Page 1
Web Server Module User's Manual (Installation) QJ71WS96 Thank you for purchasing the Mitsubishi programmable logic controller MELSEC-Q Series. Prior to use, please read both this manual and detailed manual thoroughly to fully understand the product. MODEL QJ71WS96-U-HW-JE MODEL 13JT97 CODE IB(NA)-0800231-C(0311)MEE 2002 MITSUBISHI ELECTRIC CORPORATION...
SAFETY PRECAUTIONS (Be sure to read these instructions before using the product.) Before using this product, read this manual and the relevant manuals introduced in this manual carefully and handle the product correctly with full attention to safety. Note that these precautions apply only to this product. Refer to the user's manual of the CPU module for the PLC system safety precautions.
Page 3
[DESIGN PRECAUTIONS] CAUTION Do not bundle the control lines or communication cables with the main circuit or power lines, or bring them close to each other. The distance of 100mm(3.9inch) or more should be ensured. Failure to do so cause malfunctions due to noise. Do not power off a station where this module is mounted and do not reset the PLC CPU while storing the settings into the standard ROM of the module using a Web browser.
[WIRING PRECAUTIONS] CAUTION Be sure to fix communication cables and power cables to the module by ducts or clamps. Failure to do so may cause damage of the module or the cables due to accidental pull or unintentional shifting of the cables, or malfunctions due to poor contact of the cable.
Page 5
This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual.
CONTENTS 1. Overview......................1 2. Performance Specifications ................2 3. Mounting and Installation ................3 3.1 Handling Precautions ................3 3.2 Installation Environment ................3 4. Part Names....................4 5.External Wiring ....................6 5.1 Connecting to the 10BASE-T/100BASE-TX ..........6 5.2 Connecting to the RS-232 ................
Page 7
(13JR58) Compliance with the EMC Directive and the Low Voltage Directive When incorporating Mitsubishi PLC into other machine or equipment and making it comply with the EMC directive and the low voltage directive, refer to Chapter 3, "EMC Directive and Low Voltage Directive" of the User's Manual (Hardware) for the CPU module.
1. Overview This manual explains how to install the QJ71WS96 Web server module (hereinafter referred to as Web server module) and how to wire them with other devices. (Production list) Model name Product name Quantity QJ71WS96 QJ71WS96 Web server module...
2. Performance Specifications The following describes the performance specifications of the Web server module. For the general specifications of the Web server module, refer to the user's manual of the CPU module used. Item Specifications 10BASE-T/10BASE-TX Interface (*1) 10BASE-T 10BASE-TX Data transmission speed 10Mbps 100Mbps...
3. Mounting and Installation 3.1 Handling precautions (1) Do not drop or apply severe shock to the module case since it is made of resin. (2) Always make sure to touch the grounded metal to discharge the electricity charged in the body, etc., before touching the module. Failure to do so may cause a failure or malfunctions of the module.
4. Part Names [When LED cover is closed] [When LED cover is opened]...
Page 12
Name Description 1) LED Display Refer (1) LED display contents. 10BASE-T/ Used for connecting Web server module to 100BASE-TX interface 10BASE-T/100BASE-TX. connection connector (Web server module recognizes 10BASE-T/ (RJ45) 10BASE-TX according to the external device.) RS-232 interface Used for connecting Web server module to connection connector RS-232.
5. External Wiring 5.1 Connecting to the 10BASE-T/100BASE-TX Use the twisted pair cable that meets IEEE802.3 10-BASE-T/100BASE-TX standards when connecting to the 10BASE-T/10BASE-TX interface. (1) For 100Mbps Use either of the following cables. (a) Unshielded twisted pair cable (UTP cable), Category 5 (b) Shielded twisted pair cable (STP cable), Category 5 (2) For 10Mbps Use either of the following cables.
5.2 Connecting to the RS-232 Use the RS-232 cable when connecting to the RS-232 interface. (1) RS-232 connector specifications Signal Signal direction Signal name abbreviation Web module Modem CD(DCD) Data Carrier Detect RD(RXD) Received Data SD(TXD) Transmitted Data ER(DTR) Data Terminal Ready SG(GND) Signal Ground DR(DSR)
6. Setting from GX Developer Set the mode, default operation, battery error detection, logging monitor setting and response monitoring time for Web server module on the "Intelligent function module switch setting" screen. Switch Number Description Switch 1 Mode setting Default operation/Battery error detection setting/ Switch 2 logging monitor setting Switch 3 (lower byte)
Page 16
0: Operates according to the account setting. 1: Displays the latest file update time. 1: Operates according to the default setting. Battery error detection setting User name : QJ71WS96 Password : MITSUBISHI 0: Detects battery error. Access authority : 1: Not detect battery error.
Page 17
(c) Logging monitor setting (bit 4) Whether the latest file update time is displayed or not in the file specification field of the logging monitor is set in this setting. 0: Not display the latest file update time. 1: Displays the latest file update time. (3) Response monitoring time setting (switch 3 (lower byte)) This is the setting for timeout time (second) from when a module sends a request to the CPU of the accessed device until the CPU responds to it.
7. External Dimensions (*1) 27.4 90 (3.54) (1.08) Cable diameter 4 + 10 (*2) (Units:mm (in.)) *1: The bending radius near the connectors (reference value: R1) should be four times as long as the cable's outside diameter or more when connecting the twisted pair cable.
8.2 Transport Guidelines Comply with IATA Dangerous Goods Regulations, IMDG code and the local transport regulations when transporting products after unpacking or repacking, while Mitsubishi ships products with packages to comply with the transport regulations. Please consult your carrier for further details.
Page 20
Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi; machine damage or lost profits caused by faults in the Mitsubishi products; damage, secondary damage, accident compensation caused by special factors unpredictable by Mitsubishi;...