Troubleshooting Guide; Technical Service - Heath Zenith 5212 Specification Sheet

SYMPTOM POSSIBLE CAUSE
Light will not 1. Light switch is turned off.
come on. 2. Lamp is loose or burned out.
3. Fuse is blown or circuit breaker is turned off.
4. Daylight turn-off is in effect (recheck after
dark).
5. Re-aim the sensor to cover desired area.
6. Cable not fully plugged in.
Light comes on 1. Light Control may be installed in a relatively
in daylight. dark location.
2. Light Control is in Test (Set control switch
to an ON-TIME position).
Light comes on
1. Light Control may be sensing small animals
for no apparent
or automobile traffic (re-aim sensor).
reason. 2. Sensitivity is set too high (Reduce sensitiv-
ity).
If you experience a problem, follow this guide. You may also want to visit our Web site at: www.desatech.com. If the
problem persists, call* for assistance at 1-800-858-8501, 7:30 AM to 4:30 PM CST (M-F). You may also write* to:
DESA Specialty Products™
P.O. Box 90004, Bowling Green, KY 42102-9004
ATTN: Technical Service Specialty Products
* If contacting Technical Service, please have the following information available: Model Number, Date of Pur-
chase, and Place of Purchase.
This is a "Limited Warranty" which gives you specific legal rights. You may also have other rights which vary from state to state or province to province.
For a period of five years from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected at no
charge to you. Light bulbs are not covered. To obtain a refund or a replacement, return the product to the place of purchase.
Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs and other expendable items are not
covered by this warranty. Unauthorized service or modification of the product or of any furnished component will void this warranty in its entirety.
This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use, or unauthorized service.
This warranty covers only DESA Specialty Products™ assembled products and is not extended to other equipment and components that a
customer uses in conjunction with our products.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRE-
SENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE,
AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO LIABILITY ON THE PART OF
DESA SPECIALTY PRODUCTS™ FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT
LIMITED TO ANY LOSS OF BUSINESS OR PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Retain receipt for warranty claims.

TROUBLESHOOTING GUIDE

TECHNICAL SERVICE

(Do Not Send Products)
No Service Parts Available for this Product
FIVE YEAR LIMITED WARRANTY
SYMPTOM POSSIBLE CAUSE
Light stays on 1. A sensor is positioned too close to the lamp
continuously.
2. Light Control is pointed toward a heat
3. Sensor is in Manual Mode (Set to Auto
Light flashes on
1. Heat or light from the lamp may be turning
and off.
2. Heatbeingreflectedfromotherobjectsmaybe
3. Light Control is in theTest mode and warm-
4
or pointed at nearby objects that cause heat
to trigger the sensor (Reposition the lamp
away from the sensor or nearby objects).
source like an air vent, dryer vent, or
brightly-painted heat-reflective surface
(Reposition sensor).
Mode).
the Light Control on and off (Reposition the
sensor away from the light).
affecting the sensor (Reposition sensor).
ing up (Flashing is normal under these
conditions).
595-5734-04