Page 1 Table of Contents Introduction Instrument Cluster Warning lights and chimes Gauges Message center Entertainment Systems MyFord™ system Auxiliary input jack (Line in) Climate Controls Manual heating and air conditioning Automatic temperature control Touchscreen features Auxiliary passenger climate control Rear window defroster Lights Headlamps Turn signal control...
Page 2: Table Of Contents
Table of Contents Seating and Safety Restraints Seating Personal Safety System™ Safety belt system Airbags Child restraints Tires, Wheels and Loading Tire information Tire inflation Tire Pressure Monitoring System (TPMS) Vehicle loading Trailer towing Recreational towing Driving Starting Brakes AdvanceTrac Hill descent control Transmission operation Reverse sensing system...
Page 4: Introduction
Introduction CONGRATULATIONS Congratulations on acquiring your new Ford. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it.
Page 5 Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed.
Page 6 Introduction PERCHLORATE MATERIAL Certain components of this vehicle such as airbag modules, seat belt pretensioners, and button cell batteries may contain Perchlorate Material – Special handling may apply for service or vehicle end of life disposal. See www.dtsc.ca.gov/hazardouswaste/perchlorate. BREAKING-IN YOUR VEHICLE Your vehicle does not need an extensive break-in.
Page 7 Your vehicle is not equipped with a snowplowing package. Using your vehicle as an ambulance Do not use this vehicle as an ambulance. Your vehicle is not equipped with the Ford Ambulance Preparation Package. 2011 Explorer (exp) Owners Guide, 3rd Printing...
Page 8 In order to properly diagnose and service your vehicle, Ford Motor Company, Ford of Canada, and service and repair facilities may...
Page 9 EDR. Ford Motor Company and Ford of Canada do not access event data recorder...
Page 10 If you do not want Ford or its vendors to receive this information, do not activate the service. Ford Motor Company and the vendors it uses to provide you with this information do not store your vehicle travel information.
Page 11 WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that you use extreme caution when using any device or feature that may take your focus off the road. Your primary responsibility is the safe operation of your vehicle.
Page 12 Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Child Seat Lower Airbag - Side Anchor Child Seat Tether Brake System Anchor Anti-Lock Brake System Parking Brake System Brake Fluid -...
Page 13 Introduction Vehicle Symbol Glossary Power Windows Power Window Lockout Front/Rear Child Safety Door Interior Luggage Lock/Unlock Compartment Release Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, Battery Acid or Sparks Explosive Gas Fan Warning Maintain Correct Fluid...
Page 14: Instrument Cluster
Instrument Cluster WARNING LIGHTS AND CHIMES Base instrument cluster with standard measure shown; metric similar 160 180 200 20 0 km/h Optional instrument cluster with standard measure shown; metric similar 100 120 180 200 20 0 km/h Warning lights can alert you to a vehicle condition that may become serious enough to cause extensive repairs.
Page 15: Instrument Cluster
Instrument Cluster Many lights will illuminate when you start your vehicle to make sure the indicators work. If any light remains on after starting the vehicle, refer to the respective system warning light for additional information. Note: Some warning lights are reconfigurable telltale (RTT) indicators. These indicators display in the lower line of the message center near the odometer reading.
Page 16 Instrument Cluster Brake system warning light: To confirm the brake system warning light is functional, it will BRAKE momentarily illuminate when the ignition is turned to the on position when the engine is not running, or in a position between on and start, or by applying the parking brake when the ignition is turned to the on position.
Page 17 Instrument Cluster Charging system (RTT): Illuminates when the battery is not charging properly. If it stays on while the engine is running, there may be a malfunction with the charging system. Contact your authorized dealer as soon as possible. This indicates a problem with the electrical system or a related component.
Page 18 Instrument Cluster Engine coolant temperature (RTT): Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as possible, switch off the engine and let cool. Refer to Engine coolant in the Maintenance and Specifications chapter. WARNING: Never remove the coolant reservoir cap while the engine is running or hot.
Page 19 Instrument Cluster Liftgate ajar (RTT): Displays when the ignition is in the on position and the trunk is open. Low washer fluid (RTT): Illuminates when the windshield washer fluid is low. Turn signal: Illuminates when the left or right turn signal or the hazard lights are turned on.
Page 20 Instrument Cluster Hill descent (RTT) (if equipped): Illuminates when hill descent is turned on. Heads up display (if equipped): A red beam of lights will illuminate on the windshield in certain instances when using adaptive cruise control and/or the collision warning system.
Page 21: Gauges
Instrument Cluster GAUGES Base cluster Shown in standard measure. Metric similar. 160 180 200 20 0 km/h 1. Tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. 2.
Page 22 Instrument Cluster • Engine coolant temperature gauge (if enabled): Indicates engine coolant temperature. At normal operating temperature, the level indicator will be in the normal range. The indicator will change colors indicating blue for cool, gray for normal and red for hot.
Page 23: Message Center
BASE MESSAGE CENTER (IF EQUIPPED) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that may take their focus off the road. Your primary responsibility is the safe operation of the vehicle.
Page 24 Instrument Cluster Your vehicle’s message center is capable of monitoring many vehicle systems and will alert you to potential vehicle problems and various conditions with informational messages and/or warnings. The message center is also used to program/configure the different features of your vehicle. The message center display is located in the instrument cluster.
Page 25 Instrument Cluster Press and hold OK to reset the current trip, distance time, average MPG, and fuel used. Scroll up/down to highlight one of the options, then press the right arrow key or OK to enter into that menu option. Note: Some items are optional and may not appear.
Page 26 Instrument Cluster Settings (cont’d) Convenience Easy Entry/Exit (cont’d) Locks Autolock Autounlock Remote Unlock All Doors or Driver First Oil life Reset Set 10-100% Power Liftgate Switch Enabled or Disabled Remote Start Climate Control Heater – A/C Auto or Last Setting Climate Control Front Defrost Auto or Off...
Page 27 Instrument Cluster Settings (cont’d) MyKey Create MyKey Hold OK to Create MyKey Traction Control Always On or User Selectable Max Speed 80 MPH (130 km/h) or Off Speed Warning 45 mph (75 km/h), 55 mph (90 km/h), 65 mph (105 km/h) or Volume Limiter Clear MyKeys Hold OK to Clear MyKeys...
Page 28 Instrument Cluster Types of messages and warnings: • Some messages will appear briefly to inform you of something you may need to take action on or be informed of. • Some messages will appear once and then again when the vehicle is restarted.
Page 29 Instrument Cluster CHANGE ENGINE OIL SOON — Displayed when the engine oil life remaining is 10% or less. OIL CHANGE REQUIRED — Displayed when the oil life left reaches ENGINE COOLANT OVER TEMP — Displayed when the engine coolant temperature is excessively high. WASHER FLUID LEVEL LOW —...
Page 30 Instrument Cluster LOW ENGINE OIL PRESSURE — Stop the vehicle as soon as safely possible, turn off the engine. Check the oil level. See Checking the engine oil in the Maintenance and Specifications chapter. If the warning stays on or continues to come on with your engine running, contact your authorized dealer as soon as possible.
Page 31 Instrument Cluster SERVICE POWER STEERING — The power steering system has detected a condition that requires service. SERVICE POWER STEERING NOW — The power steering system has detected a condition within the power steering system that requires service immediately. ACCESSORY POWER ACTIVE (if equipped) — Displayed when the vehicle is in the accessory ignition state on keyless vehicles.
Page 32 Instrument Cluster RESTART NOW OR KEY IS NEEDED (if equipped) — Displayed when the start/stop button is pressed to shut off the engine and a Intelligent Access Key is not detected inside the vehicle. Refer to Push button start system in the Driving chapter for more information. SPEED LIMITED TO 130 KM/H —...
Page 33 Instrument Cluster VEHICLE COMING FROM RIGHT (if equipped) — Displayed when the blind spot information system with cross traffic alert (CTA) system is operating and senses a vehicle. See Blind Spot Information System (BLIS ) with Cross Traffic Alert in the Driving chapter. ACTIVE PARK FAULT (if equipped) —...
Page 34 Instrument Cluster TERRAIN MANAGEMENT MUD, RUT MODE (if equipped) — Displays driver selected terrain management mode. TERRAIN MANAGEMENT NORMAL MODE (if equipped) — Displays driver selected terrain management mode. TERRAIN MANAGEMENT SAND MODE (if equipped) — Displays driver selected terrain management mode. TERRAIN MANAGEMENT SNOW MODE (if equipped) —...
Page 35 Instrument Cluster • Press the up/down arrow buttons to move up/down through the message center choices. • Press the left/right arrow buttons km/h to move left/right through the message center choices. • Press the OK button to select highlighted options and confirm choices/messages.
Page 36 Instrument Cluster To change the Menu Control between Standard or Memory On, refer to Vehicle and Menu Control found in the table under the Settings section later in this chapter. Display Mode Press the right arrow on the left steering wheel mounted button when display mode is selected.
Page 37 Instrument Cluster Round analog tachometer + Fuel gauge For descriptions of the tachometer and fuel gauge, see the description listed previously. Round analog tachometer + Fuel gauge + Engine coolant temperature gauge For descriptions of the tachometer and fuel gauge, see the description listed previously.
Page 38 Instrument Cluster indicate that there are multiple screens that you can navigate through. Each press of the right arrow will navigate to the next screen until the last screen is reached. The white highlighted box indicates which of the screens you are currently viewing: Choose the standard or enhanced display.
Page 39 Instrument Cluster Fuel Economy Press the right arrow on the left steering wheel mounted button when fuel economy is selected. The boxes in the upper right corner of the screen indicate that there are multiple screens that you can navigate through.
Page 40 Instrument Cluster To determine your average highway fuel economy, do the following: 1. Drive the vehicle at least 5 miles (8 km) with the speed control system engaged to display a stabilized average. 2. Record the highway fuel economy for future reference. It is important to reset fuel economy after setting the speed control to get accurate highway fuel economy readings.
Page 41 Instrument Cluster Vehicle Power Liftgate Enable / Disable Climate Control Heater – A/C Auto / Last (using this Settings feature allows Front Defrost Auto / Off you to select different climate Rear Defrost Auto / Off control modes when the vehicle Remote Start Driver Seat Auto / Off...
Page 42 Instrument Cluster Units Distance Miles & Gal / Km & Liters Temperature Fahrenheit (°F) / Celsius (°C) Restore defaults Hold OK to Restore Settings to Factory Defaults Information In this mode, you can view different vehicle system information and perform a system check. When Press OK for info is displayed, pressing OK will give you information on the currently selected/displayed options.
Page 43 Instrument Cluster In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for four seconds. The message center will display the last selected feature if there are no more warning messages.
Page 44 Instrument Cluster PARK BRAKE ENGAGED — Displayed when the parking brake is set, the engine is running and the vehicle is driven more than 3 mph (5 km/h). If the warning stays on after the parking brake is released, contact your authorized dealer as soon as possible. CHECK CHARGING SYSTEM —...
Page 45 Instrument Cluster warning stays on or continues to come on with your engine running, contact your authorized dealer as soon as possible. OIL CHANGE REQUIRED — Displayed when the oil life left reaches WASHER FLUID LEVEL LOW — Indicates the washer fluid reservoir is less than one quarter full.
Page 46 Instrument Cluster AWD OFF (if equipped) — Displayed when the 4WD system has been automatically disabled to protect itself. This is caused by operating the vehicle with the compact spare tire installed or if the system is overheating. The 4WD system will resume normal function and clear this message after driving a short distance with the road tire re-installed or after the system is allowed to cool.
Page 47 Instrument Cluster OFF ROAD MODE ENABLED (if equipped) — Displayed when off road mode becomes active. TERRAIN MANAGEMENT MUD, RUT MODE (if equipped) — Displays driver selected terrain management mode. TERRAIN MANAGEMENT NORMAL MODE (if equipped) — Displays driver selected terrain management mode. TERRAIN MANAGEMENT SAND MODE (if equipped) —...
Page 48 Instrument Cluster NO KEY DETECTED (if equipped) — Displayed if the Intelligent Access Key is not detected by the system in the following three scenarios: • When the start/stop button is pressed in an attempt to either start the engine or cycle through the ignition states. •...
Page 49 Instrument Cluster ADAPTIVE CRUISE NOT AVAILABLE SENSOR BLOCKED SEE MANUAL (if equipped) — Displayed when the radar is blocked because of poor radar visibility due to bad weather or ice/mud/water in front of radar. Driver can typically clean the sensor to resolve. COLLISION WARN NOT AVAILABLE (if equipped) —...
Page 50 Instrument Cluster ACTIVE PARK FAULT (if equipped) — Displayed when a fault has occurred with the active park assist system. Refer to Active park assist in the Driving chapter for more information. CHECK REAR PARK AID (if equipped) — Displayed when the transmission is in R (Reverse) and the park aid is disabled.
Page 51: Entertainment Systems
MYFORD™ SYSTEM (IF EQUIPPED) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that may take their focus off the road. Your primary responsibility is the safe operation of the vehicle.
Page 52 Entertainment Systems 2. You can press some of the hard buttons to access their respective menus. 3. Use the center control in the same manner you would a joystick — press to move up/down in menus or press to move out of or into a menu.
Page 53 Entertainment Systems • Select the Direct or Tune soft key then scroll through the frequencies by using or the tune knob. • Select the Mute soft key to mute the playing media. Press again to return to the playing media. •...
Page 54 Entertainment Systems • Set Category: Select to choose a specific music category in FM mode. You can then search for stations only playing this kind of music.Note: RBDS/RDS text must be turn on before “Set Category” will appear. • RBDS/RDS Text: Select to turn Radio Broadcast Digital Signal text on to view additional broadcast data.Note: This feature defaults to off, but it must be turned on in order for you to choose and set a category.
Page 55 Entertainment Systems • To view your presets, press for a list of your saved presets. The display will indicate the preset # that to which the station was saved. • Select the ‘Replay’ soft key to replay audio on the current channel. You can replay approximately 45 minutes of audio as long as you have remained tuned to the current station.
Page 56 Entertainment Systems • Set Category: Select to scroll through a list of available SIRIUS channel categories (Pop, Rock, News, etc.) Note: If you select a category, the seek and scan functions will only stop on channels in that category. • Alerts: Select this to create an alert for a particular song or artist or team.
