Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Emotiva XSP-1
Summary of Contents for Emotiva XSP-1
-
Page 3: Important Safety Precautions And Explanation Of Symbols
Do not install the XSP-1 on any stand, shelf, or other piece of furniture that is unable to support its weight. If a cart is used to move the unit, use caution to avoid injury from tip-over. - Page 4 Only replace the fuse(s) in the XSP-1 with fuse(s) of proper value and voltage rating. The XSP-1 should only be cleaned as directed in the Manual. Avoid spraying liquids directly onto the unit and NEVER spray liquids into the vents. Care should be taken so that small objects do not fall into the inside of the unit.
-
Page 5: Table Of Contents
XSP-1 XSP-1 Differential Reference Stereo Preamplifier Contents Important Safety Precautions and Explanation of Symbols XSP-1 Differential reference Stereo Preamplifier .......1 Introduction ..................3 About This Manual ................4 Features .....................5 Unpacking...................6 XSP-1 Front Panel................7 XSP-1 Rear Panel ................10 Quick Start ..................15 Connections..................16 Configuration and Operation ............19... - Page 6 XSP-1 Page 2...
-
Page 7: Introduction
Introduction Thank you for purchasing your new XSP-1 Differential Reference stereo preamplifier. The XSP-1 is the result of a two-year development effort aimed at creating a reference-caliber, fully balanced, analog stereo preamplifier. The XSP-1 Differential Reference preamplifier offers the ultimate in sound quality and control for audiophiles who are searching for the finest possible stereo listening experience. -
Page 8: About This Manual
About This Manual This manual will provide you with the information you need to get started enjoying your XSP-1 stereo preamplifier. For more information about the XSP-1 and our other products, please visit our website at www.emotiva.com. We suggest that you read through the entire manual; we kept things as short and direct as possible. -
Page 9: Features
The pure analog signal path in the XSP-1 is complemented by the convenience and precision of digital control. Output level on the XSP-1 is set via a precision digital encoder, which instructs a digitally controlled analog resistor ladder network, and which provides near-perfect channel matching and absolute repeatability. -
Page 10: Unpacking
XSP-1 Unpacking Your XSP-1 was carefully packed and should reach you in perfect condition. If you notice any shipping damage or other issues when you unpack it, please contact Emotiva immediately. Gently remove your XSP-1 from the packing carton and remove all wrappings and shipping material. -
Page 11: Xsp-1 Front Panel
When you press this button, the source connected to the Home Theater Inputs is routed directly to the Main Outputs on the XSP-1, bypassing all controls including the level control and bass management. The display will indicate Home Theater Bypass when this is active. -
Page 12: Volume Knob
Loop status. 5. VFD (vacuum fluorescent display) The VFD displays all status on the XSP-1, including level, Trim status, and the input that is selected. The VFD brightness can be adjusted in ten levels (using the Dim Button). 6. Volume Knob Rotate the Volume knob clockwise to turn the Volume up;... -
Page 13: Standby Button
Input is selected and returns to it when turned On. 12. Mute Button Press the Mute button once to mute the output of the XSP-1; press it again to return to the previously selected level. Pressing the Mute button mutes both the main outputs and the headphone outputs. -
Page 14: Xsp-1 Rear Panel
4. Processor Loop Output (unbalanced) This output provides a copy of the signal received on the selected input of the XSP-1. The Processor Loop is equivalent to what used to commonly be called a “tape monitor”. -
Page 15: Phono Input
Most external phono preamps output a line level signal, which must be connected to one of the other inputs on the XSP-1. (If in doubt, please contact Emotiva Tech Support or the makers of your phono preamp.) 7. -
Page 16: High Pass Crossover Frequency Adjustment
13. IR In and IR Out The IR Input is used to allow IR control of the XSP-1 even if it’s located inside a cabinet or in another room, and accepts the output of most standard IR receiver modules. -
Page 17: Main Outputs
XSP-1 14. Trigger In and Trigger Out The Trigger Input accepts a standard trigger signal to allow the XSP-1 to be turned on (from Standby) by other equipment. The Trigger Output sends out a standard 12 VDC trigger signal which can be used to turn on other equipment (the Trigger Output is active only when the XSP-1 is On). -
Page 18: Subwoofer Outputs
3 dB on the Left and Right Outputs). 19. AC Power Switch Switches the main AC power to the XSP-1 On and Off. When this switch is Off, no controls operate (the XSP-1 cannot be turned On from the front panel or remote control). -
Page 19: Quick Start
XSP-1 Quick Start To get the most from your XSP-1, we urge you to read the entire manual. If you just can’t wait to listen to it, this section will cover the basics you need to get started. • Find a secure location for your XSP-1. -
Page 20: Connections
Connecting a turntable to your XSP-1 The outputs from the phono cartridge on a turntable should be connected to the Phono Input on the XSP-1. If a ground lead is provided, it should be connected to the Phono Ground terminal on the XSP-1. - Page 21 XSP-1 will return to Standby mode. The Trigger Output sends out 12 VDC whenever the main power to the XSP-1 is On (and NOT when it is in Standby mode) which can be used to switch on other units with trigger capabilities.
