Advertisement
Quick Links
INSTALL INSTRUCTIONS S-DMM-XXX-CV-SO
**Does not work on 2008 Police Package Crown Vic with optional CD player**
TOOLS REQUIRED:
HARDWARE:
LINE DRAWING:
• Read all instructions before installing any Havis-Shields Equipment Corp products.
• Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes!
• Use hardware provided with install kit
• For product support: visit the Install Instructions Section of our website at
http://havis.com/Installation/Installation.html, email technicalsupport@havis.com
or call 1-800-524-9900.
1996-2008 CROWN VICTORIA
SWING-OUT DASH MONITOR MOUNT
• Ratchet Wrenches
• Sockets - 7mm, 7/16", 9/16"
• Open End Wrenches - 7/16", 9/16"
• Phillips Screwdriver
• T-20 Torx Driver
• AM/FM (DIN) Removal Tool
QTY:
DESCRIPTION:
1
3/8"-16 x 1 Hex Bolt
2
3/8" Flat Washer
1
3/8" Nylock Nut
4
1/4-20 Hex Flange Serrated Nut
1
3/8" Self Adhesive Loom Clip
1
6" Wire Tie
1
Monitor Adapter Hardware
Always!
PART #:
GSM33028B
GSM31007B
GSM30018B
GSM30023
GSM20032
GSM20034
Varies (monitor specifi c)
This instruction
shows installation of a
Data-911 computer
S-DMM-XXX-CV-SO_INST_3-08a
1
Advertisement
Related Manuals for Havis-Shields 1996-2008 Crown Victoria Swing-Out Dash Monitor Mount S-DMM-XXX-CV-SO
Summary of Contents for Havis-Shields 1996-2008 Crown Victoria Swing-Out Dash Monitor Mount S-DMM-XXX-CV-SO
- Page 1 HARDWARE: QTY: LINE DRAWING: • Read all instructions before installing any Havis-Shields Equipment Corp products. • Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes! • Use hardware provided with install kit • For product support: visit the Install Instructions Section of our website at http://havis.com/Installation/Installation.html, email technicalsupport@havis.com...
- Page 2 Installation: OEM Dash Remove AM/FM Radio, Center Dash Trim, Prior to installation. HVAC Controls. (7mm Socket & DIN Tool) Remove 4 screws at lower end of the upper Remove mounting brackets from new dash dash panel. (7mm socket) monitor mount assembly. Pull out upper dash and tuck #2 bracket Hole in #2 bracket will line up with large behind dash panel.
- Page 3 Attach #2 bracket to dash frame with 3/8” Tighten 3/8 bolt. hex bolt, washers, and nut. (9/16 socket and wrench) Slip #1 bracket over plastic AM/FM radio Reattach center dash trim and run computer support. wires. Run computer wiring through notch (top Attach monitor mount to #1 and #2 brackets passenger side) and place monitor mount into with 1/4”...
- Page 4 Position assembly and tighten bolts. Attach top & bottom dash clamps (#3 bracket) with #8x1” phillips machine screws. Dash mount installed. Check computer Attach computer wiring and monitor adaptor wiring length and fi nd AM/FM wiring. bracket. Note: Some computers require wiring to be Determine desired position of monitor.
- Page 5 Attach monitor bracket to dash mount with Position and wire tire wiring. 1/4” nuts. Wiring complete. Connect AM/FM radio harness and antenna cable. Check radio operation. Snap radio into mount bracket. Dash monitor mount and console installation complete. S-DMM-XXX-CV-SO_INST_3-08a...