HP 9000 rp7440 Quickspecs page 9

QuickSpecs
Configuration
PCI-X 2 port 1000Base T/2 port Ultra320
SCSI
Wide Area Network Interface Cards Wide Area Network Interface Cards Wide Area Network Interface Cards Wide Area Network Interface Cards
2 port Programmable Serial Interface
(PSI) X.25 / Frame Relay / SDLC
Additional Interface Cards Additional Interface Cards Additional Interface Cards Additional Interface Cards
PCI 8 port Terminal Multiplexer
PCI 64 port Terminal Multiplexer
PCI Hyperfabric2 Fiber Adapter
External Server Storage External Server Storage External Server Storage External Server Storage
Connectivity Connectivity Connectivity Connectivity
Integrated Multi-function Integrated Multi-function Integrated Multi-function Integrated Multi-function
Core I/O Core I/O Core I/O Core I/O
AB290A
J3525A
A6748A
A6749A
A6386A
HP has the broadest, most robust server and storage line up in the industry, providing exactly the right fit
for every need. Refer to the Storage Server matrix found in the introductory section of Chapter 4 to see a
matrix that highlights which storage device, server and operating system is interoperable.
The HP 9000 rp7440 Server chassis supports up to two core I/O board sets. Each board set contains
two cards (MP/SCSI and LAN/SCSI), which are installed in different locations. MP/SCSI cards are
installed along the right rear vertical edge of the chassis. The LAN/SCSI cards are installed in the PCI
card bay. The first core I/O board set will support up to two cell boards in the server and all I/O slots.
For support of two hard partitions or for support of the third and fourth integrated disk drive, a second
core I/O board set is required in the host system.
HP 9000 rp7410/rp7420/rx7620 Core I/O cards cannot be carried forward to the HP 9000 rp7440
server.
Both Core I/O board sets are identical. The "primary" and "secondary" Core I/O LAN/SCSI board is
supported by a 530 MB/s link. In addition, in the "primary" core I/O, a SCSI controller from both the
LAN/SCSI board and MP/SCSI board each support a single internal disk drive
Each HP 9000 rp7440 Server core I/O board set provides the following features:
Management Processor: Management Processor: Management Processor: Management Processor: The management processor (MP), located on each MP/SCSI card, is a
dedicated processor that simplifies and extends system management, and also enhances
serviceability. The MP minimizes or eliminates the need for the system administrator to be
physically at the system to perform tasks such as diagnostics, system management, or even hard
resets. The MP in the rp7440 can be configured to failover to a secondary MP (again provided
two core I/O board sets are installed). Here are some of the features enabled by the HP 9000
rp7440 Server management processor:
System management over the Internet or Intranet (telnet or web)
System console redirection
Console mirroring
System configuration for automatic restart
Viewing history log of system events
Viewing history log of console activity
Setting MP inactivity timeout thresholds
Remote system control
Remote power cycle (except for MP housekeeping power)
Viewing system status
DA - 12696 North America — Version 4 — March 3, 2008
11i/Yes 2 LC GigE/2 RJ-
45
11.00 / No RS-530, RS-232,
V.35, RS-449 or
X.21
11.00 / No RS-232
11.00 / No RS-232 or RS-
422
11.00 / No LC Duplex
HP 9000 rp7440 Server HP 9000 rp7440 Server HP 9000 rp7440 Server HP 9000 rp7440 Server
Yes / Yes 15 / 60
Yes / Yes 15 / 30
Yes / No 15 / 120
Yes / No 15 / 960
Yes / Yes 4 / 4
Page 9