DJ software.
36
En
Check
Is the [CROSS F. CURVE (THRU,
fader curve selector) switch set to [THRU]?
Is a cue point set?
Is one of the [BEAT FX] buttons (TRANS, FLANGER,
ECHO or ROLL) pressed?
Is the [LEVEL/DEPTH] control set to the center
position?
Is the [BEAT] control set to the proper position?
Is a
[SOUND COLOR FX (NOISE, PITCH, CRUSH, FILTER)]
button pressed?
Is the [COLOR] control set to the proper position?
Has the music file been analyzed?
Is the beat grid irregular?
Is the beat grid properly tapped?
Are the BPMs of the tracks in the two decks too
different?
Are you scratching?
Has the power been turned off directly after chang-
ing the setting?
Check
Is the USB device properly connected?
Is the USB device connected via a USB hub?
Is the USB device supported by this unit?
Is the file format supported by this unit?
Are you using a USB device (such as a bus power-
driven hard disk) whose current is higher than this
unit's rated current (500 mA)?
—
Is there a large number of folders or files recorded
on the USB device?
Are files other than music files stored on the USB
device?
Are the files playable?
Is the auto cue function activated?
Is the file copyright-protected (by DRM)?
Are the music files damaged?
Check
Is the included USB cable properly connected?
Are the DJ software's output settings and this
unit's [MIXER MODE] setting properly set?
Is the driver software properly set?
Are the connection cables properly connected?
Are terminals or plugs dirty?
Is the connected, power amplifier, powered speak-
ers, etc., properly set?
Is the driver software's latency value suitable?
Remedy
, )] (cross- Set the [CROSS F. CURVE (THRU,
to a position other than [THRU]. (Page 22)
Set a cue point. (page 15)
Press one of the [BEAT FX] buttons (TRANS, FLANGER, ECHO or ROLL). (page
20)
Turn the [LEVEL/DEPTH] control clockwise or counterclockwise. (page 20)
Set the [BEAT] control to the proper position. (page 20)
Press one of the [SOUND COLOR FX (NOISE, PITCH, CRUSH, FILTER)] buttons.
(page 20)
Set the [COLOR] control to the proper position. (page 20)
Analyze the file. (page 23)
Set the beat grid properly. (page 23)
The [SYNC] function will not work properly if the BPM of the track on the deck
for which the [SYNC] button is pressed is outside the adjustable tempo range of
the track on the deck for which the [SYNC] button is not pressed.
The [SYNC] function is disabled when scratching.
After changing settings, wait at least 10 seconds before turning the power off.
After editing (recording or deleting) a sampled sound source, be sure to press
the [STANDBY/ON] button to turn the power off.
Remedy
Connect the device securely (all the way in).
USB hubs cannot be used.
This unit supports such USB mass storage class USB devices as external hard
disks and portable flash memory devices.
Check the file format of the connected USB device. For the file formats sup-
ported by this unit, see About USB devices on page 5.
Use a USB device within this unit's rated current (such as a hard disk driven by
an AC adapter or other external power supply).
Turn the power off, wait 1 minute, then turn the power back on.
When there are many folders or files, some time may be required for loading.
When files other than music files are stored in folders, time is required to read
them as well. Do not store files or folders other than music files on the USB
device.
See Playable music file formats on page 5.
Press the [TIME(AUTO CUE, QUANTIZE)] button for over 1 second to cancel the
auto cue function. (page 18)
Copyright-protected files cannot be played.
Play music files that are not damaged.
Remedy
Connect the computer and this unit directly using the included USB cable. USB
hubs cannot be used. (page 10)
Check the DJ software's settings, then check this unit's settings on the
[UTILITY] screen and set the proper signal path. (page 27)
Set the driver software properly. (Page 26)
Connect the connection cables properly. (page 10)
Wipe any dirt off terminals and plugs before connecting.
Properly set the external input selection, volume, etc., on the power amplifier,
powered speakers, etc.
Set the driver software's latency to a suitable value. (Page 26)
Set the DJ software's latency to a suitable value.
, )] (crossfader curve selector) switch