Page 57 Note: SIRIUS reserves the unrestricted right to change, rearrange, add or delete programming including canceling, moving or adding particular channels, and its prices, at any time, with or without notice to you. Ford Motor Company shall not be responsible for any such programming changes.
Page 58 Entertainment Systems Radio Display Condition Possible action No Signal Loss of signal from The signal is currently the SIRIUS satellite being blocked. When or SIRIUS tower to you move into an open the vehicle antenna. area, the signal should return. Updating Update of channel No action required.
Page 59 (12 cm) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Do not use any irregular shaped CDs or discs with a scratch protection film attached. CDs with...
Page 60: Auxiliary Input Jack (Line In)
Auxiliary input jack (line in) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that may take their focus off the road. Your primary responsibility is the safe operation of the vehicle.
Page 61 MYFORD TOUCH™ (IF EQUIPPED) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that may take their focus off the road. Your primary responsibility is the safe operation of the vehicle.
Page 62: Climate Controls
Climate Controls SINGLE ZONE MANUAL SYSTEM WITH REAR CLIMATE CONTROLS (IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius: Press MENU > Display Settings > Temp. Setting, or refer to Settings in the Message Center section of the Instrument Cluster chapter. (Fan speed adjustment): Turn to select the desired fan speed.
Page 63 Climate Controls • : Distributes air through the instrument panel vents. • : Distributes air through the instrument panel vents, demister vents, floor vents and rear seat floor vents. • : Distributes air through the demister vents, floor vents and rear seat floor vents.
Page 64 Climate Controls • To reduce humidity build-up inside the vehicle, do not drive with the system off or with (recirculated air) engaged and A/C off. • Do not put objects under the front seats that will interfere with the airflow to the back seats. •...
Page 65: Automatic Temperature Control
Climate Controls AUTOMATIC TEMPERATURE CONTROL SYSTEMS Dual Automatic Temperature Control (DATC) Sony system (if equipped) Note: Your climate control system is touch sensitive. You need only lightly touch the control graphic to activate the feature. Note: Your vehicle is also equipped with touchscreen climate control features.
Page 66 Climate Controls automatically when MAX A/C is selected or can be engaged manually in any airflow mode except (defrost). Recirculated air may turn off automatically in all airflow modes except MAX A/C to reduce fog potential. 4. DUAL: Press to activate dual zone (separate passenger temperature control).
Page 67 Climate Controls Dual Automatic Temperature Control (DATC) system with MyTemp (if equipped) Note: Your climate control system is touch sensitive. You need only lightly touch the control graphic to activate the feature. Note: Your vehicle is also equipped with touchscreen climate control features.
Page 68 Climate Controls 3. MAX A/C: Distributes recirculated air through the instrument panel vents to cool the vehicle. This re-cooling of the interior air is more economical and efficient. Recirculated air may also help reduce undesirable odors from entering the vehicle. Touch MAX A/C again for normal A/C operation.
Page 69: Automatic Operation
Climate Controls Operating tips • To reduce fog build-up on the windshield during humid weather, select (defrost) or (floor/defrost). • To reduce humidity build-up inside the vehicle, do not drive with the system off or with (recirculated air) engaged and A/C off. •...
Page 70: Touchscreen Features
Climate Controls Touchscreen features (if equipped) Press the lower right corner on the touchscreen to access these features. (Power): Press to activate/deactivate the climate control system. When the system is off, outside air is prevented from entering the vehicle through the vents. 2.
Page 71 Climate Controls 6. A/C: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency. Engages automatically in MAX A/C, (defrost) and (floor/defrost). 7. AUTO: Press to engage full automatic operation. Select the desired temperature using the temperature control. The system will automatically determine fan speed, airflow distribution, A/C on or off, and outside or recirculated air, to heat or cool the vehicle in order to reach the desired temperature.
Page 72 Climate Controls Rear controls To access, press ‘Rear’ in the lower right status bar. When the arrow icon is down ( ), you have access to the rear controls and they will display along on the bottom of the screen under the Rear Climate heading.
Page 73: Rear Window Defroster
Climate Controls • Fan Increase • Fan Decrease •Temperature • Temperature Increase • Temperature <15.5–29.5> • Temperature Decrease degrees • Temperature <60–85> degrees • My Temp • Help *Note: If you have said “Temperature”, you can then say any of the following commands: •...
Page 74 Climate Controls The defroster turns off automatically after 10 minutes or when the ignition is turned to off or the accessory position. To manually turn off the defroster before 10 minutes have passed, push the control again. REMOTE START CLIMATE OPERATION (IF EQUIPPED) The climate control system will condition the cabin temperature during remote start.
Page 75 Climate Controls Note: A cabin air filter must be installed at all times to prevent foreign objects from entering the system. Running the system without a filter in place could result in degradation or damage to the system. For replacement intervals, refer to the Scheduled Maintenance chapter. For more information regarding your filter, see your authorized dealer.
Page 76: Lights
Lights HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps. Turns the headlamps on. Autolamp control (if equipped) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.
Page 77 Lights 3. Rotate the headlamp control to the off position. 4. Turn the vehicle on. 5. Turn the vehicle off. 6. Turn the headlamp control to the autolamp position (the headlights should turn on). 7. Turn the headlamp control to the off position when the desired delay time (up to three minutes) has been reached.
Page 78 Lights Daytime running lamps (DRL) (if equipped) To activate DRL: • the ignition must be in the on position and • the headlamp control is in the position • the transmission is not in P (Park). WARNING: Always remember to turn on your headlamps at dusk or during inclement weather.
Page 79 Lights Dome lamp control Use to manually turn the dome lamp • Press the control. This will turn on the interior courtesy lights. The lights will remain on until the control is pressed again. Dome lamp control (with fog lamps) Use to manually turn the dome lamp •...
Page 80 Lights • (1) 8 feet (2.4 m) • (2) Center height of lamp to ground • (3) 25 feet (7.6 m) • (4) Horizontal reference line 2. The center of the headlamp has a 3.0 mm circle on the lens. Measure the height from the center of your headlamp to the ground (2) and mark an 8 foot (2.4 m) long...
Page 81: Turn Signal Control
Lights 5. Locate the vertical adjuster for each headlamp. Using a Phillips #2 screwdriver, turn the adjuster control either clockwise (to adjust down) or counterclockwise (to adjust up). Note: HORIZONTAL AIMING IS NOT REQUIRED FOR THIS VEHICLE AND IS NON-ADJUSTABLE. TURN SIGNAL CONTROL The turn signal lever does not mechanically lock in the upward or downward position when activated.
Page 82 Lights INTERIOR LAMPS Front row map lamps (if equipped) To turn on the map lamps, press the outer edge of the clear lens. The front row map lamp lights when: • any door is opened. • the instrument panel dimmer button is pressed until the courtesy lamp comes on.
Page 83: Bulb Replacement
Lights Third row cargo lamp The dome lamp lights when: • any door is opened. • the instrument panel dimmer button is pressed until the courtesy lamp comes on. • any of the remote entry controls are pressed and the ignition is off.
Page 84 Lights Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America and an “E” for Europe to ensure lamp performance, light brightness and pattern and safe visibility. Using incorrect bulbs may damage the lamp assembly or void the lamp assembly warranty or may not provide quality bulb burn time.
Page 85 Lights Replacing headlamp bulbs 1. Make sure that the headlamp control is in the off position. 2. Open the hood. 3. Remove the bulb cover. 4. Turn the bulb holder counterclockwise and remove it. 5. Disconnect the electrical connector. WARNING: Handle a halogen headlamp bulb carefully and keep out of children’s reach.
Page 86 Lights Replacing front parking lamp/turn signal bulbs 1. Make sure that the headlamp control is in the off position. 2. Open the hood. 3. Remove the hood overslam bumper tower to service park/turn bulb (if needed). 4. Rotate the bulb socket counterclockwise and remove it from the lamp assembly.
Page 87 Lights Reverse steps to reinstall bulb(s). Replacing sidemarker bulbs 1. Make sure that the headlamp control is in the off position. 2. Open the hood. 3. Remove the hood overslam bumper tower to service sidemarker bulb (if needed). 4. Rotate the bulb socket counterclockwise and remove it from the lamp assembly.
Page 88 Lights 5. Pull the bulb straight out of the socket. Reverse steps to reinstall bulb(s). Replacing turn/backup lamp bulbs The turn/backup lamp bulbs are located in the same area of the tail lamp assembly, one below the other. Follow the same steps to replace these bulbs: 1.
Page 89 Lights 5. Disconnect the electrical connector (1) from the lamp assembly. Disconnect the bulb socket (2) from the lamp assembly by squeezing the two tabs at the top and bottom of the socket. 6. Pull bulb straight out of socket and install the new bulb. 7.
Page 90 Lights Replacing license plate lamp bulbs 1. Make sure the headlamp switch is off. 2. Remove the lamp assembly by pressing the small tab and rocking the lamp assembly out. 3. Remove the bulb socket from the lamp assembly by turning counterclockwise and pull the bulb straight out.
Page 91: Driver Controls
Driver Controls WINDSHIELD WIPERS Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. Speed dependent wipers (if equipped): When the wiper control is set to any of the interval settings except the longest pause setting, the pause time between wiping will automatically adjust with the vehicle speed.
Page 92 Driver Controls Windshield washer: Press the end of the stalk: • briefly: causes the wipers to swipe three times with washer fluid. • a long press and hold: the wipers and washer fluid will be activated for up to ten seconds. Mist wipe: Press the stalk down and release for a single swipe of the wipers without washer fluid.
Page 93 Driver Controls From either position, the control will automatically return to the 2 or O (off) position. Reverse wiper feature: The rear wiper will be automatically activated in an intermittent setting when shifting into R (Reverse) if the front wipers are activated. This feature may be enabled/disabled through the message center.
Page 94 Driver Controls Slide-on-rod feature Rotate the visor towards the side window and extend it rearward for additional sunlight coverage. Note: To stow the visor back into the headliner, visor must be retracted before moving it back towards the windshield. OVERHEAD CONSOLE The appearance of your vehicle’s overhead console will vary according to your option package.
Page 95 Driver Controls • Cupholders • Large utility storage compartment with 12V power point • 12V power point and 110V AC power point outlet on the rear of the console • Auxiliary AV connections, USB ports and 12V power point located forward of the shifter WARNING: Use only soft cups in the cupholder.
Page 96 Driver Controls • In the cargo area Do not use the power point for operating the cigarette lighter element (if equipped). Note: Do not plug optional electrical accessories into the cigarette lighter socket (if equipped). Improper use of the lighter can cause damage not covered by your warranty, and can result in fire or serious injury.
Page 97: Power Windows
Driver Controls • Motor loads, such as vacuum cleaners, electric saws and other electric power tools, compressor-driven refrigerators, etc. • Measuring devices, which process precise data, such as medical equipment, measuring equipment, etc. • Other appliances requiring an extremely stable power supply: microcomputer-controlled electric blankets, touch sensor lamps, etc.
Page 98 Driver Controls WARNING: When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. Press and pull the window switches to open and close windows. •...
Page 99: Mirrors
Driver Controls Security override To override a bounce-back condition, within two seconds after the window reaches the bounce-back position, pull and hold the switch up and the window will travel up with no bounce-back or pinch protection. If the switch is released before the window is fully closed, the window will stop.
Page 100 Driver Controls Note: A rear center passenger and/or raised rear center headrest (if equipped) may also block the light from reaching the sensor. Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products. EXTERIOR MIRRORS Power side view mirrors WARNING: Do not adjust the mirror while the vehicle is in...
Page 101 Driver Controls Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products. Fold-away mirrors Fold the side mirrors in carefully before driving through a narrow space, like an automatic car wash. Powerfold mirrors (if equipped) You can fold the side mirrors simultaneously using the power...
Page 102: Speed Control
Driver Controls POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. The control is located on the left side of the steering column. Press and hold the rear of the control to move the pedals toward you.
Page 103 Driver Controls SET: Press to set a speed or to increase or decrease the set speed. RES (Resume): Press to resume the set speed. CNCL (Cancel): Press to cancel the set speed. ON/OFF: Press to turn speed control on or off. Setting speed control To set speed control: 1.
Page 104: Adaptive Cruise Control
Driver Controls • Use the accelerator pedal to get to the desired speed then press SET upward and release. Reducing speed while using speed control To reduce a set speed: • Press SET downward and hold until you get to the desired speed, then release.
Page 105 Driver Controls WARNING: Adaptive cruise control is not a collision warning or avoidance system. Additionally, adaptive cruise control will not detect: • Stationary or slow moving vehicles below 6 mph (10 km/h). • Pedestrians or objects in the roadway. • Oncoming vehicles in the same lane. WARNING: Do not use the adaptive cruise control when entering or leaving a highway, in heavy traffic or on roads that are winding, slippery or unpaved.
Page 106 Driver Controls Setting adaptive cruise control 1. Press and release ON. The message center will display the gray ACC indicator light, current gap setting and SET. 2. Accelerate to the desired speed. 3. Press SET upward and release. The vehicle speed will be stored in the memory and the message center will display a green ACC indicator light, current gap setting and desired set speed.
Page 107 Driver Controls braking which is applied by the ACC system is limited and can be overridden by the driver applying the brakes. If the ACC system predicts that its maximum braking level will not be sufficient, an audible warning will sound while the ACC continues to brake.
Page 108 Driver Controls Disengaging adaptive cruise control Press the brake pedal or press CNCL to disengage the adaptive cruise control. The last set speed will be displayed with a strikethrough. Disengaging the adaptive cruise control will not erase your previous set speed.
Page 109 Driver Controls Hilly condition usage It is recommended that the driver select a lower gear position when ACC is active in situations such as prolonged downhill driving on steep grades (i.e., driving in mountainous areas). In these situations, additional engine braking is needed to reduce the load on the vehicle’s regular brake system to prevent them from overheating.
