UNSAFE Vehicle Belt Systems ....14 Assembling the Booster Seat ....15-16 Assembling the Back Support ....17-22 Using your Graco Booster Seat ....23-25 Booster Seat Positions ........26 Attaching Booster to Vehicle Seat ..... 27-29 Securing your Child in Vehicle .....30-33 Adjusting the Head Support ......
You must register this restraint to be reached in a recall. Send your name, address, and the restraint s model number and date of manufacture to: Graco Children s Products Inc. Attn: Customer Service 3 Glenlake Parkway Atlanta, GA 30328...
STOP using this booster seat and throw it away 10 years after the date of manufacture. Look for this sticker on the bottom of the booster seat: MODEL NAME Date of Manufacture year month GRACO CHILDREN'S PRODUCTS, INC. ATLANTA, GA 30328 1-800-345-4109 Made in China...
Parts List Adult assembly required. Shoulder belt positioning clip Base Cupholder (in bottom of base) Armrests On certain models Lower back support Head support Seat pad Seat pad...
Warnings to Parents and Other Users NEVER PLACE THIS BOOSTER SEAT IN A VEHICLE SEATING LOCATION THAT HAS AN AIR BAG. If an air bag inflates, it can hit the child and booster seat with great force and cause serious injury or death to your child.
Page 7
NO BOOSTER SEAT CAN GUARANTEE PROTECTION FROM INJURY. HOWEVER, PROPER USE OF THIS BOOSTER SEAT REDUCES THE RISK OF SERIOUS INJURY OR DEATH TO YOUR CHILD. DO NOT INSTALL OR USE THIS BOOSTER SEAT UNTIL YOU READ AND UNDERSTAND THE INSTRUCTIONS IN THIS MANUAL AND IN YOUR VEHICLE OWNER’S MANUAL.
Page 8
According to crash statistics, CHILDREN ARE SAFER WHEN PROPERLY RESTRAINED IN REAR VEHICLE SEATING POSITIONS, RATHER THAN FRONT SEATING POSITIONS. For a vehicle with a front passenger air bag, refer to your vehicle owner s manual as well as these instructions for booster seat installation.
Page 9
DO NOT MODIFY YOUR BOOSTER SEAT or use any accessories or parts supplied by other manufacturers. NEVER USE BOOSTER SEAT IF IT HAS DAMAGED OR MISSING PARTS. DO NOT use a cut, frayed or damaged vehicle seat belt. THE BOOSTER SEAT CAN BECOME VERY HOT IF LEFT IN THE SUN.
FAILURE TO USE booster seat in a manner appropriate for your child s si e may increase the risk of serious injury or death. To use this Graco booster seat, your child MUST meet ALL of the following requirements: With back support (approximately 3 to 10 years old) : weigh between 30 and 100 lbs.
If you are not sure where to place the booster seat in your vehicle, consult your vehicle owner s manual or call Graco Children s Products Inc., at 1-800-345-4109. Children are safer when properly restrained in rear vehicle seating positions.
NOT safe to use look very much like seat belts that are safe to use. If you are unsure, consult your vehicle owner s manual or call Graco Children s Products Inc., at 1-800-345-4109. SAFE...
UNSAFE Vehicle Seat Belt Systems DO NOT USE ANY OF THE FOLLOWING VEHICLE BELT SYSTEMS. NEVER use a lap-only belt. NEVER use a Passive Restraint - Lap or Shoulder Belt Mounted on Door NEVER use a Passive Restraint - Lap Belt with Motori ed Shoulder Belt NEVER use vehicle belts that are attached to...
Assembling the Booster Seat Step 1. To attach armrests to base, press armrests into SNAP! opening in base CHECK to make sure armrests are securely attached by pulling up on them Step 2. Remove cupholder from compartment in bottom of base .
Page 16
Step 3. Wrap seat pad around front of base attach with elastic straps as shown. Step 4. Your Graco booster seat is now ready to use. See page 27, “Attaching Booster to Vehicle Seat”. FOR MODELS with a back support continue...
Assembling the Back Support (on certain models) Step 5. On certain models, your lower back support pad may not be attached to the back support. Place lower back support pad around edges of support as shown. Then fasten lower elastic strap to the metal hook on the other side of the seat pad.
