How To Use Programming - Beltronics Vector V10 Owner's Manual

Programming
There are 7 user-selectable options so you
can customize your V10 to your own
preferences.The buttons labeled CITY and
BRT are also used to enter the Program
Mode,REVIEW your current program
settings,and to CHANGE any settings as
desired.The words PGM,RVW,and CHG are
located on the top of the detector,and are
highlighted in colored graphics.Pages 14-
16 explain each option in more detail.

How to use Programming

1
To enter Program Mode, press and
hold both the CITY and BRT buttons
down for 2 seconds.The unit will beep
twice,and will display the word Program.
2 Then press the RVW button to
review the current settings.You can
either tap the button to change from item
to item,or hold the button to scroll through
the items.
3
Press the CHG button to change
any setting.You can either tap the button
to change from setting to setting,or hold
the button to scroll through all the options.
4 To leave the Program Mode,
simply wait 8 seconds without
pressing any button, or press the PWR
button.The unit will display Complete,
beep 4 times,and return to normal
operation.
An example
Here is how you would turn your V10's
AutoMute feature off.
1 Enter the Program Mode by holding
both the CITY and BRT buttons down for
2 seconds. The V10 will beep twice and
display Program.
2 Then hold the RVW button down. The
V10 will scroll through the categories,
starting with Pilot (Pilot),Voice
(Voice), Power-on sequence (PwrOn),
Signal Strength Meter (Meter), and then
AutoMute (aMute).
3 Release the RVW button when the V10
shows the AutoMute item. Since the factory
setting is for AutoMute to be on, the V10
will display aMute ON.
If you accidentally don't release the
RVW button in time, and the V10 goes to
the next category, hold the RVW button
down again, and after your V10 scrolls
through all categories, it will begin again
at the top of the list.
4 Press the CHG button to change from
aMute ON to aMute OFF.
5 To complete the Programming,simply
wait 8 seconds without pressing any
button,or press the PWR button. TheV10
will display Complete, beep 4 times, and
return to normal operation.
12
Overview of Programming
Press the REVIEW button
to go from one
category to the next
PILOT
Pilot HWY
(Power-on indication)
Pilot H
Pilot V
VOICE
Voice ON
Voice OFF
POWER-ON SEQUENCE PwrOn STD
PwrOn FST
SIGNAL STRENGTH METER
Meter STD
Meter THT
Meter TEC
AUTOMUTE aMute ON
aMute OFF
CITY MODE SENSITIVITY
City STD
City LoX
City NoX
BANDS Bands DFT
Bands MOD
*
Factory Default Settings
To reset your V10 to its original
factory settings,press and hold
the"CITY"and"BRT"buttons
while turning the power on.The
V10's display will provide a
Reset
message,accompanied
by an audible alert,
acknowledging the reset.
Press the CHANGE button
to change your setting
within a category
* Full word: Highway, AutoScan or City
Letter: H or A or C
Vehicle voltage
* Voice alerts on
Voice alerts off
* Standard power-on sequence
Fast power-on sequence
* Standard signal strength meter
Threat Display
Tech Display
* AutoMute on
AutoMute off
* Standard City mode sensitivity
Low X band sensitivity in City Mode
No X band sensitivity in City Mode
* All band enabled
One or more bands are disabled
Turn bands "ON" or "OFF" by
pressing the VOLUME•MUTE button
X ON or OFF (default is ON)
or OFF (default is ON)
K ON
TSR ON or OFF (default is ON)
Ka USA* or Intl or OFF
POP ON or OFF (default is OFF)
LSR ON or OFF (default is ON)
SWS ON or OFF (default is OFF)
13