Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Owner's Manual & Safety Instructions
Save This Manual
operating, inspection, maintenance and cleaning procedures. Write the product's serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
Email our technical support at: productsupport@harborfreight.com
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
©
Copyright
2010 by Harbor Freight Tools
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Keep this manual for the safety warnings and precautions, assembly,
Visit our website at: http://www.harborfreight.com
®
. All rights reserved.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
REV 15f
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Drill Master 68242
Summary of Contents for Drill Master 68242
- Page 1 Owner’s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
-
Page 2: Specifications
Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. Page 2 For technical questions, please call 1-888-866-5797. Item 68242... -
Page 3: Jig Saw Safety Warnings
5. Battery tool use and care a. Recharge only with the charger specified by the manufacturer. A charger that is suitable Item 68242 For technical questions, please call 1-888-866-5797. Page 3... -
Page 4: Vibration Safety
(California Health & Safety Code § 25249.5, et seq.) 12. WARNING: This product contains di (2-ethylhexyl) phthalate (DEHP), a chemical known to the State of California to cause cancer and birth defects Page 4 For technical questions, please call 1-888-866-5797. Item 68242... -
Page 5: Extension Cords
Association, and the National Electrical Code. 2. Double insulated tools may be used in either of the 120 volt outlets shown in the preceding illustration. (See Outlets for 2-Prong Plug.) Item 68242 For technical questions, please call 1-888-866-5797. Page 5... -
Page 6: Instructions For Putting Into Use
Note: For additional information regarding the parts listed in the following pages, refer to Parts List and Assembly Diagram on page 10. Lock Button Trigger Battery Pack Blade Cover Battery Button Base Plate Blade Page 6 For technical questions, please call 1-888-866-5797. Item 68242... -
Page 7: Tool Set Up
9. Press the Battery Button to release Battery Pack from c. Slide the Blade’s mounting edge into the Charger (or when removing it from the Saw). the groove as far as it will go. Item 68242 For technical questions, please call 1-888-866-5797. Page 7... -
Page 8: Maintenance And Servicing
Blade. 1. BEFORE EACH USE, inspect the general condition of the tool. Check for loose hardware, misalignment or binding of moving parts, cracked or broken Page 8 For technical questions, please call 1-888-866-5797. Item 68242... -
Page 9: Troubleshooting
4. Wear ANSI-approved safety goggles and NIOSH- approved dust mask/respirator while blowing dust out of motor using compressed air. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. Item 68242 For technical questions, please call 1-888-866-5797. Page 9... -
Page 10: Parts List And Assembly Diagram
Angle Plate Bearing Base Plate Motor Gear Pulley Bracket Battery Pack Motor Hex Wrench Mount Left Housing Blade Cover Left Housing Trim Reciprocating Shaft Spring Blade Plate Screw Set Screw Page 10 For technical questions, please call 1-888-866-5797. Item 68242... - Page 11 Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Item 68242 For technical questions, please call 1-888-866-5797. Page 11...
-
Page 12: Limited 90-Day Warranty
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
Need help?
Do you have a question about the 68242 and is the answer not in the manual?
Questions and answers