Page 18
Step 6. Squee e red adjustment button and slide two pieces together until they snap into place CHECK to make sure two pieces are securely snapped together by pulling on them. SNAP! Step 7. Attach elastic strap to metal hook on other side of seat pad as shown .
Page 19
Step 8. Flip seat over and insert the fabric from the head support underneath the fabric on the lower back support as shown To make insertion of fabric easier, slide the upper and lower back pieces apart by squee ing the red adjustment button.
Page 20
Step 9. Attach backrest to base. “U”-shaped hooks on bottom of backrest will interlock with bars on base Make sure that no part of the seat covering interferes when attaching backrest to the base.
Page 21
Step 10. Once backrest is securely attached to the base, push backrest up as shown...
Page 22
Step 11. Your Graco booster seat is now ready to use. See page 23-35.
Using your Graco Booster Seat FAILURE TO PROPERLY SECURE YOUR CHILD AND THE BOOSTER SEAT IN YOUR VEHICLE INCREASES THE RISK OF SERIOUS INJURY OR DEATH IN THE EVENT OF A SHARP TURN, SUDDEN STOP OR CRASH. WARNING: Use only...
Page 24
Vehicle belts MUST lie flat against child and MUST not be twisted. DO NOT use shoulder belt loose or positioned under child s arm DO NOT position vehicle belt over top of the armrests . It must pass underneath the armrests. Make sure vehicle belt is NOT twisted.
Page 25
Vehicle seat headrest must not interfere with booster seat head support. The front of booster seat MUST NOT hang over front of vehicle seat The back of the booster seat MUST fit tight against the vehicle seat back as shown...
Booster Seat Positions Your booster seat has two positions as shown. Upright Reclined The back of the booster seat MUST fit tight against the vehicle seat back as shown in either the first or second position. DO NOT USE booster seat beyond reclined position...
Attaching Booster to Vehicle Seat WARNING: Use only the vehicle s lap and shoulder belt system when restraining the child in this booster seat. AFFIX connectors are ONLY to secure the booster seat to the vehicle seat. When using the AFFIX connectors, DO NOT place booster...
Page 28
1. Push button on front of seat and pull connectors out from back of booster 2. Attach connectors to vehicle lower anchors Pull firmly on connectors be sure they are attached. NEVER put two connectors on one vehicle anchor...
Page 29
3. Tighten connectors, by pushing on booster and pulling straps on front of booster 4. To remove booster, push release button up on front of booster and pull slightly away from seat. 5. Push connector in , lift connector up and pull out (away from anchor point) Repeat on other...
Securing Your Child in Vehicle 1. Place booster seat firmly against the back of a forward-facing vehicle seat equipped with a lap/ shoulder belt only 2. Have your child sit in booster seat with their back flat against back of booster seat.
Page 31
3. Position shoulder belt through the shoulder belt guide shown in , NOT as shown in . Fasten buckle and pull up on the shoulder belt to tighten. CORRECT INCORRECT...
Page 32
4. To ensure the correct head support height is obtained, the bottom of the headrest SHOULD be even with the top of child s shoulders as shown in and the shoulder belt must be positioned in the red CORRECT one as shown in The lap belt portion MUST pass under the armrests and be...
Page 33
5. If the belt lies across child s neck, head or face , readjust head support height. Follow instructions on page 34, “Adjusting the Head Support”. INCORRECT INCORRECT INCORRECT...
Adjusting the Head Support BEFORE adjusting the head support height, have your child lean forward slightly. Squee e the red adjustment button on top of seat and pull back support up until it snaps into one of the 6 height Back of seat positions.
Removing the Back Support (on certain models) to Use as Backless Booster To use booster seat without back support: Remove back support as shown. “U”-shaped hooks on bottom of back support are interlocked with bars on base. Lift back support off base.
Securing Child in Vehicle with Shoulder Belt Positioning Clip The shoulder belt MUST lie across child s shoulders in red one as shown. If shoulder belt lies outside this one, the shoulder belt positioning clip MUST be used. To attach clip to booster seat: 1.
Page 37
2. Pass the clip and strap through the loop end as shown and pull strap up NOTE: Free end of strap should face front of seat.
Page 38
3. Slide the vehicle shoulder belt onto the clip as shown in and pull strap down to tighten clip against child s shoulder. The lap belt portion MUST pass under the armrests and be positioned low on the hips. The belt MUST NOT be twisted. Shoulder belt positioning clip...