Page 110 Driver Controls • With vehicles that edge into your lane. These vehicles can only be detected once they have moved fully into your lane. • There may be issues with the detection of vehicles in front when driving into and coming out of a bend or curve in the road. In these cases ACC may brake late or unexpectedly.
Page 111 Driver Controls • A failure has occurred in the ACC system or related system. Blocked sensor If a message regarding a blocked sensor is displayed, the radar signals from the sensor have been obstructed. The sensor is located behind a fascia cover near the driver side of the lower grille.
Page 112 Driver Controls WARNING: Do not use ACC when towing a trailer with brake controls. Aftermarket trailer brakes will not function properly when ACC is activated because the brakes are electronically controlled. Failing to do so may result in loss of vehicle control, which could result in serious injury.
Page 113: Moon Roof
Driver Controls Navigation/SYNC system hands-free control features (if equipped) Press to active the voice recognition feature. Refer to Voice recognition feature in the MyFord Touch™ / MyLincoln Touch™ supplement. Press to access phone features. Refer to Phone features in the MyFord Touch™...
Page 114 Driver Controls WARNING: Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt themselves. The dual panel moon roof and power sunscreen are equipped with an automatic, one-touch, express opening and closing feature. To stop motion at any time during the one-touch operation, press the control a second time.
Page 115 Driver Controls roof will close without the bounce-back function active. For example: Bounce-back override can be used to overcome the resistance of ice on the moon roof or seals. To vent the dual panel moon roof: Press and quickly release the TILT control (moon roof is equipped with, automatic, one-touch, tilt open feature).
Page 116 Driver Controls programmed Car2U system buttons should be erased for security reasons. Refer to Erasing the Car2U Home Automation System buttons later in this section. Read the instructions completely before attempting to program the Car2U system. Because of the steps involved, it may be helpful to have another person assist you in programming the transmitter.
Page 117 Driver Controls Rolling code programming Note: Programming the rolling code garage door opener involves time-sensitive actions. Read the entire procedure prior to beginning so you will know which actions are time-sensitive. If you do not follow the time-sensitive actions, the device will time out and you will have to repeat the procedure.
Page 118 Driver Controls 3. Return to your vehicle. Press and hold the Car2U system button you would like to use to control the garage door. You may need to hold the button from 5–20 seconds, during which time the selected button indicator light will blink slowly.
Page 119 Driver Controls 1. To program units with fixed code DIP switches, you will need the garage door hand-held transmitter, paper and a pen or pencil. 2. Open the battery cover and record the switch settings from left to right for all 8 to 12 switches. Use the figure below: When a switch is in the up, on, or + position, circle “L.”...
Page 120 Driver Controls 5. Press and hold the Car2U system button you would like to use to control the garage door. Immediately (within 1 second) release the button once the garage door moves. During this time the selected button indicator light will blink slowly.
Page 121 Driver Controls FCC and RSS-210 Industry Canada Compliance The Car2U system complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received including interference that may cause undesired operation.
Page 122 Driver Controls CARGO AREA FEATURES Cargo net (if equipped) The cargo net secures lightweight objects in the cargo area. Attach the net to the loops and anchors provided. WARNING: This net is not designed to restrain objects during a collision. 2011 Explorer (exp) Owners Guide, 3rd Printing USA (fus)
Page 123 Driver Controls Utility hook The utility hook can be used to hang small items such as grocery bags, etc. Do not hang more than 10 lb (4.5 kg) on the hook. MANUAL LIFTGATE (IF EQUIPPED) The liftgate area is only intended for cargo, not passengers. To open the liftgate, press the button located in the top of the liftgate pull cup handle to unlatch...
Page 124 Driver Controls WARNING: Make sure that the liftgate is closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate door open, keep the vehicle well ventilated so outside air comes into the vehicle.
Page 125 Driver Controls failure. If any excessive load is removed and you still have a faster chime, have the system serviced immediately by your authorized dealer. Do not attempt to manually force the liftgate to travel faster than the power system will permit. This will activate the obstacle detection feature.
Page 126 Driver Controls To power open the liftgate with outside liftgate control button: 1. Unlock the liftgate with the transmitter or power door unlock control. If the intelligent access transmitter (if equipped) is within 3 feet (1 meter) of the liftgate, the liftgate will unlock when you press the liftgate release button.
Page 127 Driver Controls The new open liftgate height will now be recalled when the power liftgate is opened. To change the programmed height, repeat the above procedure. Once the power liftgate is opened it can be manually moved to a different height. Note: Do not drive with the liftgate open without first disabling the power function and securing the liftgate to the vehicle.
Page 128 Your vehicle may be equipped with factory-installed crossbars. Ford Genuine Accessory crossbars, designed specifically for your vehicle, are also recommended for use with your roof rack system.
Page 129 Driver Controls 3. Tighten the tie-down hooks at both sides of the crossbar by turning clockwise until tight. (A small screwdriver or similar tool can be used to tighten the hook an additional half turn.) Be sure to check that the tie-down hooks are tight each time load is added or removed from the roof rack, and periodically while traveling.
Page 130: Locks And Security
Locks and Security KEYS Integrated keyhead transmitters (IKTs) (if equipped) Your vehicle may be equipped with two integrated keyhead transmitters (IKTs). The key blade functions as a programmed key which starts the vehicle and unlocks/locks the driver’s door. The transmitter portion functions as the remote entry transmitter.
Page 131 Locks and Security The IA key also contains a removable mechanical key blade that can be used to unlock the driver door. To release the mechanical key blade, slide the release on the back of the transmitter and pull the blade out. Your IA keys are programmed to your vehicle.
Page 132 Locks and Security • If equipped, any of the following: parking aid, blind spot information system (BLIS™) with cross traffic alert and forward collision warning systems cannot be turned off. Optional settings – these settings can be changed • Vehicle speed is limited to 80 mph (130 km/h). Visual warnings are displayed followed by a chime when the vehicle speed has reached 80 mph (130 km/h).
Page 133 If you choose to install a remote start system please see your authorized dealer for a Ford-approved remote start system. The following information MAY help customers who choose to use a non Ford-approved remote start system. The actions provided below do NOT 2011 Explorer (exp) Owners Guide, 3rd Printing...
Page 134 Ford-approved remote start system as a MyKey if the remote start fob is used by the MyKey driver. To program a non Ford-approved remote start system as MyKey , do the following: 1. Enter the vehicle and close all doors.
Page 135 Locks and Security 1. Enter the vehicle, close all doors. 2. Remote start the vehicle using your non Ford-approved remote start fob. 3. Follow Steps 1-4 in the Clear MyKey section. Troubleshooting Condition Potential Causes • Key in the ignition is already a Can’t create a MyKey...
Page 136 • For programming spare keys, refer Lost any key to the Programming spare keys section in this chapter. • Vehicle has a non Ford-approved I accidentally programmed all keys as MyKeys remote start system that is recognized as an admin key. Refer to the Using...
Page 137: Locks
• MyKey system has been recently cleared. • Vehicles has been remote started using a non Ford-approved remote start system (as if an admin key) then a MyKey is inserted without recycling the MyKey in ignition. POWER DOOR LOCKS •...
Page 138 Locks and Security When you open one of the front doors and you lock the vehicle with the power door lock control (on the driver or passenger door trim panel), all the doors will lock, then all doors will automatically unlock reminding you that your key is still in the ignition.
Page 139 Locks and Security The autolock feature repeats when: • any door is opened then closed while the ignition is on and the vehicle speed is 9 mph (15 km/h) or lower, and • the vehicle then attains a speed greater than 12 mph (20 km/h). Deactivating/activating autolock feature Your vehicle comes with the autolock features activated;...
Page 140 Locks and Security Autounlock feature (if enabled) The autounlock feature will unlock all the doors when: • the ignition is on, all the doors are closed, and the vehicle has been in motion at a speed greater than 12 mph (20 km/h); •...
Page 141 Locks and Security 6. To enable/disable the autounlock feature, press the lock control, then press the unlock control. The horn will chirp once if autounlock was deactivated or twice (one short and one long chirp) if autounlock was activated. 7. Turn the ignition off. The horn will chirp once to confirm the procedure is complete.
Page 142 Locks and Security The typical operating range for your transmitter is approximately 33 feet (10 meters) unless equipped with remote start, which allows for greater range performance. A decrease in operating range could be caused by: • weather conditions, • nearby radio towers, •...
Page 143 Locks and Security Your vehicle will allow you to unlock and enter your vehicle without actively using a key or transmitter. You can use the intelligent access feature at the front doors or at the liftgate. You can activate the intelligent access feature as long as you have one of your IA keys within range of the front doors or the liftgate.
Page 144 Locks and Security 2. Press and release again within three seconds to confirm that all the doors are closed. Note: The doors will lock again, the horn will chirp and the turn lamps will illuminate if all the doors and liftgate are closed. Note: If any door or the liftgate is not closed, or if the hood is not closed on vehicles equipped with a perimeter alarm or remote start, the horn will chirp twice and the lamps will not flash.
Page 145 Locks and Security Press to automatically move the seat, power mirrors and adjustable foot pedals (if equipped) to the desired memory position. The mirrors will move to the programmed position and the seat will move to the easy entry position. The seat will move to the final position when the ignition is switched out of off (if easy entry feature is enabled).
Page 146 Locks and Security To replace the battery: Integrated keyhead transmitter (IKT) 1. Twist a thin coin in the slot near the key ring to remove the battery cover (1). Note: Do not wipe off any grease on the battery terminals on the back surface of the circuit board.
Page 147 Locks and Security 2. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 3. Insert the new battery. Refer to the instructions inside the IA key for the correct orientation of the battery. Press the battery down to ensure that the battery is fully seated in the battery housing cavity.
Page 148 Locks and Security Illuminated exit When all vehicle doors are closed, the ignition is turned off and the key is removed from the ignition (IKT only), the interior dome lamps, parking lamps and the puddle lamps (if equipped) will illuminate. The lamps will turn off if all the doors remain closed and •...
Page 149 Locks and Security Vehicles with automatic climate control can be configured to operate when the vehicle is started. Refer to Remote start climate options in the Climate Controls chapter for more information and also refer to Message center in the Instrument Cluster chapter to learn how to enable different climate options.
Page 150 Locks and Security 1. Press to lock all the doors. 2. Press two times. The exterior lamps will flash twice. If for some reason, the system fails to start, the horn will chirp. Note: If the vehicle has been remote started and is equipped with an IKT, you must turn the ignition on before driving the vehicle.
Page 151 Locks and Security SECURICODE™ KEYLESS ENTRY SYSTEM (IF EQUIPPED) You can use the keyless entry keypad to: • lock or unlock the doors without using a key. • recall memory seat/power mirrors positions (if equipped). • enable/disable autolock and autounlock. •...
Page 152 Locks and Security Tips: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. • The factory set code will work even if you have set your own personal code.
Page 153: Anti-Theft System
Note: The SecuriLock passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the same key chain may cause vehicle starting issues.
Page 154 Locks and Security The integrated keyhead transmitter (IKT) functions as both a programmed ignition key that operates all the locks and starts the vehicle, as well as a remote keyless entry transmitter. A maximum of eight coded keys can be programmed to your vehicle; only four of these eight coded keys can be IKTs with remote entry functionality.
Page 155 Locks and Security Please read and understand the entire procedure before you begin. 1. Insert the first previously programmed coded key into the ignition. 2. Turn the ignition from off to on. Keep the ignition on for at least three seconds, but no more than 10 seconds.
Page 156 Locks and Security accessible. If two previously programmed keys are not available, you must take your vehicle to your authorized dealer to have the spare key(s) programmed. Note: A maximum of four intelligent access keys can be programmed to your vehicle. If you would like to replace a previously programmed access key with a new access key, or if you already have four access keys programmed to your vehicle, you must take your vehicle and all access keys to your authorized dealer to be erased and reprogrammed.
Page 157 Locks and Security Note: To program MyKey features, refer to MyKey in this chapter. PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter alarm system will warn you in case of unauthorized entry to your vehicle. When the following types of unauthorized entry occur: •...
Page 158 Locks and Security Disarming the system To disarm the system, do any of the following: • Pressing the power door unlock control within the 20-second, pre-armed mode will disarm the system. • Unlock the doors by pressing unlock on the remote entry transmitter.
Page 159: Seating And Safety Restraints
Seating and Safety Restraints FRONT SEATS WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.
Page 160 Seating and Safety Restraints The adjustable head restraints consist of: • a trimmed energy absorbing foam and structure (1), • two steel stems (2), • a guide sleeve adjust/release button (3), • and a guide sleeve unlock/remove button (4). To adjust the head restraint, do the following: 1.
Page 161 Seating and Safety Restraints WARNING: To minimize the risk of neck injury in the event of a crash, head restraints must be installed properly. Tilting head restraints (if equipped) The front head restraints may have a tilting feature for extra comfort. To tilt the head restraint, do the following: 1.
Page 162 Seating and Safety Restraints Pull lever up to adjust seatback. WARNING: Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched.
Page 163 Seating and Safety Restraints WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. WARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting in serious injury or death in a crash.
Page 164 Seating and Safety Restraints • Move the control in the directions shown to move the seat forward or backward. • Press the control to recline the seatback forward or rearward. Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press the forward side of the control to adjust firmness.
