Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Waldorf FN8127E
Summary of Contents for Waldorf FN8127E
- Page 1 I n s t a l l a t i o n a n d O p e r a t i o n M a n u a l Electric Deep Fryer FN8127E FNL8127E FN8127EE FNL8127EE FN8127E21 FNL8127E21 FN8127EE21...
- Page 2 MANUFACTURED BY Moffat Limited Christchurch New Zealand INTERNATIONAL CONTACTS AUSTRALIA Moffat Pty Limited Web: www.moffat.com.au E.Mail: vsales@moffat.com.au Main Office: (tel) +61 (03) 9518 3888 (fax) +61 (03) 9518 3833 Service: (tel): 1800 622 216 Spares: (tel): 1800 337 963 Customer Service: (tel): 1800 335 315 (fax): 1800 350 281...
-
Page 3: Table Of Contents
Commissioning Operation ....................10 Operation Guide Description of the Controls - FN8127E and FN8224E Models Only Description of the Controls - FN8127EE and FN8224EE Models Only Control Panel Functions - FN8127EE and FN8224EE Models Only Controller Basic Programming Mode - FN8127EE andFN8224EE Models Only... -
Page 4: Fault Finding
Fault Finding ................... 20 Guide to Cooking Problems with Fryer Fault Finding the Electrical System Wiring Schematics................... 23 FN8127E Single Tank - 17kW Model Only FN8127E21 Single Tank - 21kW Model Only FN8224E Twin Tank FN8127EE Single Tank - 17kW Model Only... -
Page 5: Introduction
Introduction We are confident that you will be delighted with your WALDORF Electric Deep Fryer, and it will become a most valued appliance in your commercial kitchen. To ensure you receive the utmost benefit from your new Waldorf Electric Deep Fryer, there are two important things you can do. -
Page 6: Specifications
IT MUST BE REPLACED BY A SUITABLY QUALIFIED PERSON IN ORDER TO AVOID A HAZARD Power Supply Amps Total Power Model Input Voltage Type Frequency FN8127E / EE 400-415Vac 3 P+N+E 50 / 60Hz 17kW 23.6 23.6 23.6 FN8127E21 / EE21 400-415Vac... -
Page 7: Dimensions
Dimensions FN(L)8127E FN(L)8224E... - Page 8 Dimensions FN(L)8127EE FN(L)8224EE...
-
Page 9: Installation
Installation shall comply with local electrical and health and safety requirements. Waldorf Deep Fryers are designed to provide years of satisfactory service, and correct installation is essential to achieve the best performance, efficiency and trouble-free operation. This appliance must be installed in accordance with National installation codes and in addition, in accordance with relevant National / Local codes covering health and safety, electrical and fire safety. -
Page 10: Fitting Rear Rollers
Installation Fitting Rear Rollers. Raise the appliance from the floor by approx. 75mm, Appliance using suitable lifting equipment (i.e. Palletiser / Forklift) Base to allow rear adjustable feet to be removed. Unscrew and remove both rear adjustable feet from rear leg housings. Fit rear roller to rear leg housing and align screw hole in side of rear leg housing with threaded hole in rear roller. -
Page 11: Electrical Connection
Installation Electrical Connection NOTE: ALL ELECTRICAL CONNECTIONS MUST ONLY BE CARRIED OUT BY A QUALIFIED PERSON. Each fryer should be connected to an adequately protected power supply and an isolation switch mounted adjacent to, but not behind the fryer. This switch must be clearly marked and readily accessible in case of fire. -
Page 12: Operation
Only authorised service persons are to carry out installation or servicing operations on this appliance. Description of the Controls - FN8127E and FN8224E Models Only FN8224E Twin Tank Model shown Temperature Control Knob Temperature Graduations 60°C to 200°C. -
Page 13: Control Panel Functions - Fn8127Ee And Fn8224Ee Models Only
Operation Control Panel Functions - FN8127EE and FN8224EE Models Only. Each control panel comprises the following:- One 4 digit, seven segment display with a 0.5” high, bright green LED display. Three green LED indicator lights located under each of the 3 Timer Controls. 6 Touch Control Keys;- ‘ON’... -
Page 14: Controller Basic Programming Mode - Fn8127Ee Andfn8224Ee Models Only
Operation Controller Basic Programming Mode - FN8127EE and FN8224EE Models Only The following Parameters can be changed in Controller Basic Programming Mode:- Timer 1 - Cook Time Settings. Timer 2 - Cook Time Settings. Timer 3 - Cook Time Settings. ... -
Page 15: Filling The Tank(S)
FN8127E and FN8224E Only;- Set the tank control thermostat to 120°C and switch ‘ON’ the appliance for 30 seconds and then ‘OFF’ for 1 minute. Repeat the cycle until all the shortening is melted enough to apply full power to the heating elements. -
Page 16: Operation Of The Appliance
USE FLAMMIBLE SOLVENTS AND CLEANING AIDS ON OR IN CLOSE PROXIMITY TO THE FRYER HOT. WHILST THE FRYER IS STILL FN8127E and FN8224E Models Only. Turn ‘ON’ mains power at the mains supply. Turn ‘ON’ mains isolator switch located behind the front access door. Green neon indicator will illuminate to indicate that there is mains power to the fryer. -
Page 17: Fn8127Ee And Fn8224Ee Models Only
Operation FN8127EE and FN8224EE Models Only. Fryer Operation (Flow Chart) Refer to ‘Controller Basic Programming Mode’ at the start of this section for the basic programmable settings for the controller. Refer to the ‘Controller Advanced Programming Mode’ section for controller advanced programming. If Melt Cycle is turned ON. -
Page 18: 'Over-Temperature' Control System
Operation To Use the Timers To Use the Temperature Display NOTE: Refer to ‘Basic Programming Mode’ for NOTE: Refer to ‘Basic Programming Mode’ for information on how to set the Timer information on how to set the Cooking Pre-Set times. Temperature. -
Page 19: Cleaning And Maintenance
Cleaning and Maintenance General Warning DO NOT USE FLAMMIBLE SOLVENTS AND CLEANING AIDS ON OR IN CLOSE PROXIMITY TO RYER WHILST HOT. RYER IS STILL Caution Always turn ‘Off’ electrical supply before cleaning the fryer. This appliance is not water proof. Do not use water jet spray to clean interior or exterior of this appliance. - Page 20 Cleaning and Maintenance Opening the Drain Valve Warning OT OIL WILL BURN OT RUSH THIS JOB a. Lift the locking slide on valve handle (Fig 6) to release the valve. b. While holding the locking slide in the withdrawn position, rotate handle anticlockwise (Fig 7) to open the valve.