Page 39
Rear view of child sitting in seat Shoulder belt positioning clip 4. For warnings on vehicle belt positions, see page 23-25, “Using your Graco Booster Seat”.
Additional Information Airplane Use This restraint is NOT certified for aircraft use because there are no shoulder belts available in an aircraft. Cupholder and Storage Compartment Cupholder and storage compartment are included on sides of the seat.
Instruction Sheet Storage Your instruction sheet can stored on the bottom of the seat as shown. Care and Maintenance CONTINUOUS USE OF BOOSTER SEAT MAY CAUSE DAMAGE TO VEHICLE SEAT. Use a booster seat mat, towel or thin blanket to protect upholstery.
To Remove Seat Cover 1. Remove elastic loops and hooks from seat as shown Refer to your care tag on your seat pad for washing instructions. NO BLEACH. 3. To put the seat cover back on, re-attach pad, loops and hooks.
Replacement Parts To purchase parts or accessories or for warranty information in the United States, please contact us at the following: www.gracobaby.com 1-800-345-4109...
Envíe su nombre, dirección y número de modelo y fecha de fabricación a: Graco Children's Products Inc. Attn: Customer Service 3 Glenlake Parkway Atlanta, GA 30328 EE.UU.
10 años después de la fecha de fabricación. Busque la etiqueta en el lado inferior del asiento de seguridad: MODEL NAME Date of Manufacture year month GRACO CHILDREN'S PRODUCTS, INC. ATLANTA, GA 30328 1-800-345-4109 Made in China...
Lista de piezas Se requiere el montaje por un adulto. Clip de colocación del cinturón de hombro Base Apoyavaso (abajo de la base) Apoyabrazos En ciertos modelos Respaldo Apoyacabezas Almohadilla del asiento Almohadilla del asiento...
Advertencias a padres y otros usuarios NUNCA COLOQUE ESTA ASIENTO PARA NIÑOS EN UN ASIENTO DEL VEHÍCULO EQUIPADO CON BOLSA DE AIRE. Si la bolsa de aire se infla, puede golpear al niño y a el asiento para niños con mucha fuerza y puede causar lesiones graves o la muerte de su niño.
Page 51
NINGÚN ASIENTO DE SEGURIDAD PARA AUTOMÓVIL PUEDE GARANTIZAR LA PROTECCIÓN CONTRA LESIONES EN TODAS LAS SITUACIONES. SIN EMBARGO, EL USO CORRECTO DE ESTE ASIENTO DE SEGURIDAD PARA AUTOMÓVIL REDUCE EL RIESGO DE QUE SU NIÑO SUFRA LESIONES SERIAS O LA MUERTE. NO INSTALE NI USE ESTE ASIENTO PARA NIÑOS ANTES DE LEER Y ENTENDER LAS INSTRUCCIONES EN ESTE MANUAL Y EN...
Page 52
Según las estadísticas de accidentes, LOS NIÑOS ESTÁN MÁS SEGUROS CUANDO SE ENCUENTRAN SUJETADOS CORRECTAMENTE EN LOS ASIENTOS TRASEROS DE LOS VEHÍCULOS, EN VEZ DE LOS ASIENTOS DELANTEROS. Para vehículos con bolsas de aires para los pasajeros delanteros, refiérase al manual del propietario de su vehículo, además de estas instrucciones para la instalación del asiento para niños.
Page 53
NO MODIFIQUE SU ASIENTO PARA NIÑOS ni use ningún accesorio o pieza proporcionados por otros fabricantes. NUNCA USE UN ASIENTO PARA NIÑOS QUE TENGA PIEZAS DAÑADAS O FALTANTES. NO use un cinturón de seguridad cortado, desgastado o dañado. EL ASIENTO PARA NIÑOS PUEDE CALENTARSE MUCHO SI SE DEJA AL SOL.
Para usar este asiento para niños de Graco, su niño DEBE cumplir con TODOS los requisitos siguientes: Con respaldo (de 3 a 10 años, aproximadamente): o debe pesar entre 30 y 100 libras (13.6 y 45 kg), y...
Page 55
/ apoyacabezas del asiento del vehículo. Su asiento para niños de Graco puede usarse con o sin el respaldo (en ciertos modelos) siempre y cuando se cumplan los requisitos anteriores.