Page 165 Seating and Safety Restraints WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater. The seat heater may cause burns even at low temperatures, especially if used for long periods of time.
Page 166 Seating and Safety Restraints Note: Do not do the following: • Place heavy objects on the seat • Operate the seat heater if water or any other liquid is spilled on the seat. Allow the seat to dry thoroughly. To operate the heated seats: Press the heated seat symbol to cycle through the various heat settings and off.
Page 167 Seating and Safety Restraints • There is a filter located under each front seat. • The filter can be accessed from the rear of the seat. Move the front seat to full up to ease access. To remove an air filter: 1.
Page 168 Seating and Safety Restraints To install a filter: 1. First, position the filter in its housing making sure that the far forward end is all the way up in the housing. 2. Push in on the center of the outside edge of the filter and rotate up into the housing until it clips into position.
Page 169 Seating and Safety Restraints Memory profiles The memory feature also coordinates with user-created profile settings utilizing the infotainment touchscreen system (if equipped). See the Creating a user profile section in the MyFord Touch supplement for more information. Easy entry/exit feature (if equipped) This feature automatically moves the driver’s seat rearward 2 in.
Page 170 Seating and Safety Restraints To fold the outboard head restraint, pull the release strap. To remove the outboard head restraint, start with it folded and then press and hold both release buttons and pull it upwards. • Center seat head restraint (if equipped)– The center head restraint is vertically adjustable and can also be removed.
Page 171 Seating and Safety Restraints Adjusting second row bucket and bench seat back Lift the handle to adjust seatback. Using same control will fold the seatback flat. Note: For the bench seat only, make sure the center safety belt is unbuckled before folding the seatback.
Page 172 Seating and Safety Restraints 2. Fold the head outboard restraint by pulling the head restraint release strap. Note: Outboard head restraints do not adjust vertically. 3. Lift the handle located on the side of the seat. The seatback will fold flat. 4.
Page 173 Seating and Safety Restraints 5. To return the seatback to the floor from tumbled position, rotate the seat down until you hear it latching to the floor. 6. To return the seatback to the upright position • Lift the seatback toward the rear of the vehicle, and •...
Page 174 Seating and Safety Restraints Press the control located at the back of the rear door opening one time to fold the seat back down and tumble the seat forward for access to the 3rd row. Exiting the third row seat 1.
Page 175 Seating and Safety Restraints 4. To return the seatback to the upright position • Lift the seatback toward the rear of the vehicle, and • Rotate the seatback until you hear a click, locking it in the upright position. Note: The seatback will not raise if the rear latch hooks are not properly engaged to the floor striker.
Page 176 Seating and Safety Restraints WARNING: Do not adjust or release the seat floor latch while vehicle is in motion. Do not operate the vehicle with seats in tumbled position. Always latch the vehicle seat to the floor, whether the seat is occupied or empty. If not latched or if the seat is tumbled, the seat may cause injury during a sudden stop.
Page 177 Seating and Safety Restraints Note: Do not use the seat anchors as cargo tie downs. Note: Do not use the third row seatback as a load floor when the seatback is folded. Note: Ensure that the area under the seat is free of objects before stowing it.
Page 178 Seating and Safety Restraints 2. To return the seatback to upright position, pull the number 1 strap, then while holding the number 1 strap, pull the long strap located on the seatback to raise the seatback. 3. Pull the head restraints up to their normal positions.
Page 179 Seating and Safety Restraints obstacle detection that allows the seat to stop and reverse direction if it hits an obstacle so that the obstacle can be removed. The third row power seat buttons are located behind the third row seats on the left-hand quarter trim panel.
Page 180: Personal Safety System
Seating and Safety Restraints Note: In the unlikely event that the third row power seat stops prematurely, or travels to an unexpected position, press the FOLD button (3) to reset the seat and return it to a normal position. Folding the head restraints manually The head restraints can also be folded manually without folding/stowing the seat.
Page 181 Seating and Safety Restraints • Restraint system warning light and backup tone. • The electrical wiring for the airbags, crash sensor(s), safety belt pretensioners, front safety belt usage sensors, driver seat position sensor, front passenger sensing system, and indicator lights. How does the Personal Safety System™...
Page 182 Seating and Safety Restraints Front passenger sensing system For airbags to do their job they must inflate with great force, and this force can pose a potentially deadly risk to occupants that are very close to the airbag when it begins to inflate. For some occupants, this occurs because they are initially sitting very close to the airbag.
Page 183: Safety Belt System
Seating and Safety Restraints safety belt pretensioners can be activated alone or, if the collision is of sufficient severity, together with the front airbags. Front safety belt energy management retractors The front outboard safety belt energy management retractors allow webbing to be pulled out of the retractor in a gradual and controlled manner in response to the occupant’s forward momentum.
Page 184 Seating and Safety Restraints WARNING: To reduce the risk of injury, make sure children sit where they can be properly restrained. WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision.
Page 185 Seating and Safety Restraints WARNING: Front and rear seat occupants, including pregnant women, should wear safety belts for optimum protection in an accident. Combination lap and shoulder belts (standard belts shown, 2nd row inflatable belts similar-if equipped) 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel...
Page 186 Seating and Safety Restraints Pregnant women should always wear their safety belt. The lap belt portion of a combination lap and shoulder belt should be positioned low across the hips below the belly and worn as tight as comfort will allow.
Page 187 Seating and Safety Restraints How to use the automatic locking mode Non-inflatable safety belts • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion of the belt and pull downward until the entire belt is pulled out. Rear outboard inflatable safety belts (second row only—if equipped) •...
Page 188 Seating and Safety Restraints Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. Rear Inflatable Safety Belt (if equipped) The rear inflatable safety belts are fitted in the shoulder safety belts of the second-row outboard seating positions.
Page 189 Seating and Safety Restraints How does the rear inflatable safety belt system work? • The rear inflatable safety belts will function like standard restraints in everyday usage. • During a collision of sufficient force, the inflatable belt will deploy. The shoulder portion of the inflatable belt will inflate from inside the webbing.
Page 190 Seating and Safety Restraints WARNING: If the rear inflatable safety belt has deployed, it will not function again. The rear inflatable safety belt system must be inspected and serviced by an authorized dealer. Energy management feature — front outboard • This vehicle has a safety belt system with an energy management feature at the front seats to help further reduce the risk of injury in the event of a head-on collision.
Page 191 Seating and Safety Restraints WARNING: Do not use extensions with an inflatable safety belt. WARNING: Do not use extensions to change the fit of the shoulder belt across the torso. Safety belt height adjustment Your vehicle has safety belt height adjustments for the front outboard seating positions.
Page 192 Seating and Safety Restraints Conditions of operation If... Then... The driver’s safety belt is not The safety belt warning light buckled before the ignition illuminates 1-2 minutes and the switch is turned to the on warning chime sounds 4-8 seconds. position...
Page 193 Seating and Safety Restraints If... Then... The driver’s and front The Belt-Minder feature will not passenger’s safety belts are activate. buckled before the ignition switch is turned to the on position or less than 1-2 minutes have elapsed since the ignition switch has been turned to on...
Page 194 Seating and Safety Restraints The following are reasons most often given for not wearing safety belts (All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we are exposed to “rare”...
Page 195 Seating and Safety Restraints Reasons given... Consider... “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help prevent ejection, WE CAN’T “PICK OUR CRASH”. WARNING: Do not sit on top of a buckled safety belt or insert a latchplate into the buckle to avoid the Belt-Minder chime.
Page 196 Seating and Safety Restraints WARNING: While the design allows you to deactivate your Belt-Minder , this system is designed to improve your chances of being safely belted and surviving an accident. We recommend you leave the Belt-Minder system activated for yourself and others who may use the vehicle.
Page 197: Airbags
Seating and Safety Restraints AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) The airbag supplemental restraint system (SRS) is designed to work in conjunction with the safety belts to help protect the driver and front outboard passenger from certain upper body injuries. The term “supplemental restraint”...
Page 198 Seating and Safety Restraints WARNING: Do not place any object between an occupant and an airbag or near any other airbag covering. The airbag may not inflate properly and might force an object into that person causing severe injury or death. The instrument panel grab handle should never be used for storage.
Page 199 Seating and Safety Restraints WARNING: Modifying or adding equipment to the front end of the vehicle (including frame, bumper, front end body structure and tow hooks) may affect the performance of the airbag system, increasing the risk of injury. Do not modify the front end of the vehicle.
Page 200 Seating and Safety Restraints The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the...
Page 201 Seating and Safety Restraints • a readiness light and tone. • diagnostic module. • the electrical wiring which connects the components. • Front passenger sensing system. Refer to Front passenger sensing system later in this chapter. • “Passenger airbag off” or “pass airbag off” indicator lamp. Refer to Front passenger sensing system later in this chapter.
Page 202 Seating and Safety Restraints Passenger airbag status indicator The front passenger sensing system uses a passenger airbag status indicator which will illuminate indicating that the front passenger frontal airbag is either ON (enabled) or OFF (disabled). The indicator lamp is located in the center stack of the instrument panel.
Page 203 Seating and Safety Restraints • If the passenger airbag status indicator OFF lamp remains lit even after this, the person should be advised to ride in the rear seat. Passenger Airbag Occupant Passenger Airbag Status Indicator OFF: Lit Empty Disabled ON: Unlit OFF: Lit Child...
Page 204 Seating and Safety Restraints • Objects stowed in the seatback map pocket (if equipped) • Objects placed on the occupant’s lap • Cargo interference with the seat • Other passengers pushing or pulling on the seat • Rear passenger feet and knees resting or pushing on the seat The conditions listed above may cause the weight of a properly seated occupant to be incorrectly interpreted by the front passenger sensing system.
Page 205 If it is necessary to modify an advanced front airbag system to accommodate a person with disabilities, contact the Ford Customer Relationship Center at the phone number shown in the Customer Assistance section of this Owner’s Guide or see your authorized dealer.
Page 206 Seating and Safety Restraints WARNING: Do not use accessory seat covers. The use of accessory seat covers may prevent the deployment of the side airbags and increase the risk of injury in an accident. WARNING: Do not lean your head on the door. The side airbag could injure you as it deploys from the side of the seatback.
Page 207 Seating and Safety Restraints The side airbags are fitted on the outboard side of the seatbacks of the front seats. In certain lateral collisions, the airbag on the side affected by the collision will be inflated. The airbag was designed to inflate between the door panel and occupant to further enhance the protection provided occupants in side impact collisions.
Page 208 Seating and Safety Restraints Safety Canopy System WARNING: Do not place objects or mount equipment on or near the headliner at the siderail that may come into contact with a deploying Safety Canopy . Failure to follow these instructions may increase the risk of personal injury in the event of a collision.
Page 209 Seating and Safety Restraints How does the Safety Canopy System work? The design and development of the Safety Canopy system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group.
Page 210 Seating and Safety Restraints The Safety Canopy is mounted to roof side-rail sheet metal, behind the headliner, above each row of seats. In certain lateral collisions or rollover events, the Safety Canopy system will be activated, regardless of which seats are occupied. The Safety Canopy is designed to inflate between the side window area and occupants to further enhance protection provided in side impact collisions and rollover events.
Page 211: Child Restraints
Seating and Safety Restraints • A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and light are repaired. If any of these things happen, even intermittently, have the SRS serviced at your an authorized dealer immediately. Unless serviced, the system may not function properly in the event of a collision or rollover event.
Page 212 Recommendations for Safety Restraints are based on probable child height, age and weight thresholds from NHTSA and other safety organizations or are the minimum requirements of law. Ford recommends checking with a NHTSA Certified Child Passenger Safety Technician (CPST) and consult your pediatrician to make sure your child seat is appropriate for your child, and is compatible with and properly installed in the vehicle.
Page 213 Seating and Safety Restraints Recommendations for Safety Restraints for Children Recommended Child size, height, weight, or age restraint type Larger Children who have outgrown or no Use a vehicle children longer properly fit in a belt-positioning safety belt having booster seat (generally children who are the lap belt snug at least 4 feet 9 inches (1.45 meters) and low across the...
Page 214 Seating and Safety Restraints Recommendations for attaching child safety restraints for children Use any attachment method as indicated below by “X” LATCH LATCH Safety Safety Safety (lower (lower belt belt and belt Restraint Child anchors anchors LATCH only Type Weight only) (lower tether...
Page 215 Seating and Safety Restraints WARNING: Always carefully follow the instructions and warnings provided by the manufacturer of any child restraint to determine if the restraint device is appropriate for your child’s size, height, weight, or age. Follow the child restraint manufacturer’s instructions and warnings provided for installation and use in conjunction with the instructions and warnings provided by the vehicle manufacturer.
Page 216 Seating and Safety Restraints training to ensure that all children ages 0 to 16 are properly restrained in the correct restraint system. Ford recommends checking with a NHTSA Certified Child Passenger Safety Technician (CPST) and your pediatrician to make sure your seat is appropriate for your child and properly installed in the vehicle.
