Honeywell HD4DIR Quick Install Manual

HD4DIR/HD4DIRX Camera Quick Install Guide
Thank you for purchasing a Honeywell Day/Night IR Fixed Dome Camera.
Before installing the camera, please verify your model and read this guide
carefully.
Model Signal
HD4DIR NTSC
HD4DIRX PAL
Warnings
Installation and servicing should be performed only by qualified and experienced
technicians to conform to all local codes and to maintain your warranty.
Warning 12 VDC/24 VAC models require the use of CSA Certified/UL Listed
Class 2 power adapters to ensure compliance with electrical safety
standards.
WEEE (Waste Electrical and Electronic Equipment). Within the
European Union and other European countries with separate
collection systems, this product should be disposed of, at the end
of its useful life, as per applicable local laws, regulations, and
procedures.

FCC Compliance

Information to the User: This equipment has been tested and found to comply with
the limits for a Class B digital device. Pursuant to Part 15 of the FCC Rules, these limits
are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference. For example, try reorienting or relocating the receiving
antenna, increasing the separation between the equipment and receiver, or connecting
the equipment to an outlet on a different circuit.
Caution Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Manufacturer's Declaration of Conformance
The manufacturer declares that the equipment supplied with this guide is compliant
with the essential protection requirements of the EMC directive 89/336/EEC and the
Low Voltage Directive LVD 73/23 EEC, conforming to the requirements of standards EN
55013 for emissions, EN 50130-4 for immunity, and EN 60065 for Electrical Equipment
safety.

Unpack Everything

You will also require a Phillips screwdriver and side-cutters.
1
Prepare for Installation
1. Use the mounting template to mark and pre-drill the holes.
2. Connect the cables:
Through the grommet in the housing base
Through the side conduit
Document 800-01528 – Rev A – 02/08
Vari-focal Auto Iris Lens
3.3 - 12 mm
3.3 - 12 mm
HD4DIR/X Camera
+ factory-installed pigtail power and video
connectors
This guide
Mounting template
Hardware Kit
Allen wrenches (x3)
8-32 x 1/8" screws (x4)
#6 - 1 7/16" slotted Type A screws (x4)
a. Use a sharp knife to cut an opening in
the base gasket ! only large enough to
feed the cable assembly through.
b. Apply sealant around the opening.
c. Peel back the bottom flat gasket below
the side conduit to expose the security
screw.
d. Use the Allen key to remove the security
screw.
e. Unscrew the conduit plug.
f. Pull the cabling through the hole.
g. Apply appropriate sealant around the
opening.
2

Mount the Camera

Surface Mount Installations Without an Electrical Box
Secure the camera to a wall or ceiling using #6-1 7/16 inch slotted Type A
screws (x4) supplied.
4S Electrical Box Installation
Ceiling/wall
Optional: Secure
adapter plate to the
4S electrical box.
Secure the base
with supplied
screws.
Note For wall mount installations, orient the conduit plug face down
to prevent moisture from entering housing.
Single Gang Electrical Box Installation
Ceiling/wall
Secure the base with
screws appropriate
to your installation
(not supplied)
3
Connect the Wiring
Video: female BNC
(yellow)
Power: 12 VDC
or 24 VAC
4
Adjust the Camera
1. Connect the video-test
monitor to the output
connector.
2. Adjust the 3D gimble as
shown below to obtain
the desired field of view.
Legend
A = Tilt rotation
B = Horizontal rotation
C = Pan rotation
*To switch between
Line Lock and Internal,
use OSD menus (see
"SYNC" in the
"SPECIAL Menu
Functions").
Note Line Lock On/Off switch is located on the power board. Please
leave "ON".
3. Retighten the locking screws.
Make Final Adjustments to Lens Focus
Lenses are pre-focused at the factory. In the unlikely event the optical effect
of the dome causes a slight defocusing of the lens, hold the dome over the
lens to make a final adjustment.
Electrical box
(not supplied)
Screws (not supplied)
Camera base
#6- 1 7/16 Inch
slotted Type A screws
(surface mount
without electrical box)
Electrical box
(not supplied)
Camera base
#6- 1 7/16 Inch slotted Type A
screws (surface mount without
electrical box)
Note For secure
installations, protect
surface mounted
cables with plastic or
metal cable covers.
+ Red
- Black
If necessary, loosen
locking screw with a
Phillips screwdriver to
B
adjust Horizontal (B).
If necessary, loosen
C
the setscrews (x2)
with an Allen key to
adjust Pan (C).
Set focal length (top)
A
Set focus (bottom)