Cuando sea posible, sujete el asiento para niños de Graco en la posición central del asiento directamente detrás de los asientos delanteros. Sin embargo, a menudo, esta posición viene equipada solamente con un cinturón de regazo y en dicho caso, no se puede usar.
NO son seguros para usar se parecen mucho a los que sí son seguros. Si no está seguro, consulte el manual del propietario de su vehículo o llame a Graco Children's Products Inc. al 1-800-345-4109. Sistemas...
Sistemas INSEGUROS de cinturones de seguridad del vehículo NO USE NINGUNO DE LOS SIGUIENTES SISTEMAS PARA SUJETAR EL ASIENTO DE SEGURIDAD. NUNCA use un cinturón de regazo solamente. NUNCA use un cinturón pasivo - un cinturón de regazo u hombro montado en la puerta NUNCA use un cinturón pasivo - un...
Montar del asiento para niños Paso 1. Para sujetar los CLIC! ¡ apoyabrazos a la base, oprímalos en la abertura de la base VERIFIQUE que los apoyabrazos están bien conectados, jalando los mismos Paso 2. Saque el apoyavasos del compartimiento de abajo .
Page 60
Paso 4. Su asiento para niños de Graco ya está lista para usar. Vea la página 27, “Cómo sujetar el asiento para niños al asiento del vehículo”. PARA LOS MODELOS con respaldo, siga con el Paso 5.
Montar el respaldo (en ciertos modelos) Paso 5. En ciertos modelos, es posible que la almohadilla inferior del respaldo no esté sujeta al respaldo. Coloque la almohadilla inferior del respaldo alrededor de los bordes de apoyo, como indica la figura. Luego ajuste la correa elástica inferior al gancho de metal que está...
Page 62
Paso 6. Apriete el botón rojo de ajuste y junte las dos piezas hasta que encajen en su sitio VERIFIQUE que las dos piezas estén bien conectadas, jalando las mismas. ¡CLIC! Paso 7. Sujete la correa de elastica como se indica Si ya sujetó...
Page 63
Paso 8. De la vuelta al asiento e inserte la tela del apoyacabezas debajo de la tela del respaldo como se indica Para facilitar la inserción de la tela, separe las piezas superior e inferior del respaldo, apretando el botón rojo de ajuste.
Page 64
Paso 9. Conecte el respaldo a la base. Los ganchos en forma de "U" en el fondo del respaldo se engancharán en las barras de la base Asegúrese que ninguna pieza de la funda del asiento interfiera con la conexión del respaldo a la base.
Page 65
Paso 10. Una vez que el respaldo está bien conectado a la base, suba el mismo como se indica...
Page 66
Paso 11. Su asiento para niños de Graco ya está lista para usar. Vea las páginas 23 a 35.
Usar su asiento para niños de Graco NO SUJETAR CORRECTAMENTE A SU NIÑO Y EL ASIENTO PARA NIÑOS EN SU VEHÍCULO AUMENTA EL RIESGO DE LESIONES GRAVES O LA MUERTE EN CASO DE UN GIRO BRUSCO, UNA PARADA REPENTINA O UN ACCIDENTE.
Page 68
Los cinturones del vehículo DEBEN quedar planos encima del niño y NO DEBEN quedar torcidos. NO use el cinturón de los hombros suelto debajo del brazo del niño NO coloque el cinturón del vehículo por encima de los apoyabrazos Debe pasar por debajo de los apoyabrazos.
Page 69
NO permita que el niño se deslice hacia abajo en el asiento para niños Si el niño no mantiene la posición correcta del cinturón de seguridad del vehículo, NO use este asiento para niños. Use otro sistema de seguridad infantil. El apoyacabezas del asiento del vehículo no debe interferir con el...
Posiciones del asiento para niños Su asiento para niños tiene dos posiciones como se indica. Vertical Reclinado El respaldo del asiento para niños DEBE caber ajustadamente contra el respaldo del asiento del vehículo como se indica en la primera o segunda posición.
Cómo sujetar el asiento para niños al asiento del vehículo ADVERTENCIA: Use solamente el sistema de cinturón para la falda y el hombro del vehículo cuando sujeta a su niño en este asiento para niños. Los conectores AFFIX son SOLAMENTE para sujetar el asiento para niños al asiento del vehículo.
Page 72
1. Oprima el botón de adelante del asiento y tire los conectores hacia afuera desde atrás del asiento para niños 2. Sujete los conectores a los anclajes inferiores del vehículo Tire firmemente de los conectores para asegurarse de que estén enganchados.