Page 217 Seating and Safety Restraints Airbags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the vehicle seat all the way back.
Page 218 Seating and Safety Restraints Perform the following steps when installing the child seat with combination lap/shoulder belts: Note: Although the child seat illustrated is a forward facing child seat, the steps are the same for installing a rear facing child seat. 1.
Page 219 Seating and Safety Restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until you hear a snap and feel the latch engage.
Page 220 Seating and Safety Restraints 5. To put the retractor in the automatic locking mode, do the following: • Standard safety belt: grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out. • Inflatable safety belt: grasp the lap portion of the inflatable safety belt and pull upward until all of the belt is pulled out.
Page 221 1 inch (2.5 cm) of movement for proper installation. Ford recommends checking with a NHTSA Certified Child Passenger Safety Technician (CPST) to make certain the child restraint is properly installed. In Canada, check with your local St. John Ambulance office for referral to a CPST.
Page 222 Seating and Safety Restraints Attaching child safety seats with LATCH (Lower Anchors and Tethers for CHildren) attachments The LATCH system is composed of three vehicle anchor points: two (2) lower anchors located where the vehicle seat back and seat cushion meet (called the “seat bight”) and one (1) top tether anchor located behind that seating position.
Page 223 Seating and Safety Restraints The LATCH anchors for child seat installation are located at the rear section of the rear seat between the cushion and seat back, below the locator symbols on the seatback. Follow the child seat manufacturer’s instructions to properly install a child seat with LATCH attachments.
Page 224 Seating and Safety Restraints WARNING: The standardized spacing for LATCH lower anchors is 280 mm (11 inches) center to center. Do not use LATCH lower anchors for the center seating position unless the child seat manufacturer’s instructions permit and specify using anchors spaced at least as far apart as those in this vehicle.
Page 225 Seating and Safety Restraints The tether strap anchors in your vehicle are in the following positions (shown from top view): • Second row bucket seats and rear seat • Second row bench seats and rear seat Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor.
Page 226 Seating and Safety Restraints Perform the following steps to attach a child safety seat to the tether anchor: 1. Route the tether strap: • Second row outboard seat positions: route the child safety seat tether strap over the seatback, under the head restraint and between the head restraint posts.
Page 227 If the safety seat is not anchored properly, the risk of a child being injured in a collision greatly increases. If your child restraint system is equipped with a tether strap, and the child restraint manufacturer recommends its use, Ford also recommends its use. 2011 Explorer (exp)
Page 228 To improve the fit of both the lap and shoulder belt on children who have outgrown child safety seats, Ford Motor Company recommends use of a belt-positioning booster. Booster seats position a child so that vehicle lap/shoulder safety belts fit better.
Page 229 Seating and Safety Restraints Booster seats should be used until you can answer YES to ALL of these questions when seated without a booster seat: • Can the child sit all the way back against the vehicle seat back with knees bent comfortably at the edge of the seat cushion? •...
Page 230 Seating and Safety Restraints • High back booster seats If, with a backless booster seat, you cannot find a seating position that adequately supports your child’s head, a high back booster seat would be a better choice. Children and booster seats vary in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder.
Page 231 Refer to the child restraint manufacturer’s instructions for additional inspection and maintenance information specific to the child restraint. Ford Motor Company recommends that all safety belt assemblies in use in vehicles involved in a collision be replaced.
Page 232 Seating and Safety Restraints WARNING: Failure to inspect and if necessary replace the safety belt assembly or child restraint system under the above conditions could result in severe personal injuries in the event of a collision. 2011 Explorer (exp) Owners Guide, 3rd Printing USA (fus)
Page 233: Tires, Wheels And Loading
Tires, Wheels and Loading NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed...
Page 234 Tires, Wheels and Loading Power is supplied to all four wheels through a transfer case or power transfer unit. 4WD vehicles allow you to select different drive modes as necessary. Information on transfer case operation and shifting procedures can be found in the Driving chapter. Information on transfer case maintenance can be found in the Maintenance and Specifications chapter.
Page 235 Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford Motor Company to give you the following information about tire grades exactly as the government has written it.
Page 236 Tires, Wheels and Loading government test course. For example, a tire graded 150 would wear one and one-half (1 ⁄ ) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate.
Page 237 Tires, Wheels and Loading • Tire Identification Number (TIN): A number on the sidewall of each tire providing information about the tire brand and manufacturing plant, tire size and date of manufacture. Also referred to as DOT code. • Inflation pressure: A measure of the amount of air in a tire. •...
Page 238: Tire Inflation
Ford Motor Company. You are strongly urged to buy a reliable tire pressure gauge, as automatic service station gauges may be inaccurate. Ford recommends the use of a digital or dial-type tire pressure gauge rather than a stick-type tire pressure gauge.
Page 239 Tires, Wheels and Loading To check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from driving even a mile. If you are checking tire pressure when the tire is hot, (i.e. driven more than 1 mile [1.6 km]), never “bleed”...
Page 240 Tires, Wheels and Loading the valve stem. Inspect the tire sidewalls for cracking, cuts, bruises and other signs of damage or excessive wear. If internal damage to the tire is suspected, have the tire demounted and inspected in case it needs to be repaired or replaced.
Page 241 (such as P-metric versus LT-metric or all-season versus all-terrain) as those originally provided by Ford. The recommended tire and wheel size may be found on either the Safety Compliance Certification Label or the Tire Label which is located on the B-Pillar or edge of the driver’s door.
Page 242 The tire pressure sensors mounted in the wheels (originally installed on your vehicle) are not designed to be used in aftermarket wheels. The use of wheels or tires not recommended by Ford Motor Company may affect the operation of your tire pressure monitoring system.
Page 243 Tires, Wheels and Loading • Do not run over curbs or hit the tire against a curb when parking WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion.
Page 244 Tires, Wheels and Loading • Front-wheel drive (FWD)/All-wheel drive (AWD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation.
Page 245 Tires, Wheels and Loading Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below. (Note that the tire size, load index and speed rating for your vehicle may be different from this example.) 1.
Page 246 Tires, Wheels and Loading Note: You may not find this information on all tires because it is not required by federal law. Letter rating Speed rating - mph (km/h) 81 mph (130 km/h) 87 mph (140 km/h) 99 mph (159 km/h) 106 mph (171 km/h) 112 mph (180 km/h) 118 mph (190 km/h)
Page 247 Tires, Wheels and Loading 12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 ⁄...
Page 248 Tires, Wheels and Loading Additional information contained on the tire sidewall for “LT” type tires “LT” type tires have some additional information beyond those of “P” type tires; these differences are described below. Note: Tire Quality Grades do not apply to this type of tire. 1.
Page 249 Tires, Wheels and Loading Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example.
Page 250: Tire Pressure Monitoring System (Tpms)
Tires, Wheels and Loading TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.)
Page 251 Tires, Wheels and Loading The tire pressure monitoring system complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Page 252 Tires, Wheels and Loading When your temporary spare tire is installed When one of your road tires needs to be replaced with the temporary spare, the TPMS will continue to identify an issue to remind you that the damaged road wheel/tire needs to be repaired and put back on your vehicle.
Page 253 Tires, Wheels and Loading Low tire pressure Possible cause Customer action required warning light Solid warning light Tire(s) 1. Check your tire pressure to under-inflated ensure tires are properly inflated; refer to Inflating your tires in this chapter. 2. After inflating your tires to the manufacturer’s recommended inflation pressure as shown on the Tire...
Page 254 Tires, Wheels and Loading Low tire pressure Possible cause Customer action required warning light Flashing warning Spare tire in use Your temporary spare tire is in light use. Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality.
Page 255 SNOW TIRES AND CABLES WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety and performance of your vehicle, which could result in an increased risk of loss of vehicle control, vehicle rollover, personal injury and death.
Page 256: Vehicle Loading
Tires, Wheels and Loading VEHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/or trailer, to keep your loaded vehicle weight within its design rating capability, with or without a trailer. Properly loading your vehicle will provide maximum return of vehicle design performance.
Page 257 Tires, Wheels and Loading Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the Tire Label on the B-Pillar or the edge of the driver’s door (vehicles exported outside the US and Canada may not have a Tire Label).
Page 258 Tires, Wheels and Loading Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) –...
Page 259 Tires, Wheels and Loading GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’s door. The total load on each axle must never exceed its GAWR.
Page 260 Tires, Wheels and Loading • Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage, serious damage to the vehicle, loss of control and personal injury.
Page 261 Tires, Wheels and Loading GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers –...
Page 262 Tires, Wheels and Loading WARNING: Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury. Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lb.”...
Page 263: Trailer Towing
Tires, Wheels and Loading to transport the cement to your home? If you and your friend each weigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12 x 100) = 1400 - 440 - 1200 = - 240 lb. No, you do not have enough cargo capacity to carry that much weight.
Page 264 Tires, Wheels and Loading Follow these guidelines to ensure safe towing: • Do not tow a trailer until your vehicle has been driven at least 1,000 miles (1,600 km). • Consult your local motor vehicle laws for towing a trailer. •...
Page 265 Tires, Wheels and Loading Engine/Passengers/Trailer Class Maximum Maximum GCWR - lb Trailer Weight (kg) - lb (kg) 4WD vehicles 3.5L/6–passenger/Class I 7050 (3199) 2000 (907) 3.5L/7–passenger/Class I 7060 (3202) 2000 (907) 3.5L/6–passenger/Class III 10125 (4594) 5000 (2268) 3.5L/7–passenger/Class III 10125 (4594) 5000 (2268) *For towing trailers up to 3500 lb (1588 kg), use a weight-carrying hitch and ball which uniformly spreads the trailer tongue loads through...
Page 266 Tires, Wheels and Loading WARNING: Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system. Your vehicle may not have enough braking power and your chances of having a collision greatly increase. The braking system of the tow vehicle is rated for operation at the GVWR not GCWR.
Page 267: Recreational Towing
Tires, Wheels and Loading • After you have traveled 50 miles (80 km), thoroughly check your hitch, electrical connections and trailer wheel lug nuts. • If you are driving down a long or steep hill, shift to a lower gear. Do not apply the brakes continuously, as they may overheat and become less effective.
Page 268 Tires, Wheels and Loading • Do not exceed 65 mph (105 km/h) • Start the engine and allow it to run for five minutes at the beginning of each day and every six hours thereafter. With the engine running and your foot on the brake, shift into D (Drive) and then into R (Reverse) before shifting back into N (Neutral).
Page 269: Driving
Driving STARTING Positions of the ignition (if equipped) If your vehicle is equipped with a push button start system, refer to Push button start system in this section for ignition modes. 1. Off— locks the gearshift lever and allows key removal. This position also shuts the engine and all electrical accessories off.
Page 270 Driving WARNING: Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions. WARNING: If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately.
Page 271 Driving • Make sure the gearshift is in P (Park). 3. Turn the key to 3 (on) without turning the key to 4 (start). If your vehicle is equipped with a push button start system, refer to Push button start system in this section for ignition modes. Some warning lights will briefly illuminate.
Page 272 Driving Note: Cranking may be stopped at any time by turning the key to the off position. 3. After idling for a few seconds, release the parking brake, apply the brake, shift into gear and drive. Note: If the engine does not start on the first try, turn the vehicle to the off position, wait 10 seconds and try Step 2 again.
Page 273 Driving warning lights in the instrument cluster will illuminate, but the engine will remain off. Note: You can start the engine from any ignition mode. 4. Start — press the START/STOP button (for any length of time) while applying the brake pedal. Note: The indicator light on the start button will illuminate when the vehicle is in on mode and when the engine is started.
Page 274 Driving off. If you switch your vehicle off with the shifter in any position other than P (Park), the message SHIFT TO PARK will be displayed in the message center. If the vehicle is left in this state, your key in ignition chime will activate when the driver door is opened, and you may drain your vehicle’s battery.
Page 275 Driving WARNING: Failure to follow engine block heater instructions could result in property damage or physical injury. WARNING: To reduce the risk of electrical shock, do not use your heater with ungrounded electrical systems or two-pronged (cheater) adapters. Prior to using the engine block heater, follow these recommendations for proper and safe operation: •...
Page 276: Brakes
Driving • Finally, have the engine block heater system checked during your fall tune-up to be sure it’s in good working order. How to use the engine block heater Ensure the receptacle terminals are clean and dry prior to use. To clean them, use a dry cloth.
Page 277 Driving effectiveness of the ABS and will increase your vehicle’s stopping distance. The ABS will be activated immediately, allowing you to retain steering control during hard braking and on slippery surfaces. However, the ABS does not decrease stopping distance. Brake assist The brake assist system provides full braking force during panic braking situations.
Page 278: Advancetrac
Driving The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the BRAKE ignition is turned on) until the parking brake is released. WARNING: Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park). Turn the ignition to the lock position and remove the key whenever you leave the vehicle.
Page 279 Driving WARNING: Vehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire construction and/or wheel/tire size may change the handling characteristics of the vehicle and may adversely affect the performance of the AdvanceTrac with RSC system. In addition, installing any stereo loudspeakers may interfere with and adversely affect the AdvanceTrac with RSC system.
