Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Globalsat BR-355
Summary of Contents for Globalsat BR-355
- Page 1 SERIAL GPS User’s Guide (WIN) Serial GPS Receiver BR-355...
- Page 2 Globalsat Technology Corporation or USGlobalsat, Inc. Globalsat/USGlobalsat hereby grants the right to download one (1) copy of this manual onto a hard drive for personal use. This manual is copyrighted and may contain proprietary information that is subject to change without...
-
Page 3: Table Of Contents
USB GPS (WIN) Table of Contents PACKAGE CONTENTS....................3 SYSTEM REQUIREMENTS.....................3 WELCOME........................3 1. GETTING STARTED....................4 2. INSTALLING THE USB DRIVER TO YOUR LAPTOP ..........4 3. COM PORT VERIFICATION..................5 4. INITIALIZING YOUR GPS RECEIVER...............5 5. USING / TESTING YOUR GPS RECEIVER ..............6 6. -
Page 4: Package Contents
Your can also download WIN driver if you are using the USB interface cable set at: www.usglobalsat.com/ SYSTEM REQUIREMENTS The BR-355 GPS receiver requires a compatible laptop or PDA device, the proper interface cable set and a 3 party NMEA compliant navigation software (not included).. -
Page 5: Getting Started
USB GPS (WIN) 1. GETTING STARTED For PDA applications you will need to purchase a separate cable set to interface the BR-355 GPS universal receiver head to your specific device. A list of available cable sets can be found at www.usglobalsat.com For Laptop applications you will need to purchase a separate cable set to interface the BR-355 GPS universal receiver head either the USB cable set,or the RS232 / PS2 cable set. -
Page 6: Com Port Verification
USB GPS (WIN) 3. COM PORT VERIFICATION 1. Once your serial GPS receiver has been connected (and/or your USB Driver installed), you will need to confirm which COM Port your PC (or PDA) which it had assigned in order to properly configure any software that will be utilizing the GPS data. -
Page 7: Using / Testing Your Gps Receiver
USB GPS (WIN) 5. USING / TESTING YOUR GPS RECEIVER Once the GPS receiver’s driver and your personal mapping software have been installed and configured properly, you can begin to use your navigation system by plugging the GPS into your devices port and launching your mapping software. - Page 8 USB GPS (WIN) The above screen shows the available satellites (numbers) and their signal strength. NOTE: Configuration (or selection) of an assigned COM port for the GPS device from within your mapping or charting software must be completed whenever using a software for the first time. PAGE 7 OF 13 USB_GPS_WIN_ v2..2...
-
Page 9: Un-Install The Usb Driver
If you are outdoors, the device has been configured properly, the GPS receiver should be on and receiving the streaming GPS data. This can be verified by opening your mapping software program. In addition, the Globalsat GPS has a built-in LED status indicator that shows the following: LED OFF: GPS receiver is off (no power). -
Page 10: Contact Information
9. SAFETY AND LEGAL NOTICES Please read this section carefully before using the GPS receiver Globalsat Technology Corporation / USGlobalsat, Inc. will not accept any responsibility whatsoever for accidents resulting from failure to observe common sense precautions. Your personal judgment, traffic regulations, and common sense must always take precedence over... - Page 11 USB GPS (WIN) vehicle operation or collision. For your safety, take care to route all cables away from shifters, pedals, accessory controls and mechanisms. WARNING: Drive safely and use common sense. It is your responsibility as the vehicle operator to drive safely, observe all traffic rules and above all use your own personal judgment while driving.
-
Page 12: Limited Warranty
Except as provided herein, Globalsat/USGlobalsat makes no express warranties’, including but not limited to any warranties of merchantability or fitness for particular use, or non-infringement. You acknowledge that your use of the product or service is at your sole risk and you agree that the information provided are without warranty of any kind by Globalsat/USGlobalsat. -
Page 13: Bu-353 Specifications
USB GPS (WIN) 11. BR-355 SPECIFICATIONS Electrical Characteristics (Receiver) GPS Chipset SiRF Star III e/LP Frequency L1, 1575.42 MHZ C/A Code 1.023 MHz chip rate Channels 20 all-in-view tracking Sensitivity -159 dBm Accuracy 5m 2D RMS WAAS enabled Position Horizontal...
Need help?
Do you have a question about the BR-355 and is the answer not in the manual?
Questions and answers