Advertisement
5
Program the Camera
OSD Menu Controls
Legend
#
1
2
2
1
OSD Menu Structure
The HD4DIR/X menu system consists of one main SETUP menu (see below)
for easy camera programming.
Press down on the SETUP (MENU) control to display the SETUP menu.
Main Menu
Submenu
SHUTTER
<<SETUP MENU>>
1
LENS
DC!
2
SHUTTER
– – –
3
WHITE BAL.
ATW
BACKLIGHT
4
BACKLIGHT
OFF
5
AGC
MIDDLE!
6
DNR
MIDDLE
7
SENS-UP
OFF
8
SPECIAL!
9
EXIT MENU
! indicates submenus
SPECIAL !
SETUP Menu Functions
Menu Item
Option
Description
1
LENS
DC
Selects Lens type (the HD4DIR/X only supports DC mode at this time;
!
choosing any other mode may cause incorrect/unpredictable camera
VIDEO
operation).
MANUAL
2
SHUTTER
FLK
Adjusts shutter settings.
ESC
Flickerless mode (FLK) reduces on-screen flickering.
!
MANUAL
Electronic Shutter Control (ESC) adjusts brightness level on screen.
Manual mode allows you to adjust the shutter speed from 1/60-1/
120,000 of a second (NTSC), or 1/50-1/120,000 (PAL).
FLK is the only option available when the camera lens is set to the
recommended DC mode.
3
WHITE BAL.
ATW
Controls color on the screen.
MANUAL
Select Auto Tracing White Balance (ATW) when the color temp is
!
(White Balance)
2400°K-12000°K (for example when under a fluorescent light, or
AWC
!
outdoors).
Manual mode allows you to increase or decrease the red or blue
factor on screen.
Auto White Balance Control (AWC) automatically adjusts the white
balance to your specific environment.
4
BACKLIGHT
OFF
Provides light level control to overcome severe
backlighting conditions.
LOW
MIDDLE
HIGH
5
AGC
OFF
Adjusts value of AGC gain.
LOW
Increase the GAIN level to brighten the picture
!
(Automatic Gain
(noise/distortion may develop).
MIDDLE
!
Control)
HIGH
!
6
DNR
OFF
Reduces noise/distortion on the screen. Increasing the DNR level
reduces noise but may introduce video artifacts. DNR is deactivated if
LOW
(Digital Noise
AGC is turned off.
MIDDLE
Reduction)
HIGH
7
SENS-UP
OFF
Automatically provides a clear image under low-light conditions. You
can control the maximum low-light magnification from 2x to 128x
AUTO
!
(increasing magnification may cause noise/distortion). SENS-UP is
deactivated when SHUTTER is set to FLK mode.
8
SPECIAL
Takes you to the SPECIAL menu (see "SPECIAL Menu" below).
!
9
EXIT
Exits the SETUP menu and returns to video monitoring.
SPECIAL Menu
1.
On the SETUP menu, press the menu control UP or DOWN and then
select SPECIAL.
2.
Press the SETUP (MENU) control to access the SPECIAL menu.
<<SPECIAL MENU>>
1
CAMERA ID
2
DAY/NIGHT
3
SYNC
4
MOTION DET
5
PRIVACY
6
MIRROR
7
SHARPNESS
8
RESET
9
RETURN!
© 2008 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written
permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects. However, Honeywell
Video Systems cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject
to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.
Description
Video-test monitor output connector
Camera OSD joystick control (four position plus center push)
Press this control
To do this
UP, DOWN
Select a new item
LEFT, RIGHT
Select a menu item
SETUP (MENU)
Enter SETUP MENU,
(CENTER PUSH)
access a submenu
Menu Options
LENS
DC! , VIDEO, MANUAL
FLK, ESC! , MANUAL
WHITE
ATW, MANUAL! , AWC!
BAL.
OFF, LOW, MIDDLE, HIGH
AGC
OFF, LOW! , MIDDLE! , HIGH!
DNR
OFF, LOW, MIDDLE, HIGH
SENS-UP
!