Page 280 Driving The AdvanceTrac with RSC system includes a traction control off selection in the message center. The stability control light and stability control off light in the instrument cluster will illuminate temporarily during start-up as part of a normal system self-check, or during driving if a driving situation causes the AdvanceTrac with RSC system to operate.
Page 281 Driving brakes to cool down. In this situation, TCS will use only engine power reduction or transfer to help control the wheels from over-spinning. When the brakes have cooled down, the system will regain all features. Anti-lock braking, RSC , ESC and Curve Control are not affected by this condition and will continue to function during the cool-down period.
Page 282 Driving Certain adverse driving maneuvers may activate the RSC system, which include: • Emergency lane-change • Taking a turn too fast • Quick maneuvering to avoid an accident, pedestrian or obstacle Curve Control Curve control may enhance your vehicle’s ability to follow the road during adverse maneuvers, for example when cornering severely or avoiding objects in the roadway.
Page 283 Driving Note: Curve Control can be disabled with the terrain management control (if equipped). See Terrain Management later in this chapter. AdvanceTrac Features Stability control Message Operation Mode light center display Turns on Default at System None Enabled start-up initialization start-up Traction TRACTION...
Page 284: Hill Descent Control
WARNING: Turning off trailer sway control increases the risk of loss of vehicle control, serious injury, or death. Ford does not recommend disabling this feature except in situations where speed reduction may be detrimental (e.g., hill climbing), the driver has...
Page 285 Driving Enabling hill descent control and setting the descent speed 1. Press and release the hill descent button located in the center of the terrain management control. A light in the control will illuminate and chime will sound when this feature is activated.
Page 286 Driving If your vehicle loses electrical power while you are driving (or if the ignition is turned off), you can steer the vehicle manually, but it takes more effort. Extreme continuous steering may increase the effort it takes for you to steer. This occurs to prevent overheating and permanent damage to your steering system.
Page 287 Driving A high crown in the road or high crosswinds may also make the steering seem to wander/pull. PREPARING TO DRIVE WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles. WARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.
Page 288 Driving If the fuse is not blown and the brake lamps are working properly, the following procedure will allow you to move the gearshift lever from P (Park): 1. Apply the parking brake and turn the ignition off. 2. Open the small forward storage compartment, and remove the rubber protective cover.
Page 289: Transmission Operation
Driving AUTOMATIC TRANSMISSION OPERATION Automatic transmission adaptive learning Your transmission is equipped with an adaptive learning strategy found in the vehicle computer. This feature is designed to increase durability and provide consistent shift feel over the life of the vehicle. A new vehicle or transmission may have firm and/or soft shifts.
Page 290 Driving N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. D (Drive) with Overdrive The normal driving position for the best fuel economy. Transmission operates in gears one through six.
Page 291 Driving D (Drive) with Grade Assist Pressing the transmission control switch on the side of the gearshift lever activates grade assist and cancels overdrive. Grade assist: • Provides additional grade (engine) braking and extends lower gear operation on uphill climbs for hilly terrain or mountainous areas.
Page 292 Driving the ability for the driver to change gears up or down. By moving the gearshift lever from D (Drive) to M (Manual), you now have control of selecting the gear you desire using the toggle switch on the gearshift lever.
Page 293 Driving start assist feature is active, the vehicle will remain stationary on the slope for up to two seconds after you release the brake pedal. During this time, you have time to move your foot from the brake to the accelerator pedal and pull away.
Page 294: Reverse Sensing System
Driving Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur. Do not rock the vehicle for more than a minute or damage to the transmission and tires may occur, or the engine may overheat. REVERSE SENSING SYSTEM (IF EQUIPPED) The reverse sensing system (RSS) sounds a tone to warn the driver of obstacles near the rear bumper when the R (Reverse) gear is selected...
Page 295 Driving The RSS detects obstacles up to six feet (two meters) from the rear bumper with a decreased coverage area at the outer corners of the bumper, (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases.
Page 296: Rear-View Camera System
Driving REARVIEW CAMERA SYSTEM (IF EQUIPPED) The rear video camera system, located on the liftgate above the license plate, provides a video image of the area behind the vehicle. It adds assistance to the driver while reversing or reverse parking the vehicle.
Page 297 Driving To use active guidelines, turn the steering wheel and point the active guidelines towards an intended path. If the steering wheel position is changed while reversing, the vehicle might deviate from the original intended path. Active guidelines project the intended path of the vehicle. Fixed guidelines show the actual direction the vehicle is moving.
Page 298 Driving appear between the buttons (i.e. Level 1). When activating manual zoom mode, the system always starts from OFF. When enabled, Level 1, Level 2, or Level 3 will only be active while the vehicle is in R (Reverse). The feature disables outside of R (Reverse) and must be re-enabled the next time the vehicle shifts into R (Reverse).
Page 299 Driving After activating or deactivating a rear video camera feature, the touchscreen will show a preview of the feature(s) selected. Note: If the camera system image is not clear or seems distorted, it may be covered with water droplets, snow, mud or any other substance. If this occurs, clean the camera lens before using the camera system.
Page 300 Driving reverse lamps are operating in order to get a clear image in the dark. If either of the lamps are not operating, stop using the camera system, at least in the dark, until the lamp(s) are replaced and functioning. Servicing •...
Page 301 Driving Operation The radar sensor detects vehicles ahead that are moving in the same direction as your vehicle. If the radar detects that your vehicle is rapidly closing on another vehicle a red warning light will illuminate and an audible warning chime will sound.
Page 302 Driving WARNING: The collision warning system’s brake support can only help reduce the speed at which a collision occurs if the driver applies the vehicle’s brakes. The brake pedal must be pressed just like for any typical braking situation. Blocked sensor If a message regarding a blocked sensor is displayed, the radar signals from the sensor, located behind a...
Page 303 Driving Activating/deactivating collision warning system To turn the warning system and/or chime on or off and set the warning sensitivity <– –>, refer to Message center in the Instrument Cluster chapter. Note: If the system cannot be turned off in a MyKey™ equipped vehicle, refer to MyKey™...
Page 304 Driving Automatic search for parking space To start, press the APA control switch (on the left side of the instrument panel below the headlamp switch). The touch screen will display SEARCHING FOR PARKING SPACE ON RIGHT (LEFT/SIDE) and a corresponding graphic.
Page 305 Driving Automatic steering into parking space Automatic steering is activated when you stop the vehicle, remove your hands from the steering wheel and select the R (Reverse) gear. Be sure the steering wheel motion is not obstructed by any objects. The vehicle will steer itself from this point on as you follow the instructions in the touch screen to safely move the vehicle reverse and forward in the space.
Page 306 Driving The system may offer subsequent backward and forward maneuvers before proceeding to the finish phase. APA finished When active park assist has completed the automated steering, the touch screen displays ACTIVE PARK ASSIST FINISHED followed by a chime. The driver is responsible to assess and correct as necessary the final parking position and put the vehicle in P (Park).
Page 307 Driving • the front bumper or side sensors are damaged (i.e. in a collision) or obstructed by a foreign object (i.e. front bumper cover). • a mini-spare tire is used. Troubleshooting Why isn’t APA searching for a parking space? • You may have deactivated the AdvanceTrac system. •...
Page 308 Driving • The vehicle had a repair or alteration that is not authorized by the manufacturer. • One of the parked vehicles has a high altitude attachment (i.e. salt sprayer, snow plow, moving truck high bed, etc.) High altitude attachments may not be detected by the system. •...
Page 309 Driving WARNING: Objects in the blind spot mirror are closer than they appear. BLIND SPOT INFORMATION SYSTEM (BLIS ) WITH CROSS TRAFFIC ALERT (CTA) (IF EQUIPPED) The BLIS is a convenience feature that aids the driver in assessing whether a vehicle is within an area on either side of the vehicle extending rearward from the outside mirrors to approximately 10 feet...
Page 310 Driving including zero mph. BLIS is also active if the transmission is placed in N (Neutral). If the transmission is shifted out of D (Drive) or N (Neutral) the system will enter the CTA mode (see CTA operation below). Once shifted back in to D (Drive) the BLIS mode will activate once driven above 3 mph (5 km/h).
Page 311 Driving concrete walls, cyclone fencing, sharp turns around a pole or building, or coming to a stop with a vehicle directly behind but very close. False alerts are temporary and self correct. Cross traffic alert (CTA) system operation The CTA system warns the driver of approaching vehicles when R (Reverse) is selected and the vehicle is backing out of a front-in parking spot.
Page 312 Driving The CTA system detects vehicles approaching up to 45 feet (14 meters) away. Coverage decreases when vehicles and objects in close proximity block the CTA sensors (refer to figure for approximate zone coverage areas [sensor obstructed for vehicle on left]). Backing slowly from the parking spot in these situations helps to increase the sensor coverage and effectiveness.
Page 313 Driving CTA detection limitations: Due to the nature of radar technology, there may be certain instances where vehicles entering and exiting the blind spot zones may not be detected. Below is a list of circumstances that may cause non-detection: • Debris build-up on the rear quarter panel fascias •...
Page 314 Driving BLIS and/or CTA fault operation If the BLIS and/or CTA senses a fault on either the left or right sensor, the BLIS alert indicator will go on and remain on and the message center will display BLIND SPOT SYSTEM FAULT or CROSS TRAFFIC SYSTEM FAULT.
Page 315 Driving The following table lists possible causes and actions for this message being displayed: The surface of the radar is dirty or Clean the fascia area in front of obstructed in some way the radar, either side, or remove obstruction. The surface of the radar is not Drive normally in traffic for a few dirty or obstructed...
Page 316 Driving Your vehicle is equipped with an intelligent 4WD system that continuously monitors vehicle conditions and automatically adjusts the power distribution between the front and rear wheels. It combines transparent all-surface operation with highly capable four-wheel drive. The 4WD system is always active and requires no driver input. It is capable of handling all road conditions, including street and highway driving as well as off-road and winter driving.
Page 317 Driving pavement only after reducing your speed. Do not turn the steering wheel too sharply while returning to the road surface. • It may be safer to stay on the apron or shoulder of the road and slow down gradually before returning to the pavement. You may lose control if you do not slow down or if you turn the steering wheel too sharply or abruptly.
Page 318 Driving WARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander. Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turn must be made, remember to avoid “over-driving” your vehicle, i.e., turn the steering wheel only as rapidly and as far as required to avoid the emergency.
Page 319 Ford Motor Company joins the U.S. Forest Service and the Bureau of Land Management in encouraging you to help preserve our national forest and other public and private lands by “treading lightly.”...
Page 320 Driving slopes or hills. A danger lies in losing traction, slipping sideways and possibly rolling over. Whenever driving on a hill, determine beforehand the route you will use. Do not drive over the crest of a hill without seeing what conditions are on the other side. Do not drive in reverse over a hill without the aid of an observer.
Page 321 Ford Motor Company recommends that caution be used with any vehicle equipped with a high load or device (such as ladder racks or pickup box cover).
Page 322 Driving and adversely affect driver and passenger safety. Frequent inspection of vehicle chassis components is recommended if the vehicle is subjected to heavy off-road usage. TERRAIN MANAGEMENT (IF EQUIPPED) Terrain management adapts the responses of the vehicle’s engine, transmission, 4WD system, suspension, and stability control systems to match the demands of the terrain.
Page 323 Driving • Sand - This mode should be used for soft dry sand, or deep gravel terrain. If the sand to be crossed is damp/wet, and sufficiently deep enough to cause the wheels to sink into the surface, the Mud/Ruts mode should be selected.
Page 324: Roadside Emergencies
ROADSIDE ASSISTANCE Vehicles sold in the U.S. : Getting roadside assistance To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: •...
Page 325: Hazard Flasher Control
U.S. Ford and Lincoln vehicle customers who require Roadside Assistance, call 1-800-241-3673. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount for towing to the nearest dealership within 35 miles (56 km). To obtain reimbursement information, U.S.
Page 326: Fuel Pump Shut-Off
WARNING: Failure to inspect and if necessary repair fuel leaks after a collision may increase the risk of fire and serious injury. Ford Motor Company recommends that the fuel system be inspected by an authorized dealer after any collision. FUSES AND RELAYS...
Page 327 Roadside Emergencies Standard fuse amperage rating and color COLOR Fuse Standard Cartridge Mini fuses Maxi fuses rating fuses maxi fuses Grey Grey — — Violet Violet — — Pink Pink — — — — 7.5A Brown Brown — — — —...
Page 328 Roadside Emergencies The fuses are coded as follows: Fuse/Relay Fuse Amp Protected Circuits Location Rating One touch up/down driver side front window Not used (spare) One touch up/down passenger side front window Interior demand lamps (overhead console, 2nd row, cargo), glove box lamp, 2nd and 3rd row seat release, visor lamps Amplifier...
Page 329 Roadside Emergencies Fuse/Relay Fuse Amp Protected Circuits Location Rating 4” Radio display (without SYNC ), Power liftgate logic, Electronic finish panel Run/accessory relay (wipers, rear washer), Rain sensor Instrument cluster, Heads-up display Interior courtesy lamps (overhead console, 2nd row, cargo), Puddle lamps, Console bin LED, Backlighting Right turn lamps, Right trailer tow...
Page 330 Roadside Emergencies Fuse/Relay Fuse Amp Protected Circuits Location Rating Liftgate release Radio frequency module IA module Ignition switch, Push button start Radio, 8” SYNC Multi-function display screen, SYNC module, Global positioning system module Front park lamps Trailer tow brake controller 110V AC power point, Power folding mirror, Power mirrors, One touch up/down front...