-
Page 21: Weekly Cleaning
Cleaning and Maintenance Weekly Cleaning NOTE: If fryer usage is very high, we recommend that the weekly cleaning procedure is carried out more frequently. Proceed to drain and filter the tank, as shown in 'Daily Cleaning'. Do not refill the tank with frying medium until the tank has been cleaned as shown below. -
Page 22: Fault Finding
Fault Finding Guide to Cooking Problems with Fryer This section provides an easy reference guide to the more common problems that may occur during the operation of your equipment. The fault finding guide in this section is intended to help you correct, or at least accurately diagnose problems with your equipment. - Page 23 Fault Finding Fault Possible Cause Remedy Insufficient turnover of oil. Maintain a minimum quantity of oil in fryer for more rapid turnover or increase the quantity of food fried in fryer. Replace with fresh oil every 3 to 5 days. Continual frying with excess moisture on Drain foods before frying, pat food dry.
-
Page 24: Fault Finding The Electrical System
Fault Finding Fault Finding the Electrical System Fault Possible Cause Remedy Check mains power is supplied to the unit Turn ‘On’ power. Reset circuit breaker or and that a circuit breaker or fuse has not replace blown fuse. tripped / blown. Check element is flat and that the tilt Adjust microswitch so that the microswitch microswitch is closed. -
Page 25: Wiring Schematics
Wiring Schematics FN8127E Single Tank - 17kW Model Only ELEMENTS THERMOSTAT THERMOSTAT PANEL HEAT SELECTOR POWER SWITCH MICROSWITCH OVERTEMP OVERTEMP PANEL GEAR TRAY EARTH... -
Page 26: Fn8127E21 Single Tank - 21Kw Model Only
Wiring Schematics FN8127E21 Single Tank - 21kW Model Only... -
Page 27: Fn8224E Twin Tank
Wiring Schematics FN8224E Twin Tank ELEMENTS CONTROL PANEL THERMOSTAT HEAT HEAT SELECTOR SELECTOR POWER POWER SWITCH SWITCH MICROSWITCH OVERTEMP THERMOSTAT PANEL EARTH GEAR TRAY... -
Page 28: Fn8127Ee Single Tank - 17Kw Model Only
Wiring Schematics FN8127EE Single Tank - 17kW Model Only ELEMENTS BROWN BROWN CONTROL PANEL BROWN BROWN MICROSWITCH OVERTEMP OVERTEMP PANEL GEAR TRAY... -
Page 29: Fn8127Ee21 Single Tank - 21Kw Model Only
Wiring Schematics FN8127EE21 Single Tank - 21kW Model Only... -
Page 30: Fn8224Ee Twin Tank
Wiring Schematics FN8224EE Twin Tank... -
Page 31: Controller Advanced Programming Mode
Controller Advanced Programming Mode The following Parameters can be accessed and adjusted in the Advanced Programming Mode:- Timing Mode (Straight or Flexi cook time). Temperature Offset (Calibration Setting) -14° to +14°. Temperature Display Mode (Temp display or prompt display). ... -
Page 32: Temperature Offset
Controller Advanced Programming Mode Temperature Offset The display temperature can be adjusted by between -14° to +14°. Factory Default Settings O° To Calibrate the Control Temperature Set control temperature to 170°. Measure the oil temperature that the control is cycling at. higher positive ... -
Page 33: Programming The Melt Cycle
Controller Advanced Programming Mode Programming the ‘Melt Cycle’. One of the following 3 options may be selected:- ‘L’ (Liquid). ‘S’ (Solid). ‘O’ (Override). To change the programmed ‘Melt Cycle’, press either ‘Timer 1’ or ‘Timer 3’ Key to scroll through the three options. -
Page 34: Replacement Parts List
When ordering replacement parts, please quote the part number and the description as listed below. If the part required is not listed below, request the part by description and quote Model and Serial Number which is shown on the rating plate. Part No Description FN8127E FN8224E FN8127EE FN8224EE 227962...