Table of Contents
Advertisement
Progressor II™
Caution: Always replace with the exact same type lamp and fuse,
unless otherwise specified by an authorized American DJ
Replacing with anything other than the specified part can damage the
unit and will void the manufactures warranty.
Warning: If, after replacing the lamp or fuse either one continues
to blow, STOP using the unit. Contact customer support for further
instructions, you may have to return the unit for servicing. Continuing
to use the unit may cause serious damage.
Fuse Replacement: Disconnect the unit's main power supply. Insert a
standard flat head screw driver in to the fuse holder housing. Turn the
screwdriver in counter-clockwise direction to remove the fuse holder.
Remove the fuse holder to expose the fuse. Remove the old fuse and
discard it. Replace the fuse with the same type. Insert the fuse holder
back into it's housing and turn it in clockwise direction to lock the
holder in place.
Lamp Replacement: Caution! Never attempt to change the lamp
while the fixture is plugged in. Always disconnect the main power
and allow the unit ample time to cool before attempting to replace the
lamp. Lamp replacement has been made simple by incorporating the
use of a flip-up top cover that is retained by a single thumb screw.
1. Be sure to follow the proper handling procedures that deal
with halogen lamps.
2. Remove the single thumb screw located in the top of the unit.
3. Flip-down the front cover to access the lamp socket assembly.
The
cover is on hinges and will not fall off.
4. Carefully remove the old lamp and discard it in the trash.
5. Replace the lamp with an exact match and reassemble.
Halogen Lamp Warning:
This fi xture is fi tted with a halogen lamp which is
highly susceptible to damage if improperly han-
dled. Never touch the lamp with your bare fi ngers
as the oil from your hands will shorten lamp life.
Also, never move the fi xture until the lamp has
had ample time to cool. Remember, lamps are not
covered under warranty conditions.
American DJ
- www.americandj.com - Progressor II™ Instruction Manual Page 11
©
®
Fuse & Lamp Replacement
technician.
®
Progressor II™
Trouble Shooting:
Listed below are a few common problems that you may encounter,
with solutions.
No light output from the unit;
1. Be sure you have connected your unit into a standard 120V (or
220v depending on the models voltage requirements) wall outlet.
2. Be sure the external fuse has not blown. The fuse is located on
the rear panel of the unit.
3. Remove the lamp cover and be sure the lamp is seated in its
socket properly. Occasionally lamps become loose during ship-
ping be sure the lamp is push in to its socket all the way. Rem-
ember not to touch the lamp with your bare fingers.
4. Be sure the fuse holder is completely and properly seated.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
not activate the unit.
2. Be sure the SENSITIVITY KNOB (1) is not set to the maximum
position.
Progressor II™
Fixture Cleaning:
Due to fog residue, smoke, and dust cleaning the internal and exter-
nal optical lenses and mirror should be carried out periodically to
optimize light output. Cleaning frequency depends on the environ-
ment in which the fixture operates (I.e. smoke, fog residue, dust,
dew). In heavy club use we recommend cleaning on a monthly basis.
Periodic cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external lens with glass cleaner and a soft cloth every
20 days.
4. Clean the internal lens with glass cleaner and a soft cloth every
30-60 days.
5. Always be sure to dry all parts completely before plugging the unit
back in.
American DJ
- www.americandj.com - Progressor II™ Instruction Manual Page 12
©
®
Trouble Shooting
Cleaning
Advertisement
Table of Contents