Page 331 Roadside Emergencies Fuse/Relay Fuse Amp Protected Circuits Location Rating Not used (spare) Climate control module Fog lamps, left and right turn signal mirror feed 30A Circuit Rear power windows, Passenger Breaker power window, One touch down (driver side only) Delayed Body control module accessory relay Power distribution box...
Page 332 Roadside Emergencies 94 93 92 91 90 89 The high-current fuses are coded as follows: Fuse/Relay Fuse Amp Power Distribution Box Location Rating Description — Not used — Not used 30A** Trailer brake control module 30A** Wipers, Front washer 50A** Anti-lock brake system (ABS) pump —...
Page 333 Roadside Emergencies Fuse/Relay Fuse Amp Power Distribution Box Location Rating Description 40A** 110V AC power point 40A** Front blower motor 30A** Starter motor 20A** Power point #1/cigar lighter 20A** Power point #3 (cargo area) 30A** 3rd row seat module 30A** Driver power seat, Memory module 30A**...
Page 334 Roadside Emergencies Fuse/Relay Fuse Amp Power Distribution Box Location Rating Description — Not used — Not used — Not used 15A* Heated mirrors — Not used — Not used — TT left stop/turn lamps relay — Not used — Wiper relay —...
Page 335 Roadside Emergencies Fuse/Relay Fuse Amp Power Distribution Box Location Rating Description — Not used — Not used — Not used — TT park lamps relay 20A* Right HID headlamps Adaptive cruise control (ACC) — Not used — Not used 15A* Rear washer —...
Page 336 Ford. If the dissimilar spare tire or wheel is damaged, it should be replaced rather than repaired.
Page 337 Roadside Emergencies A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that is different in brand, size or appearance from the road tires and wheels and can be one of three types: 1. T-type mini-spare: This spare tire begins with the letter “T” for tire size and may have “Temporary Use Only”...
Page 338 Roadside Emergencies The usage of a full-size dissimilar spare tire/wheel can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability •...
Page 339 Roadside Emergencies 1. Remove the floor filler and carpeted floor panel located in the rear of the vehicle. 2. Remove the wing nut that secures the spare tire by turning it counterclockwise. 3. Lift and remove the spare tire from the spare tire well. 2011 Explorer (exp) Owners Guide, 3rd Printing USA (fus)
Page 340 Roadside Emergencies 4. Remove the wing bolt that secures the jack kit by turning it counterclockwise. 5. Remove the jack kit which includes jack (4), wheel wrench (lug wrench) (3), wheel chock (5), L-shaped bolt (1) and tow recovery hook (2). 6.
Page 341 Roadside Emergencies WARNING: To help prevent the vehicle from moving when you change a tire, be sure to place the transmission in P (Park), set the parking brake and block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed.
Page 342 Roadside Emergencies 3. Put the jack in the jack notch next to the tire you are changing. Turn the jack handle clockwise until the wheel is completely off the ground. 4. Remove the lug nuts with the lug wrench. 5. Replace the flat tire with the spare tire, making sure the valve stem is facing outward.
Page 343 Roadside Emergencies Push the button (1) to retract the wrench handle and place the wrench over the raised tab on the lower link and drop the tang (2) through the hole in the diagonally opposite upper link. Turn lead screw of jack clockwise until the arrow aligns with the circle indicator to secure the wrench onto the jack.
Page 344: Temporary Mobility Kit
Roadside Emergencies TEMPORARY MOBILITY KIT (IF EQUIPPED) Your vehicle may be equipped with a temporary mobility kit (located under the driver’s seat). To remove the temporary mobility kit, move the driver’s seat fully forward and pull the kit rearward, separating the Velcro strip on the kit from the Velcro patch on the carpet.
Page 345 • Do not drive the vehicle above 50 mph (80 km/h). • Do not drive further than 120 miles (200 km). Drive only to the closest Ford Motor Company authorized dealer or tire repair shop to have your tire inspected.
Page 346 Always store the kit in its original location. • After sealant use, the TPMS sensor and valve stem on the wheel must be replaced by an authorized Ford dealer. • When inflating a tire or other objects, use the black air hose only. Do not use the transparent hose which is designed for sealant application only.
Page 347 Roadside Emergencies • Operating the temporary mobility kit could cause an electrical disturbance in radio and DVD player operation. What to do when a tire is punctured A tire puncture within the tire’s tread area can be repaired in two stages with the temporary mobility kit: •...
Page 348 Roadside Emergencies 4. Plug the power cable into the 12V power point in the vehicle. 5. Remove the warning sticker found on the canister and place it on the top of the instrument panel or the center of the dash. 6.
Page 349 Roadside Emergencies tire pressure has to be checked with the compressor in the OFF position to get the correct tire pressure reading. WARNING: Do not stand directly over the temporary mobility kit while inflating the tire. If you notice any unusual bulges or deformations in the tire’s sidewall during inflation, stop and call roadside assistance.
Page 350 After using the temporary mobility kit to seal your tire, you will need to replace the sealant canister and clear tube (hose). Sealing compound and spare parts can be obtained and replaced at an authorized Ford Motor Company dealership or tire dealer. Empty sealant bottles may be disposed of at home;...
Page 351 Roadside Emergencies Removal of the sealant canister from the temporary mobility kit 1. Unwrap the clear tube from the compressor housing. 2. Press the button located on the temporary mobility kit compressor housing below the canister while pulling up on the sealant canister. Installation of the sealant canister to the temporary mobility kit 1.
Page 352: Wheel Lug Nut Torque
3. Wrap the clear tube around the compressor housing. Note: If you experience any difficulties with the removal or installation of the sealant canister, consult your Ford Motor Company authorized dealer for assistance. Be sure to check the sealant compound’s “use by” date regularly.
Page 353 20 * Torque specifications are for nut and bolt threads free of dirt and rust. Use only Ford recommended replacement fasteners. WARNING: When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum or brake disc that contacts the wheel.
Page 354: Jump Starting
Roadside Emergencies WARNING: Do not insert the nozzle of portable fuel containers or aftermarket funnels into the Easy Fuel™ system. This could damage the fuel system and its seal, and may cause fuel to run onto the ground instead of filling the tank, all of which could result in serious personal injury.
Page 355 Roadside Emergencies Connecting the jumper cables Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery. 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
Page 356 Roadside Emergencies Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. 1. Remove the jumper cable from the ground metal surface.
Page 357: Wrecker Towing
It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. On FWD vehicles, if your vehicle is to be towed from the front, ensure proper wheel lift equipment is used to raise the front wheels off the ground.
Page 358 If the vehicle is towed by other means or incorrectly, vehicle damage may occur. Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for proper hook-up and towing procedures for your vehicle.
Page 359: Customer Assistance
A reasonable time must be allowed to perform a repair after taking your vehicle to the authorized dealer. Repairs will be made using Ford or Motorcraft parts, or remanufactured or other parts that are authorized by Ford.
Page 360 • The name of the authorized dealer and city where located • The vehicle’s current odometer reading In some states, you must directly notify Ford in writing before pursuing remedies under your state’s warranty laws. Ford is also allowed a final repair attempt in some states.
Page 361 In the case of 1 or 2 above, the consumer must also notify the manufacturer of the need for the repair of the nonconformity at the following address: Ford Motor Company 16800 Executive Plaza Drive Mail Drop 3NE-B Dearborn, MI 48126...
Page 362 THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer. If a warranty concern has not been resolved using the three-step procedure outlined earlier in this chapter in the Getting the services you need section, you may be eligible to participate in the BBB AUTO LINE program.
Page 363 (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Page 364 Telephone: (313) 594-4857 For customers in Guam, the Commonwealth of the Northern Mariana Islands (CNMI), America Samoa, and the U.S. Virgin Islands, please feel free to call our Toll-Free Number: (800) 841-FORD (3673). FAX: (313) 390-0804 Email: expcac@ford.com If your vehicle must be serviced while you are traveling or living in Puerto Rico, contact the nearest authorized dealer.
Page 365: Reporting Safety Defects (U.s. Only)
If you buy your vehicle in North America and then relocate to any of the above locations, register your vehicle identification number (VIN) and new address with Ford Motor Company Export Operations & Global Growth Initiatives by emailing expcac@ford.com. If you are in another foreign country, contact the nearest authorized dealer.
Page 366: Reporting Safety Defects (Canada Only)
Customer Assistance recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or Ford Motor Company. To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1–888–327–4236 (TTY: 1–800–424–9153); go to http://www.safercar.gov;...
Page 367: Cleaning
Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid.
Page 368 Cleaning WAXING • Wash the vehicle first. • Use a quality wax that does not contain abrasives. • Do not allow paint sealant to come in contact with any non-body (low-gloss black) colored trim, such as grained door handles, roof racks, bumpers, side moldings, mirror housings or the windshield cowl area.
Page 369 Cleaning • Do not spray a hot engine with cold water to avoid cracking the engine block or other engine components. • Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressure rinse clean. In Canada, use Motorcraft Engine Shampoo (CXC-66-A).
Page 370 Cleaning hot wax treatments used by commercial car washes, water repellent coatings, tree sap, or other organic contamination; these contaminants may cause squeaking or chatter noise from the blades, and streaking and smearing of the windshield. To clean these items, follow these tips: •...
Page 371 Cleaning • Do not use household or glass cleaners as these may damage the finish of the instrument panel, interior trim and cluster lens. • Do not allow air fresheners and hand sanitizers to spill on interior surfaces. If a spill occurs, wipe off immediately. Damage may not be covered by your warranty.
Page 372 Cleaning WARNING: Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt webbing. WARNING: On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side-airbag system and affect performance of the side airbag in a collision.
Page 373 Cleaning For routine cleaning, wipe the surface with a soft, damp cloth. For more thorough cleaning, wipe the surface with a mild soap and water solution. • Clean spills as quickly as possible. • Test any cleaner or stain remover on an inconspicuous part of the leather as cleaners may darken the leather.
Page 374 Cleaning FORD AND LINCOLN CAR CARE PRODUCTS Your Ford or Lincoln authorized dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle.
Page 375: Maintenance And Specifications
Maintenance and Specifications SERVICE RECOMMENDATIONS • Use the scheduled maintenance information to track routine service. • Use only recommended fuels, lubricants, fluids and service parts conforming to specifications. • Your authorized dealer can provide parts and service. PRECAUTIONS WHEN SERVICING YOUR VEHICLE •...
Page 376 Maintenance and Specifications OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood.
Page 377: Engine Compartment
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.5L V6 engine 1. Engine coolant reservoir 2. Brake fluid reservoir 3. Battery 4. Power distribution box 5. Air filter assembly 6. Transmission fluid dipstick (out of view) 7. Engine oil dipstick 8.
Page 378 In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specifications. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. They may cause squeaking, chatter noise, streaking and smearing.
Page 379 Maintenance and Specifications CHANGING THE WIPER BLADES 1. Pull the wiper blade and arm away from the glass. 2. Squeeze the locking tabs to release the blade from the arm and pull the blade away from the arm to remove it. 3.
Page 380: Engine Oil
Maintenance and Specifications 3. To attach the new wiper to the wiper arm, align the slot (1) and cross pin (2) and firmly press the wiper arm into the wiper blade until a click is heard. If you find this procedure too difficult, please see your dealer. ENGINE OIL Checking the engine oil Refer to the scheduled maintenance information for the appropriate...
Page 381 Approval Committee (ILSAC), comprised of U.S. and Japanese automobile manufacturers. To protect your engine and engine’s warranty, use Motorcraft SAE 5W-20 or an equivalent SAE 5W-20 oil meeting Ford specification WSS-M2C930-A. SAE 5W-20 oil provides optimum fuel economy and durability performance meeting all requirements for your...
Page 382: Battery
Change your engine oil and filter according to the appropriate schedule listed in the scheduled maintenance information. Ford production and Motorcraft replacement oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced.
Page 383 Maintenance and Specifications WARNING: Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.
Page 384 Maintenance and Specifications • If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned. When the battery is disconnected or a new battery installed, the transmission must relearn its adaptive strategy.
Page 385: Engine Coolant
When a battery replacement is required, the battery should only be replaced with a Ford recommended replacement battery that matches the electrical requirements of the vehicle. After battery replacement, or in some cases after charging the battery with an external charger, the BMS requires eight hours of vehicle sleep time (key off with doors closed) to relearn the new battery state of charge.
Page 386 Maintenance and Specifications The engine coolant should be within the COLD FILL RANGE as listed on the engine coolant reservoir. Refer to scheduled maintenance information for service interval schedules. If the engine coolant has not been checked at the recommended interval, the engine coolant reservoir may become low or empty.
Page 387 Maintenance and Specifications • DO NOT MIX different colors or types of coolant in your vehicle. Make sure the correct coolant is used. Mixing of engine coolants may harm your engine’s cooling system. The use of an improper coolant may harm engine and cooling system components and may void the warranty.
Page 388 Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled engine coolant since a Ford-approved recycling process is not yet available. Used engine coolant should be disposed of in an appropriate manner.
Page 389 Maintenance and Specifications • A coolant concentration of 60% will provide improved freeze point protection. Increased engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant and may cause engine damage. • If available, refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate freeze protection at the temperatures in which you drive in the winter months.
Page 390 Maintenance and Specifications WARNING: To reduce the risk of collision and injury, be prepared that the vehicle speed may reduce and the vehicle may not be able to accelerate with full power until the fluid temperatures reduce. The air conditioning may also cycle on and off during severe operating conditions to protect overheating of the engine.
Page 391 Maintenance and Specifications How fail-safe cooling works If the engine begins to overheat: • The engine coolant temperature gauge will move to the red (hot) area. • The coolant temperature warning light will illuminate. • The service engine soon indicator will illuminate. If the engine reaches a preset over-temperature condition, the engine will automatically switch to alternating cylinder operation.