OFF, AUTO
See "SPECIAL Menu Functions"
on page 2.
OFF
AUTO
INT
OFF
OFF
OFF
ON!
! indicates submenus
SPECIAL Menu Functions
Menu Item
Option Description
1
CAMERA ID
OFF
Display a name and/or number on the monitor. To add a camera title:
ON
UP, DOWN, LEFT, or RIGHT menu control = select a character, then pre
CAMERA ID
(SETUP) MENU to accept it. The character is saved and the title cursor at
bottom of the screen moves to the next position.
A B C D E F G H I J K L M
" $ = go back or forward in the title name to make changes.
N O P R Q S T U V W X Y Z
a b c d e f g h i j k l m
CLR
= delete the entire name and start again.
n o p q r s t u v w x y z
– .
0 1 2 3 4 5 6 7 8 9
POS = position the camera title on the screen. Press (SETUP) MENU to
confirm the position.
" $ CLR POS END
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _
END = accept the new name.
2
DAY/NIGHT
COLOR
COLOR = Full-time color mode.
AUTO
AUTO = Automatically detect color or black/white.
B/S
B/W = Full-time monochrome.
3
SYNC
INT
INT = Synchronize the vertical interval sync pulse of your camera with
L/L
other equipment to reduce the effect of picture roll on the monitor.
L/L (Line Lock) = adjust the phase from 0° - 359°.
Menu Item
<SYNC. CONTROL>
INTERNAL
SYNC
INT (L/L)
LINELOCK
RETURN!
RETURN
4
MOTION DET
OFF
Detect moving objects on screen; displays MOTION DETECTED
ON!
along with the number of movements counted. Select the area on
screen you want to observe.
Menu Item Option Description
MOTION DETECTION
AREA SEL
AREA SEL
AREA 1
AREA STATE ON
TOP
|..|................| 10
DOWN
|........|..........| 25
LEFT
|...|...............| 20
AREA STATE
RIGHT
|........|..........| 40
Press SET to Return
TOP
DOWN
LEFT
RIGHT
5
PRIVACY
OFF
Mask up to 4 areas of the screen from video monitoring.
ON!
Menu Item Option Description
PRIVACY
AREA SEL
AREA SEL
AREA 1
AREA STATE ON
AREA TONE
|...............|...| 80
TOP
|..|................| 10
DOWN
|........|..........| 25
AREA STATE
LEFT
|...|...............| 20
RIGHT
|........|..........| 40
AREA TONE
Press SET to Return
TOP
DOWN
LEFT
RIGHT
6
MIRROR
OFF
Produce a horizontal mirror image on screen.
ON
7
SHARPNESS
ON!
Sharpen the image on screen (image level 0 - 31). Excessive
OFF
sharpening may cause picture noise.
8
RESET
Restore all factory default settings.
9
RETURN!
Return to the main SETUP menu.
6
Install the Enclosure Cover
Description
When line lock is not required.
Adjust the vertical phase (VPH) from 000 – 359
(factory default is 0). Line-lock is only available with
24 VAC power.
Press MENU to return to the SETUP menu.
AREA 1
Select a motion detection grid (top left,
AREA 2
top right, bottom left, bottom right) to
AREA 3
modify.
AREA 4
ON
Activate or deactivate the selected grid.
OFF
Press LEFT or RIGHT menu control left
or right to alter the dimensions of the
selected grid.
AREA 1
Select a masking grid (top left, top right,
AREA 2
bottom left, bottom right) to modify.
AREA 3
AREA 4
ON
Activate/deactivate the selected grid.
OFF
Press LEFT or RIGHT menu control to
change the shade of the masking grids.
Press LEFT or RIGHT menu control to
alter the dimensions of the selected grid.
Camera dome
enclosure
Use Allen key to secure dome
enclosure to base (#8-32
security screws (x4)
www.honeywellvideo.com
+1.800.796.CCTV (North America only)
HVSsupport@honeywell.com
Document 800-01528 – Rev A – 02/08
Advertisement