Page 73
3. Ajuste los conectores, empujando el asiento para niños y tirando las correas de adelante 4. Para sacar el asiento para niños, empuje el botón de liberación hacia arriba en la parte de adelante del asiento para niños y tírelo apenas hacia afuera del asiento.
Sujetar a su niño en el vehículo 1. Coloque el asiento para niños firmemente contra el respaldo de un asiento del vehículo orientado hacia delante solamente con un cinturón de regazo / hombro 2. Siente a su niño en el asiento para niños con su espalda plana contra el respaldo del asiento para niños.
Page 75
3. Pase el cinturón de hombro por el soporte del cinturón de hombro como se indica en NO como se indica en . Abroche la hebilla y jale el cinturón de hombro hacia arriba para ajustarlo. CORRECTA INCORRECTA...
Page 76
4. Para asegurar que obtiene la altura correcta para apoyar la cabeza, la parte de abajo del apoyacabeza DEBE estar parejo con la parte de arriba de los hombros del niño como se indica en CORRECTA y el cinturón de hombro debe estar colocado en la zona roja como se indica...
Page 77
5. Si el cinturón pasa a través del cuello, la cabeza o la cara del niño , vuelva a ajustar la altura del apoyacabezas. Cumpla las instrucciones en la página 34, “Ajustar el apoyacabezas”. INCORRECTA INCORRECTA INCORRECTA...
Ajustar el apoyacabezas ANTES de ajustar la altura del apoyacabezas, incline a su niño un poco hacia delante. Apriete el botón rojo de ajuste en la parte superior del asiento y jale el apoyacabezas hacia arriba hasta que encaje en una de Parte trasera del asiento las 6 posiciones de altura.
Desmontar el respaldo (en ciertos modelos) para usarlo como asiento para niños sin respaldo Para usar la asiento para niños sin respaldo: Desmonte el respaldo como se indica. Los ganchos en forma de "U" en el fondo del respaldo están entrelazados con las barras de la base.
Sujetar a su niño en el vehículo con el clip de colocación del cinturón de hombro El cinturón de hombro DEBE pasar por encima de los hombros del niño en la zona roja como se indica. Si el cinturón de hombro queda fuera de esta zona, se DEBE usar el clip de colocación del cinturón de hombro.
Page 81
2. Pase el clip y la correa por el extremo con el bucle como se indica en y jale la correa hacia arriba NOTA: El extremo libre de la correa debe quedar orientado hacia la parte delantera del asiento.
Page 82
3. Deslice el cinturón de hombro del vehículo en el clip como se indica en y jale la correa hacia abajo para ajustar el clip contra el hombro del niño. El cinturon de regazo DEBE pasar debajo del apoyabrazos y queda en la parte inferior de las caderas del niño.
Page 83
Plano trasero del niño sentado en el asiento Clip de colocación del cinturón de hombro 4. Para advertencias sobre las posiciones del cinturón de seguridad del vehículo, vea las páginas 23 a 25, "Usar su asiento para niños de Graco".
Información adicional Uso en aviones Este asiento de seguridad no está certificado para su utilización en aviones, ya que éstos no disponen de cinturones de hombros. Apoyavasos y compartimiento de almacenamiento El apoyavasos y compartimiento de almacenamiento se incluyen en los costados del asiento.
Almacenaje de la hoja de instrucciones Se puede guardar su hoja de instrucciones en el fondo del asiento como se indica. Cuidado y mantenimiento EL USO CONTINUO DEL ASIENTO PARA NIÑOS PODRÁ CAUSAR DAÑOS AL ASIENTO DEL VEHÍCULO. Use una almohadilla para asientos para niños, una toalla o una manta fina para proteger el tapizado.
Page 86
Para quitar la funda del asiento 1. Quite los bucles elásticos y los ganchos del asiento, como se indica 2. Lave la funda en agua fría en el ciclo delicado y déjela secar al aire. NO USE CLORO. 3. Para volver a colocar la funda, siga las instrucciones anteriores en orden inverso.
Repuestos Para comprar piezas o accesorios o para obtener información sobre la garantía en los Estados Unidos, por favor comuníquese con nosotros en: www.gracobaby.com 1-800-345-4109...
Need help?
Do you have a question about the PD202326A and is the answer not in the manual?
Questions and answers