Page 392 Maintenance and Specifications WARNING: Never remove the coolant reservoir cap while the engine is running or hot. 5. Re-start the engine and take your vehicle to an authorized dealer. Driving the vehicle without repairing the engine problem increases the chance of engine damage. Take your vehicle to an authorized dealer as soon as possible.
Page 393 Maintenance and Specifications • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent.
Page 394 Maintenance and Specifications Refueling WARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; •...
Page 395 Maintenance and Specifications 4. After you are done pumping fuel, slowly remove the fuel filler nozzle—allow about five seconds after pumping fuel before removing the fuel filler nozzle. This allows residual fuel to drain back into the fuel tank and not spill onto the vehicle. Note: A fuel spillage concern may occur if overfilling the fuel tank.
Page 396 Ask your fuel supplier about gasolines that meet the World-Wide Fuel Charter. Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines to improve air quality, per the recommendations in the Choosing the right fuel section. Running out of fuel Avoid running out of fuel because this situation may have an adverse effect on powertrain components.
Page 397 Maintenance and Specifications If you have run out of fuel: • You may need to cycle the ignition from off to on several times after refueling to allow the fuel system to pump the fuel from the tank to the engine. On restarting, cranking time will take a few seconds longer than normal.
Page 398 Maintenance and Specifications 3. Fill the vehicle with fuel from the portable fuel container. 4. When done, clean the funnel or properly dispose of it. Extra funnels can be purchased from your authorized dealer if you choose to dispose of the funnel. Do not use aftermarket funnels; they will not work with the Easy Fuel system and can damage it.
Page 399 Maintenance and Specifications • Use a known quality gasoline, preferably a national brand. • Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading (in miles or kilometers).
Page 400 Maintenance and Specifications • Driving at reasonable speeds (traveling at 55 mph [88 km/h] uses 15% less fuel than traveling at 65 mph [105 km/h]). • Revving the engine before turning it off may reduce fuel economy. • Using the air conditioner or defroster may reduce fuel economy. •...
Page 401 If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.
Page 402 Maintenance and Specifications Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working.
Page 403 Maintenance and Specifications Readiness for Inspection/Maintenance (I/M) testing Some state/provincial and local governments may have Inspection/Maintenance (I/M) programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. Your vehicle may not pass the I/M test if the service engine soon indicator is on or not working properly (bulb is burned out), or if the OBD-II system has determined...
Page 404 Maintenance and Specifications BRAKE FLUID The fluid level will drop slowly as the brakes wear, and will rise when the brake components are replaced. Fluid levels between the MIN and MAX lines are within the normal operating range; there is no need to add fluid.
Page 405 Maintenance and Specifications 5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary, refer to Identifying components in the engine compartment in this chapter for the location of the dipstick. 6. Install the dipstick making sure it is fully seated in the filler tube by turning it to the locked position.
Page 406: Air Filter(S)
Maintenance and Specifications Use of a non-approved automatic transmission fluid may cause internal transmission component damage. If necessary, add fluid in 1/2 pint (250 ml) increments through the filler tube until the level is correct. If an overfill occurs, excess fluid should be removed by an authorized dealer.
Page 407 Maintenance and Specifications 6. Replace the air filter housing cover and secure the clamps. Be sure that the air cleaner cover tabs are engaged into the slots of the air cleaner housing. Note: Failure to use the correct air filter element may result in severe engine damage.
Page 408 Maintenance and Specifications • Cover interior trim to prevent fading. • Keep all rubber parts free from oil and solvents. Engine • The engine oil and filter should be changed prior to storage, as used engine oil contain contaminates that may cause engine damage. •...
Page 409: Part Numbers
Replace the spark plugs with ones that meet Ford material and design specifications for your vehicle, such as Motorcraft or equivalent replacement parts. The customer warranty may be void for any damage to the engine if such spark plugs are not used.
Page 410 Maintenance and Specifications 2011 Explorer (exp) Owners Guide, 3rd Printing USA (fus)
Page 411 Maintenance and Specifications 2011 Explorer (exp) Owners Guide, 3rd Printing USA (fus)
Page 412 Maintenance and Specifications 2011 Explorer (exp) Owners Guide, 3rd Printing USA (fus)
Page 413: Engine Data
Maintenance and Specifications ENGINE DATA Engine 3.5L V6 engine Cubic inches Required fuel Minimum 87 octane Firing order 1-4-2-5-3-6 Ignition system EDIS Spark plug gap 0.049–0.053 inch (1.25–1.35mm) Compression ratio 10.8 :1 Engine drivebelt routing IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway Traffic Safety Administration Regulations require that a Safety Compliance...
Page 414 Maintenance and Specifications Vehicle identification number (VIN) The vehicle identification number is located on the driver side instrument panel. XXXXXXXXXXXXXXXXX Please note that in the graphic, XXXX is representative of your vehicle identification number. The Vehicle Identification Number (VIN) contains the following information: 1.
Page 415 Maintenance and Specifications TRANSMISSION CODE DESIGNATIONS You can find a transmission code on the Safety Compliance Certification Label. The following table tells you which transmission each code represents. Description Code Six-speed automatic (6F50) Six-speed automatic (6F55) 2011 Explorer (exp) Owners Guide, 3rd Printing USA (fus)
Page 416: Accessories
FORD CUSTOM ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford Custom Accessories are available for your vehicle through your local Ford or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
Page 417 Ford Motor Company engineering requirements. Contact your Ford dealer for details regarding the manufacturer’s limited warranty and/or a copy of the FLA product limited warranty offered by the accessory manufacturer.
Page 418: Ford Extended Service Plan
BaseCare – Covers 84 components. PowertrainCare – Covers 29 critical components. Ford ESP is honored by all Ford and Lincoln Dealers in the U.S. and Canada It’s the only extended service plan authorized and backed by Ford Motor Company. That means you get: •...
Page 419 Ford ESP Can Quickly Pay for Itself One service bill – the cost of parts and labor – can easily exceed the price of your Ford ESP Service Contract. With Ford ESP, you minimize your risk for unexpected repair bills and rising repair costs.
Page 420 Ford Extended Service Plan 2011 Explorer (exp) Owners Guide, 3rd Printing USA (fus)
Page 421 Ford Motor Company dealers. For more information, visit your local Ford of Canada dealer or www.ford.ca to find the Ford Extended Service Plan that is right for you. Note: Repairs performed outside of Canada and the United States are not eligible for Ford ESP coverage.
Page 422: Scheduled Maintenance
Your dealer has factory-trained technicians who can perform the required maintenance using genuine Ford parts. They are committed to meeting your service needs and to assuring your continuing satisfaction. Protecting your investment Maintenance is an investment that will pay dividends in the form of improved reliability, durability and resale value.
Page 423 Please consult your Warranty Guide for complete warranty information. Chemicals or additives not approved by Ford are not required for factory recommended maintenance. In fact, Ford Motor Company recommends against the use of such additive products unless specifically recommended by Ford for a particular application.
Page 424 Genuine Ford and Motorcraft replacement parts Dealerships stock Ford and Motorcraft branded replacement parts. These parts meet or exceed Ford Motor Company’s specifications, and we stand behind them. Parts installed at your dealership carry a nationwide, 12 month/12,000 mile (20,000 km) parts and labor limited warranty.
Page 425 In order to keep your vehicle running right, it is important to have the systems on your vehicle checked regularly. This can help identify potential issues and prevent major problems. Ford Motor Company recommends the following multi-point inspection be performed at every scheduled maintenance interval to help ensure your vehicle keeps running great.
Page 426 Scheduled Maintenance Multi-point inspection – Recommended each visit Accessory drive belt(s) Half-shaft dust boots (if equipped) Battery performance Horn operation Clutch operation (if equipped) Radiator, cooler, heater and A/C hoses Engine air filter Suspension components for leaks and damage Exhaust system Steering and linkage Exterior lamps and hazard Tires for wear and proper pressure,...
Page 427 Scheduled Maintenance 2011 Explorer (exp) Owners Guide, 3rd Printing USA (fus)
Page 428: Normal Scheduled Maintenance And Log
Scheduled Maintenance NORMAL SCHEDULED MAINTENANCE AND LOG For your convenience, your vehicle is equipped with a message center which determines the proper oil change service interval. You should perform the engine oil change as indicated by the message center. The message center will display ENGINE OIL CHANGE SOON or OIL CHANGE REQUIRED to indicate when an oil change is needed.
Page 429 Scheduled Maintenance 2011 Explorer (exp) Owners Guide, 3rd Printing USA (fus)
Page 430 Scheduled Maintenance Perform the services noted in the following table at the specified time/mileage (km) period either within 3,000 miles (4,800 km) of the OIL CHANGE REQUIRED message appearing in the message center or when the time/mileage (km) reading indicates service is due. Example #1: The OIL CHANGE REQUIRED message comes on at 28,751 miles (46,270 km);...
Page 431 Scheduled Maintenance Maintenance schedule log EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS...
Page 432 Scheduled Maintenance EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE...
Page 433 Scheduled Maintenance EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE...
Page 434 Scheduled Maintenance SPECIAL OPERATING CONDITIONS If you operate your vehicle primarily in one of the more demanding conditions listed below, you will need to have some items maintained more frequently. If you only occasionally operate your vehicle under these conditions, it is not necessary to perform the additional maintenance.
Page 435 Scheduled Maintenance Extensive idling and/or low-speed driving for long distances as in heavy commercial use such as delivery, taxi, patrol car or livery As required – Change engine oil and filter as indicated by message center and perform services listed in the Normal Scheduled Maintenance chart (except Fiesta) Inspect frequently, service as –...
Page 436 Scheduled Maintenance Operating in dusty conditions such as unpaved or dusty roads Inspect frequently, service as – Replace cabin air filter (if equipped) required – Replace engine air filter Every 5,000 miles (8,000 km) – Inspect the wheels and related components for abnormal noise, wear, looseness or drag –...
Page 437 Scheduled Maintenance Special operating condition log EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#:...
Page 438 Scheduled Maintenance EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE ILEAGE EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS OURS ILEAGE...
Page 439: Maintenance Product Specifications And Capacities
Normal vehicle axle maintenance Rear axles and power take-off (PTO) units containing synthetic fluid and light duty trucks equipped with Ford-design axles are lubricated for life. These fluids are not to be checked or changed unless a leak is suspected, service is required or the axle assembly has been submerged in water.
Page 440 Scheduled Maintenance Engine air filter & cabin air filter replacement Engine air filter and cabin air filter life is dependent on exposure to dusty and dirty conditions. Vehicles operated in these conditions will require frequent inspection and replacement of the engine air filter and cabin air filter. 2011 Explorer (exp) Owners Guide, 3rd Printing USA (fus)
Page 441: Engine Coolant Change Log
Scheduled Maintenance ENGINE COOLANT CHANGE RECORD Initial change 6 years or 100,000 miles (160,000 km) (whichever comes first) After initial change Every 3 years or 50,000 miles (80,000 km) Engine coolant change log EALER ALIDATION EALER ALIDATION P&A C P&A C RO#: RO#: OURS...
Page 442: Manual Heating And Air Conditioning
Index Selectshift (SST) ....291 Auxiliary input jack (Line in) ..60 Accessory delay ......99 Auxiliary power point ....95 Active Park Assist .....303 Axle Adaptive Cruise Control ...104 lubricant specifications ..410 AdvanceTrac ......278 refill capacities ......410 Airbag supplemental restraint system ......197, 205, 208 and child safety seats ....199 Battery ........382 description ....197, 205, 208...
Page 443 Index Changing a tire ......336 Ford Extended Service Plan ........418, 421 Child safety seats ......216 Getting assistance outside the in front seat ......217 U.S. and Canada .....363 in rear seat ......217 Getting roadside assistance ...324 LATCH ........222 Getting the service you recommendations ....214...
Page 444 Index idle speed control ....382 quality ........396 lubrication specifications ..410 running out of fuel ..353, 396 refill capacities ......410 safety information relating service points ......377 to automotive fuels ....392 Engine block heater ....274 Fuses ........326–327 Engine oil ........380 checking and adding ....380 dipstick ........380 filter, specifications ..381, 409 Garage door opener ....115...
Page 445 Index Inspection/maintenance (I/M) Liftgate ......123–124, 144 testing ........403 Lights, warning and indicator ..14 Instrument panel anti-lock brakes (ABS) ..277 cleaning ........370 Loading instructions ....263 cluster ........14 Load limits .........256 lighting up panel and interior ........78 Locks autolock ........138 Intelligent Access Key ....130 childproof ........141 Intelligent Access with push doors ........137...
Page 446 Index Overdrive ........289 illuminated entry ....147–148 locking/unlocking doors ..143 opening the trunk ....144 Remote start ......148 Parental MyKey replacement/additional programming ......131 transmitters ......147 Park Assist ........303 replacing the batteries ...145 Parking brake ......277 Remote start ......148 Parts (see Motorcraft Remote start climate parts) .........409 operation ........74 Passenger Occupant...
Page 447 Index Scheduled Maintenance Guide tilting .........93 Normal Scheduled Maintenance and Log .....428 Seats ..........159 Temporary mobility kit .....344 child safety seats ....216 Third-row power fold seat ..178 cleaning ........372 climate control ......166 Tilt steering wheel ......93 easy access/easyout Tire Pressure Monitoring feature ........169 System (TPMS) front seats .......161, 165...
Page 448 Index Washer fluid ......378 Water, Driving through .....323 Universal garage door opener ........115 Windows power .........97 rear wiper/washer .....93 Vehicle Identification Number Windshield washer fluid and (VIN) ..........414 wipers ..........91 Vehicle loading ......256 checking and adding fluid ..378 Ventilating your vehicle ...274 liftgate reservoir .....378 replacing wiper blades ...379 Wrecker towing ......357...

Ford Explorer 2011 Owner's Manual

Introduction

Instrument Cluster

Entertainment Systems

Climate Controls

Lights

Driver Controls

Locks and Security

Seating and Safety Restraints

Quick Links

Table of Contents

Troubleshooting

Related Manuals for Ford Explorer 2011

Summary of Contents for Ford Explorer 2011

Table of Contents