- Page 22 A typical combination stereo and home theater system. When Home Theater Bypass on the XSP-1 is engaged, the Pre / Pro supplies signal for all channels, and the XSP-1 passes the signals destined for the main speakers (Front Left and Front Right) and subwoofer without modification.
-
Page 23: Configuration And Operation
Configuration and Operation Line Voltage The XSP-1 can operate from line voltages of 115 VAC +/- 10% or 230 VAC +/- 10%; when the unit is powered on, it will automatically detect the correct line voltage and set itself accordingly. -
Page 24: Remote Control
(Main Outputs are set to Full Range). Max Start-up Volume Normally, when the XSP-1 is turned On, it ramps up to the level which was selected when it was turned Off or put into Standby. This feature allows you to set a maximum limit on that level. - Page 25 XSP-1 Frequency Trim Controls Pressing the Direct Button toggles the Frequency Trim function on and off; the VFD will display the status.). To view the HF adjustment level, press the HF Trim Button; while the HF Trim level is displayed, use the Boost and Cut buttons to adjust it. To view the LF adjustment level, press the LF Trim Button;...
-
Page 26: Care And Maintenance
If necessary, the XSP-1 should be cleaned gently with a soft rag. • If something sticky gets on the front panel or case of the XSP-1, it should be cleaned with a mild cleaning solution applied to a soft rag, followed by wiping with a clean rag dampened with plain water and drying with a soft dry rag or cloth. -
Page 27: Specifications
XSP-1 Specifications Topology: Fully differential signal path, with balanced inputs and outputs; all input switching via silver clad relay contacts; level control via digitally controlled analog resistor ladder network. Includes analog bass management, true processor loop, and home theater bypass functions. -
Page 28: Frequency Response
XSP-1 Gain Structure: Nominal Output Level: 0 dB = 1 V. Nominal Gain (Volume set to “0”): 1. Maximum Gain (main outputs): +12 dB. Frequency Response: 20 Hz to 20 kHz +/- 0.02 dB (balanced in to balanced out). 20 Hz to 20 kHz +/- 0.015 dB (unbalanced in to unbalanced out). -
Page 29: Front Panel Controls And Indicators
XSP-1 Phono Section (moving coil, phono in to balanced out): Gain (1 kHz, Volume set to “0”): approximately 60 dB. Input impedance (user selectable): 47 ohms, 100 ohms, 470 ohms, 1k ohm. S/N (signal-to-noise ratio, A-weighted, ref 1.0 mV in): > 79 dB. -
Page 30: Power Requirements
XSP-1 Power Requirements: 115 VAC or 230 VAC +/- 10% @ 50 / 60 Hz (automatically detected and switched). Power consumption (On): 32 watts. Power consumption (Standby): <1 watt. Dimensions: 17” wide x 6” high x 16.5” deep (includes feet and terminals). -
Page 31: Troubleshooting
When using the bass management in the XSP-1, any crossover or low-pass filter on the sub itself should be disabled so it doesn’t interact with the bass management on the XSP-1 (set it to “flat” if you have that option, if not, then set it to the highest value possible.) -
Page 32: Emotiva Audio Corporation Five-Year Limited Warranty
NOT APPLY TO YOU. A claim under this warranty must be made by you within the Term. A claim shall not be valid (and Emotiva has no obligation related to the claim) if it is not made within the Term and if it is not made in strict compliance with the requirements of the “How do you get service?”... - Page 33 The CSR will provide you with a returned material authorization number (“RMA”). Ship the product to Emotiva at the following address, with the RMA written in large, bold numbers on the outside of the box, and with the letters “RMA” written before the number.
-
Page 34: Notes
Notes All information contained in this manual is accurate to the best of our knowledge at the time of publication. In keeping with our policy of ongoing product improvement, we reserve the right to make changes to the design and features of our products without prior notice. Quick Reference Manual Revision 1.0 October 2012...