Table of Contents
Related Manuals for Husqvarna 326HS75 X-series
Summary of Contents for Husqvarna 326HS75 X-series
- Page 1 Oper ator’s manual (EPA) 326HS75 X-series 326HS99 X-series Please r ead the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h understand the instructions before using the machine.
-
Page 2: Key To Symbols
KEY T O SYMBOLS Symbols The engine is s witched off by moving the stop switch to the stop position. CAUTION! The stop switch automatically returns to the start W ARNING! Incorrect or careless use of a position. In order to prevent unintentional hedge trimmer can turn it into a dangerous starting, the spark plug cap must be removed tool that can cause serious or even fatal... -
Page 3: Table Of Contents
CONTENTS Contents Note the f ollowing before starting: KEY TO SYMBOLS Please read the oper ator’s manual carefully. Symbols ............... Long-term exposure to noise can result in permanent hearing CONTENTS impairment. So always use approved hearing protection. Contents ..............Maintenance, replacement, or repair of the emission control Note the following before starting: ........ -
Page 4: Intr Oduction
Dear customer! Cong ratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant. -
Page 5: What Is What
WHA T IS WHA T? What is what? 1 Operator’s manual 12 Choke control 2 Grease nipple 13 Throttle lock 3 Gear housing 14 Throttle control 4 Blades 15 Stop switch 5 Hand guard 16 Air filter cover. 6 Front handle 17 Combination spanner 7 Cylinder cover 18 Allen key... -
Page 6: General Safety Preca Utions
GENERAL SAFETY PRECA UTIONS Impor tant W ARNING! Listen out for warning signals or shouts when you are wearing hearing protection. Always remove your hearing IMPORTANT! protection as soon as the engine stops. The machine is only designed for cutting branches and HEARING PR OTECTION twigs. - Page 7 GENERAL SAFETY PRECA UTIONS The lif e span of the machine can be reduced and the risk of Check that the throttle control and throttle lock move freely accidents can increase if machine maintenance is not carried and that the return springs work properly. out correctly and if service and/or repairs are not carried out professionally.
- Page 8 GENERAL SAFETY PRECA UTIONS Vibration damping system Never use a machine that has a faulty muffler. Y our machine is equipped with a vibration damping system that is designed to reduce vibration and make operation easier. The machine ′ s vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment and Regularly check that the muffler is securely attached to the the machine ′...
- Page 9 GENERAL SAFETY PRECAUTIONS Blades To ensure good cutting results it is important that the contact pressure between the blades is correct. The contact pressure is adjusted by turning the screws on the underside of the bar clockwise as far as they will go. Then turn the screws anticlockwise a 1/4 turn.
-
Page 10: Fuel Handling
• In order to prevent unintentional starting of the engine, the • For best results and performance use HUSQVARNA two- spark plug cap must always be removed during long-term stroke engine oil, which is specially formulated for our air- storage, if the machine is not under close supervision and cooled two stroke-engines. -
Page 11: Fueling
FUEL HANDLING Mixing Fueling • Always mix the gasoline and oil in a clean container intended for fuel. • Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. -
Page 12: Starting And Stopping
STARTING AND STOPPING Check before starting Starting and stopping • Inspect the working area. Remove any objects that could be thrown out. WARNING! The complete clutch cover and gear housing must be fitted before the • Check the cutting attachment. Never use blades that are machine is started, otherwise the clutch may dull, cracked or damaged. - Page 13 STARTING AND STOPPING Starting Hold the body of the machine on the ground using your left hand (CAUTION! Not with your foot!). Grip the starter handle, slowly pull out the cord with your right hand until you feel some resistance (the starter pawls grip), now quickly and powerfully pull the cord.
-
Page 14: Working Techniques
WORKING TECHNIQUES General working instructions Safety instructions while working IMPORTANT! • Always ensure you have a safe and stable working This section takes up the basic safety precautions for position. working with a hedge trimmer. • Always use both hands to hold the machine. Hold the If you encounter a situation where you are uncertain how to machine in front of your body. -
Page 15: Basic Working Techniques
WORKING TECHNIQUES Safety instructions after completing work • The transport guard should always be fitted to the cutting attachment when the machine is not in use. • Make sure the cutting attachment has stopped before cleaning, carrying out repairs or an inspection. Disconnect the HT lead from the spark plug. -
Page 16: Maintenance
Basic setting • The basic carburetor settings are adjusted during testing Your Husqvarna product has been designed and at the factory. The basic setting is richer than the optimal manufactured to specifications that reduce harmful setting and should be maintained for the first few hours the emissions. -
Page 17: Muffler
MAINTENANCE Fine adjustment of the idle speed T Correctly adjusted carburetor Adjust the idle speed with the idle adjustment screw T, if When the carburetor is correctly adjusted the machine adjustment is necessary. First turn the idle adjustment screw accelerates without hesitation and burbles a little at maximum T clockwise until the blades start to move. -
Page 18: Cooling System
These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The difficulties. filter oil contains a solvent to make it spread evenly through the filter. -
Page 19: Gear Housing
There is a grease nipple and a plug for filling lubricant on the gear housing. Use a grease gun to fill with grease. This should be done after every 60 working hours. Use Husqvarna’s special grease, no. 503 98 96-01. -
Page 20: Maintenance Schedule
MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this manual. More extensive work must be carried out by an authorised service workshop. -
Page 21: Technical D Atat Echnical Data
TECHNICAL DATA Technical data Technical data 326HS75 326HS99 Engine Cylinder displacement, cu.in/cm 1,50/24,5 1,50/24,5 Cylinder bore, inch/mm 1,34/34,0 1,34/34,0 Stroke, inch/mm 1,06/27 1,06/27 Idle speed, rpm 2700 2700 Recommended max. fast idle speed, rpm 11000-12600 11000-12600 Max. engine output, acc. to ISO 8893, kW/ rpm 0,9/9000 0,9/9000 Catalytic converter muffler... -
Page 22: Federal Emission Control Warranty Statement
Forest & Garden cannot deny warranty solely for the lack of servicing dealer or call Husqvarna Forest & Garden at 1-800- receipts or for your failure to ensure the performance of all 487-5963. - Page 24 1150090-95 ´®z+R))¶5J¨ ´®z+R))¶5J¨ 2005-06-01...