Table of Contents
Advertisement
Quick Links
18V Cordless Jig Saw
68242 18V Cordless Jig Saw
Read this material before using this product.
Failure to do so can result in serious injury.
Save this manual.
When unpacking, make sure that the product is intact and undamaged.
If any parts are missing or broken, please call 1-800-444-3353 as soon as possible.
©
Copyright
2010 by Harbor Freight Tools
or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.
Manual Revised 11a
Visit our website at: http://www.harborfreight.com
®
. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape
Advertisement
Table of Contents
Related Manuals for Drill Master 68242
Summary of Contents for Drill Master 68242
- Page 1 . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein.
-
Page 2: Specifications
Remove any adjusting key or wrench NOTICE is used to address practices before turning the power tool on. A wrench not related to personal injury. REV 11a Page 2 For technical questions, please call 1-800-444-3353. SKU 68242... -
Page 3: Jig Saw Safety Warnings
Use of the power tool for operations different from those intended could result in a hazardous situation. SKU 68242 For technical questions, please call 1-800-444-3353. Page 3... -
Page 4: Vibration Safety
It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Page 4 For technical questions, please call 1-800-444-3353. SKU 68242... -
Page 5: Extension Cords
Association, and the National Electrical Code. 2. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. (See Outlets for 2-Prong Plug.) SKU 68242 For technical questions, please call 1-800-444-3353. Page 5... -
Page 6: Instructions For Putting Into Use
Note: For additional information regarding the parts listed in the following pages, refer to Parts List and Assembly Diagram on page 1011. Lock Button Trigger Battery Pack Blade Cover Battery Button Base Plate Blade Page 6 For technical questions, please call 1-800-444-3353. SKU 68242... -
Page 7: Tool Set Up
7. Allow the Battery Pack to cool completely before using it. 8. Press the Battery Button to release Battery Pack from the Charger (or when removing it from the Saw). REV 11a SKU 68242 For technical questions, please call 1-800-444-3353. Page 7... -
Page 8: Maintenance And Servicing
1. BEFORE EACH USE, inspect the general condition of the tool. Check for loose hardware, misalignment WARNING! Wear ANSI-approved safety goggles and or binding of moving parts, cracked or broken heavy-duty work gloves whenever changing the Blade. Page 8 For technical questions, please call 1-800-444-3353. SKU 68242... -
Page 9: Troubleshooting
4. Wear ANSI-approved safety goggles and NIOSH- approved dust mask/respirator while blowing dust out of motor using compressed air. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. SKU 68242 For technical questions, please call 1-800-444-3353. Page 9... -
Page 10: Parts List And Assembly Diagram
Angle Plate Bearing Base Plate Motor Gear Pulley Bracket Battery Pack Motor Hex Wrench Mount Left Housing Blade Cover Left Housing Trim Reciprocating Shaft Spring Blade Plate Screw Set Screw Page 10 For technical questions, please call 1-800-444-3353. SKU 68242... -
Page 11: Assembly Diagram
Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 68242 For technical questions, please call 1-800-444-3353. Page 11... -
Page 12: Limited 90-Day Warranty
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance.